Taylor QS22 - Manual

1 Models QS10 & QS22 To the Installer Section 1 To the Installer These machines are designed for indoor useonly. DO NOT install the machine in an area where a water jet could be used to clean or rinse themachine. Failure to follow this instruction may resultin serious electrical shock. Air Clear...

2 Models QS10 & QS22 To the Installer Installation of Cable Kit Kit A.-3 Ft. Restrain Cable (part no. 074948) mustbe installed to limit the movement of the grill. This isnecessary in order to protect the electrical conduitfrom stress. The cable is made of flexible conduit. To install the kit, lo...

3 Models QS10 & QS22 To the Operator Section 2 To the Operator The grill you have purchased has been carefullyengineered and manufactured to providedependable operation. The QS series grills aredesigned to deliver “cook-to-order” menu items. Thetwo-sided cooking method increases speed ofservice ...

4 Models QS10 & QS22 Safety Section 3 Safety We at Taylor Company are deeply concerned aboutthe safety of the operator when he or she comes incontact with the grill and its parts. Taylor has goneto extreme efforts to design and manufacture built-insafety features to protect both you and the serv...

5 Models QS10 & QS22 Operator Parts Identification Section 4 Operator Parts Identification QS10 Figure 2 ITEM DESCRIPTION PART NO. 1 COVER-PULLOUT GREASECAN 072299 2 TRAY A.-GREASE X71906 ITEM DESCRIPTION PART NO. 3 STANDOFF-REAR 079288 4 STANDOFF-FRONT 079289 5 COLLAR-HOLDING 019481

7 Models QS10 & QS22 Operator Parts Identification Accessories Figure 4 ITEM DESCRIPTION PART NO. 1 SHEET-RELEASE QS24 AUTOW/LOOP 072609 2 RETAINER-RELEASE QS 072607 3 CLIP-RELEASE MATERIAL 072673 ITEM DESCRIPTION PART NO. 4 BAR-RELEASE SHEET QS 072608 5 SCRAPER-TEFLON WIPER 075887

8 Models QS10 & QS22 Important: To the Operator Section 5 Important: To the Operator QS10 Figure 5 ITEM DESCRIPTION 1 GAP HANDLE 2 GAP INDICATOR 3 POWER SWITCH 4 TIMER BUTTON - GREEN ITEM DESCRIPTION 5 RAISE BUTTON - RED 6 KEYS 7 INDICATOR LIGHTS 8 LED DISPLAY

11 Models QS10 & QS22 Important: To the Operator Operating Screen and Controls The VERSION SCREEN is viewed when a grill ispowered for normal operation. It indicates theversion of software the microprocessor is using. VER 1.01B Note: If the grill is not equipped with the upper cook surface optio...

12 Models QS10 & QS22 Important: To the Operator For example, item one has been programmed tocook for 135 seconds. The operator wishes to addsalt in the middle of the cook cycle. Timer twoshould then be programmed for 15 seconds. Oncethe cook cycle begins, a tone will sound 15 secondsafter the f...

13 Models QS10 & QS22 Important: To the Operator Maintenance Menu The Maintenance Menu provides five screens toallow managers and service technicians to monitorgrill performance. To enter the Maintenance Menu while any item isdisplayed, press and hold the MENU key forapproximately 5 seconds and ...

16 Models QS10 & QS22 Important: To the Operator Maintenance Menu Flowchart Figure 8

17 Models QS10 & QS22 Operating Procedures Section 6 Operating Procedures The Model QS10 has one 12” (305 mm) lower cooksurface and one 11” (279 mm) upper platen. The Model QS22 has two 12” (305 mm) lower cooksurfaces and two 11” (279 mm) upper platens. The two-sided cooking concept ensures quic...

18 Models QS10 & QS22 Operating Procedures Step 4 Place the release material clips over the releasematerial sheet, pressing them into place over therelease material bar at the top of the platen. Figure 12 Step 5 Check the alignment and tightness of the releasematerial against the upper platen. S...

19 Models QS10 & QS22 Operating Procedures Cooking Procedures Step 1 Make sure that the release material sheets areinstalled. Step 2 Place the power switch(es) in the ON position. Thisilluminates the switch(es). The screen will scrollthrough information messages and then advance tothe first cook...

20 Models QS10 & QS22 Operating Procedures Step 6 While the upper cook surface is in the raisedposition, place the product on the lower cooksurface. Lower the upper cook surface. CAUTION: The grill is hot. To prevent personal injury, always use the handle to lowerthe upper cook surface. Step 7 I...

21 Models QS10 & QS22 Operating Procedures Step 3 Using the rubber wiper squeegee, push the greaseto the rear of the lower surface into the greasetrough. DO NOT use the grill scraper for this step. Step 4 When necessary, use a grill cloth to clean the backsplash shield and the bullnose areas. St...

22 Models QS10 & QS22 Operating Procedures Step 5 Carefully remove the grease tray partition. Take it tothe sink for cleaning. Figure 21 Note: For installation of the grease tray partition, carefully reverse the above steps. Closing Procedures Step 1 Raise the upper cook surface to the raised po...

24 Models QS10 & QS22 Troubleshooting Guide Section 7 Troubleshooting Guide PROBLEM PROBABLE CAUSE REMEDY 1. Grill will not heat. a. Power cord is not connected. a. Check the power connection. b. Circuit breaker is tripped. b. Reset the circuit breaker. c. Power switch is in the OFF position. c....

26 Models QS10 & QS22 Warranty Explanation Section 8 Warranty Explanation Parts Class 103 Parts The warranty for new equipment is one year, with areplacement parts warranty of three months. Class 000 Parts Wear items - no warranty. Class 212 Parts The warranty for new equipment parts is two year...