Tektronix VX4353 - Manual

Tektronix VX4353

Tektronix VX4353 – Manual, read for free online in PDF format. We hope this helps you resolve any issues you may have. If you have further questions, please contact us through the contact form.

1 Page 1
2 Page 2
3 Page 3
4 Page 4
5 Page 5
6 Page 6
7 Page 7
8 Page 8
9 Page 9
10 Page 10
11 Page 11
12 Page 12
13 Page 13
14 Page 14
15 Page 15
16 Page 16
17 Page 17
18 Page 18
19 Page 19
20 Page 20
21 Page 21
22 Page 22
23 Page 23
24 Page 24
25 Page 25
26 Page 26
27 Page 27
28 Page 28
29 Page 29
30 Page 30
31 Page 31
32 Page 32
33 Page 33
34 Page 34
35 Page 35
36 Page 36
37 Page 37
38 Page 38
39 Page 39
40 Page 40
41 Page 41
42 Page 42
43 Page 43
44 Page 44
45 Page 45
46 Page 46
47 Page 47
48 Page 48
49 Page 49
50 Page 50
51 Page 51
52 Page 52
53 Page 53
54 Page 54
55 Page 55
56 Page 56
57 Page 57
58 Page 58
59 Page 59
60 Page 60
61 Page 61
62 Page 62
Page: / 62

Table of Contents:

  • Page 5 – Contacting Tektronix; To write us
  • Page 7 – EC Declaration of Conformity
  • Page 59 – Conventions Used In This Procedure
  • Page 60 – Equipment Required; Table 1–1: Equipment Required; Connector Wiring; leaving a “pig tail” to connect to the DMM.; Plug this connector into P4 on the VX4353.; Performance Verification Procedure; Verify that all LED’s for CH00 through CH31 are lit.; Verify that all LEDs for Ch00 through CH31 are out.
  • Page 61 – Digital Multi-Meter Connection and Set Up; Set the DMM to the 4 wire Ohms mode, and select autorange.; Testing The Relay Resistance; Verify that the DMM reads less then 300 milliohms.; Remove the connector from P4 and plug connector into P5.; and Ox
  • Page 62 – Testing The Delay Command; and the time for the CH01 LED to light.; b. If working correctly, this time will be approximately 1 second.
Loading the manual

User Manual

VX4353
Relay Switching Module

070-9121-02

This document supports firmware version 1.00

Warning
The servicing instructions are for use by qualified
personnel only. To avoid personal injury, do not
perform any servicing unless you are qualified to
do so. Refer to the Safety Summary prior to
performing service.

"Loading the manual" means you need to wait until the file loads and becomes available for online reading. Some manuals are very large, and the time they take to appear depends on your internet speed.

Summary

Page 5 - Contacting Tektronix; To write us

Contacting Tektronix ProductSupport For application-oriented questions about a Tektronix measure-ment product, call toll free in North America:1-800-TEK-WIDE (1-800-835-9433 ext. 2400)6:00 a.m. – 5:00 p.m. Pacific time Or contact us by e-mail:[email protected] For product support outside of North ...

Page 7 - EC Declaration of Conformity

EC Declaration of Conformity We Tektronix Holland N.V.Marktweg 73A8444 AB HeerenveenThe Netherlands declare under sole responsibility that the VX4353 meets the intent of Directive 89/336/EEC for Electromagnetic Compatibility and LowVoltage Directive 73/23/ECC for Product Safety. Compliance was demon...

Page 59 - Conventions Used In This Procedure

VX4353 Page A – 15 Appendix E Performance Verification Procedure The performance verification procedure verifies that the module is operating within specification. Conventions Used In This Procedure All control of the VX4353 Module will be accomplished through a VXI Slot 0 device.ASCII characters wi...

Other Tektronix Models

All Tektronix Other