Teledex 606-0421-00A - Manual

CONNECTING THE DIAMOND LOBBY

Included with the Diamond Lobby are (one each):

• Base unit

• Coiled handset cord

• User guide

• Handset

• Clear plastic overlay

• Line cord

Contact your supplier or Teledex for information on ordering

custom designed and printed faceplates to enhance the look of your

Teledex Diamond telephone.

1) Located on the left side of the Diamond Lobby is a modular

jack labeled

TO HANDSET.

Insert one end of the coiled handset

cord into this jack. (You should hear the coil cord lick when

properly inserted).

2) Insert the other end of the coiled handset cord into the modular

jack on the handset.

3) Turn the telephone so the back panel is facing you. Insert either

end of the line cord into the jack on the back of the telephone

this jack is labeled

TO TEL.

4) Insert the other end of the line cord into a telephone wall jack.

5) To program the

AUTO DIAL

key(s) see below instructions.

6) Once your telephone is connected, place the paper faceplate over

the keys. The plastic overlay slips into place by hooking the tabs

on the overlay into the recessed slots located on both sides. The

overlay is easiest to insert when; the left or right side tabs are

inserted first, and the middle part of the overlay is slightly bowed

to allow for insertion of the other tabs.

TO PROGRAM THE AUTO DIAL KEY(S)

Remove the plastic overlay and paper faceplate.

The telephone must be connected to a "live" telephone jack. Use the

eraser end of a pencil or pen to depress the dial keys.

1) Lift the handset.

2) Press the

STORE

key and release it.

3) Enter the telephone number including the outside access codes,

by pressing the recessed dial pad numbers, 0-9, as needed.

4) Press the

AUTO DIAL

key located near the bottom of the tele-

phone.

5) Replace the handset (hang up).

NOTE: Depending on your model, there may be one to five AUTO

DIAL keys. Repeat the above process for all available keys.

DATA PORT

The DATA PORT is a modular jack, located on the back of the tele-

phone, labeled

DATA

. You can connect a facsimile or other devices

through the DATA PORT. Insert the modular line cord from your

facsimile, etc., into the jack labeled

DATA

.

HANDSET VOLUME KEY

The handset has three volume levels. When the handset is first lifted,

the handset volume is normal.

To change the HANDSET VOLUME:

Locate the

HANDSET VOLUME

key to the right of the keypad. Press

the key once and the volume level will increase one level (to medium

volume). Press the key once more and the volume level will increase

an additional level (to high volume).

To return the handset volume back to normal, press the handset vol-

ume key again.

RMA PROCEDURES

The following procedure should be followed with all Teledex

telephone products prior to sending the telephone to the factory

for repair.

1) Please perform the tests listed below:

a. Test the telephone on a different telephone jack.

b. Test telephone with a different line cord.

c. Test with a different handset cord (coiled cord).

d. For two line products, please ensure that one of the line

buttons is pressed (if both line buttons are in the UP position,

the telephone will not operate).

2) If the steps listed above do not provide a remedy for the suspect

telephone, please place a tag on the individual telephone

describing the defect. Next, call the Teledex Repair Department

at

1 (800) 875-8539

for an RMA number. You must have an

RMA number to return products to Teledex.

3) Kindly note: An RMA number is unique to each return

shipment. Do not duplicate this number on any future shipments.

SHIPPING INSTRUCTIONS:

Please print the RMA number clearly on the outside of your shipping

carton(s). Please ship to the following address:

Teledex LLC / RMA#___________

6311 San Ignacio Avenue

San Jose, CA 95119

FREIGHT CHARGES:

The Customer is responsible for shipping products for repair to

Teledex. After repair, Teledex will return telephone products to the

Customer freight prepaid in the same manner in which is was sent

(i.e. Freight sent to Teledex UPS Blue, will be returned via 2 day ship-

ping).

**Please note: When telephones are returned for repair due to misuse

(i.e. liquid spills, abuse, or Customer modification - warranty label

broken), the Customer will be charged the standard repair fee, regard-

less of warranty status.

CONVERTING FROM DESK TO WALL MOUNT

The Diamond Lobby telephone can be changed for wall mount

applications. The conversion is easiest when the handset and line

cords are not connected.

1) Located on the front of the telephone above the speaker grill is

the wall/desk mount clip. Remove this clip by firmly pushing

upward (towards the hookswitch).

2) Rotate the clip a half turn (180 degrees) so that the side with the

protruding edge is towards the top. This edge will hold the

handset. (Closest to the hookswitch.)

3) Return the clip to its original location by pushing the clip dow

wards, until it stops (snaps into place).

4) Turn the Diamond Lobby over so that the back side is up, facing

you (A non abrasive surface is suggested to prevent scratching).

5) Locate and remove the mounting bracket, firmly push back and

pull up to remove two of the four retaining tabs.

6) Rotate the mounting bracket a half turn (180 degrees) so that

the mounting eyelet is facing in the same direction as the other

mounting eyelet located on the telephone.

7) Insert the top two retaining tabs of the mounting brackets

into

the mounting bracket slots (located near the middle of the tele-

phone)

. Then firmly push down to insert the retaining tabs on

the opposite side of the mounting bracket.

8) Connect a short modular line cord into the jack on the back of

the phone (labeled

TO TEL

). Route the line cord through the line

cord channel. Connect the other end of line cord to the phone

jack on the wall mounting plate.

9) Turn the telephone over, and slide the Diamond Lobby down

onto the wall plate mounting posts. Both eyelets should line up

with the mounting posts (When properly installed the telephone

will be stable and secure).

DIAMOND LOBBY

GUESTROOM TELEPHONE

USERS GUIDE

Back View — mounting

bracket is shown in the

Desk Mount

Configuration

Removable mounting bracket,

turned 180 degrees (for

Wall

Mount

installation)

Back View — Mounting

bracket shown is in the

Wall Mount

Configuration