Tektronix 73A-270 - Manual

Tektronix 73A-270

Tektronix 73A-270 – Manual, read for free online in PDF format. We hope this helps you resolve any issues you may have. If you have further questions, please contact us through the contact form.

1 Page 1
2 Page 2
3 Page 3
4 Page 4
5 Page 5
6 Page 6
7 Page 7
8 Page 8
9 Page 9
10 Page 10
11 Page 11
12 Page 12
13 Page 13
14 Page 14
15 Page 15
16 Page 16
17 Page 17
18 Page 18
19 Page 19
20 Page 20
21 Page 21
22 Page 22
23 Page 23
24 Page 24
25 Page 25
26 Page 26
27 Page 27
28 Page 28
29 Page 29
30 Page 30
31 Page 31
32 Page 32
33 Page 33
34 Page 34
35 Page 35
36 Page 36
37 Page 37
38 Page 38
39 Page 39
40 Page 40
41 Page 41
42 Page 42
43 Page 43
44 Page 44
45 Page 45
46 Page 46
47 Page 47
48 Page 48
49 Page 49
50 Page 50
51 Page 51
52 Page 52
53 Page 53
54 Page 54
55 Page 55
56 Page 56
57 Page 57
58 Page 58
59 Page 59
60 Page 60
61 Page 61
62 Page 62
63 Page 63
64 Page 64
65 Page 65
66 Page 66
67 Page 67
68 Page 68
69 Page 69
70 Page 70
71 Page 71
72 Page 72
73 Page 73
74 Page 74
75 Page 75
76 Page 76
77 Page 77
78 Page 78
79 Page 79
80 Page 80
81 Page 81
82 Page 82
83 Page 83
84 Page 84
85 Page 85
86 Page 86
87 Page 87
88 Page 88
89 Page 89
90 Page 90
Page: / 90

Table of Contents:

  • Page 3 – WARRANTY
  • Page 5 – EC Declaration of Conformity
  • Page 9 – 3A-270 Arbitrary Pulse/Pattern Generator Module; iii; General Safety Summary; Only qualified personnel should perform service procedures.; Injury Precautions; To prevent product overheating, provide proper ventilation.
  • Page 10 – iv; Safety Terms and Symbols; in injury or loss of life.; Certifications and Compliances; Terms in This Manual
  • Page 65 – Appendix D: Performance Verification; The following skills are required to perform this procedure:; General Information and Conventions; Prerequisites
  • Page 66 – The 73A-270 has been calibrated within the last 12 months; Equipment Required; Table A–1: Required Test Equipment; Item Number and Description
  • Page 67 – Table A–2: Elements of a Minimum 73A-270 –Under-Test System; Table A–3: Test System Configuration; Test Record; Test System Configuration
  • Page 71 – Self Test; 4 V or the internally regulated; Performance Verification Tests; NOTE
  • Page 72 – 00 ns power-on default resolution) active high, for the second List; VXIbus Interface
  • Page 73 – Verify the time base resolution with the following steps:; or; TTL OUT A and B
  • Page 74 – Table A–4: Time Base Resolution Verification; Command to Send; s active high, for a second List entry of 100
  • Page 75 – Table A–5: Pulse Duration Multiplier Verification
  • Page 76 – BPLR OUT A and B
  • Page 77 – Breakpoint Function
  • Page 78 – To verify Ch-A operation with the VXIbus TTL trigger lines, Set the; commands in table A–6 and verifying a 500 kHz pulse-pattern.; VXIbus TTL Trigger Line Verification Ch. A triggered by Ch. B
  • Page 79 – Verify the EXT TRG A input with the following steps:
  • Page 80 – a. Move the oscilloscope CH-2 coaxial cable from TTL OUT A to TTL; Verify a 500 kHz signal and then stop the pulse-patter:; d. Check the remaining TTLTRG1* through TTLTRG7* lines by sending; the commands in table A–7 and verifying the 500 kHz pulse-pattern.; VXIbus TTL Trigger Line Verification Ch. B triggered by Ch. A; TTLTRG Line
  • Page 81 – (Verify that channel B is not putting out any pattern); Verify the EXT TRG B input with the following steps:; by channel A) and then stop the pattern by sending:
  • Page 82 – b. Check that TTL OUT B is held at a TTL high level, which demonstrates; that the pattern stopped at the active high pulse breakpoint.
  • Page 83 – a. Turn the mainframe power off and remove the 73A-270. Change the; (The fourth parameter is numeric one followed by alphabetic O); External Clock and
Loading the manual

User Manual

73A-270
Arbitrary Pulse/Pattern Generator Module

070-9148-03

This document supports firmware version 1.00
and above.

Warning
The servicing instructions are for use by qualified
personnel only. To avoid personal injury, do not
perform any servicing unless you are qualified to
do so. Refer to the Safety Summary prior to
performing service.

"Loading the manual" means you need to wait until the file loads and becomes available for online reading. Some manuals are very large, and the time they take to appear depends on your internet speed.

Summary

Page 3 - WARRANTY

WARRANTY Tektronix warrants that this product will be free from defects in materials and workmanship for a period of three(3) years from the date of shipment. If any such product proves defective during this warranty period, Tektronix,at its option, either will repair the defective product without c...

Page 5 - EC Declaration of Conformity

EC Declaration of Conformity We Tektronix Holland N.V.Marktweg 73A8444 AB HeerenveenThe Netherlands declare under sole responsibility that the 73A-270 meets the intent of Directive 89/336/EEC for Electromagnetic Compatibility.Compliance was demonstrated to the following specifications as listed in t...

Page 9 - 3A-270 Arbitrary Pulse/Pattern Generator Module; iii; General Safety Summary; Only qualified personnel should perform service procedures.; Injury Precautions; To prevent product overheating, provide proper ventilation.

73A-270 Arbitrary Pulse/Pattern Generator Module iii General Safety Summary Review the following safety precautions to avoid injury and prevent damage tothis product or any products connected to it. Only qualified personnel should perform service procedures. While using this product, you may need to...

Other Tektronix Models

All Tektronix Other