Page 2 - Complete this page for quick reference when service is required:; Date of Installation:; Information found on the data label:; Voltage; Taylor Company
Complete this page for quick reference when service is required: Taylor Distributor: Address: Phone: Fax: E-mail: Service: Parts: Date of Installation: Information found on the data label: Model Number: Serial Number: Electrical Specs: Voltage Cycle Phase Maximum Fuse Size: A Minimum Wire Ampacity: ...
Page 3 - Table of Contents
Model 8756 Table of Contents Table of Contents Section 1 To the Installer 1 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Installer Safety 1 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Site ...
Page 4 - Table of Contents - Page 2
Table of Contents Model 8756 Table of Contents - Page 2 Closing Procedure 29 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Draining Product From the Freezing Cylinder 30 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Rinsing 30 . ....
Page 5 - To the Installer; Section 1; Installer Safety; NOT; Air Cooled Units
1 Model 8756 To the Installer 131220 Section 1 To the Installer The following information has been included in themanual as safety and regulatory guidelines. Forcomplete installation instructions, please see theInstallation Checklist. Installer Safety In all areas of the world, equipment should be i...
Page 6 - Water Connections; A back flow prevention device is; Electrical Connections; CAUTION: THIS EQUIPMENT MUST BE
2 Model 8756 To the Installer Water Connections (Water Cooled Units Only) An adequate cold water supply must be providedwith a hand shut-off valve. On the underside of thebase pan, two 3/8” I.P.S. (for single-head units) ortwo 1/2” I.P.S. (for double-head units) waterconnections for inlet and outlet...
Page 7 - Beater Rotation; The following procedures must be; Refrigerant
3 Model 8756 To the Installer 131220 S Supply cords used with this unit shall beoil-resistant, sheathed flexible cable notlighter than ordinary polychloroprene or oth-er equivalent synthetic elastomer-sheathedcord (Code designation 60245 IEC 57) in-stalled with the proper cord anchorage torelieve co...
Page 8 - To the Operator; Section 2; Compressor Warranty Disclaimer; only the refrigerant
4 Model 8756 To the Operator 131220 Section 2 To the Operator The unit you have purchased has been carefullyengineered and manufactured to give youdependable operation. This unit, when properlyoperated and cared for, will produce a consistentquality product. Like all mechanical products, it willrequ...
Page 9 - Safety; Section 3; IMPORTANT - Failure to adhere to the; DO NOT
5 Model 8756 Safety 131220 Section 3 Safety We, at Taylor Company, are concerned about thesafety of the operator at all times when they arecoming in contact with the unit and its parts. Taylormakes every effort to design and manufacturebuilt-in safety features to protect both operators andservice te...
Page 11 - Notes
Page 12 - Operator Parts Identification; Section 4
8 Model 8756 Operator Parts Identification Section 4 Operator Parts Identification Figure 1
Page 14 - Beater Door Assembly
10 Model 8756 Operator Parts Identification Beater Door Assembly Figure 2 ITEM DESCRIPTION PART NO. 1 HANDLE A.-DRAW ADJ X55096 1a HANDLE-ADJUSTABLE 028804 1b SCREW-ADJUSTMENT 055092 1c O-RING-1/4 OD X .070W 50 015872 1d NUT-5/16-24 FINISHED HEX 029639-BLK 2 ROD A.-PIVOT-SHORT X22388 3 O-RING-3/8 OD...
Page 15 - Air/Mix Pump Assembly
11 Model 8756 Operator Parts Identification Air/Mix Pump Assembly ITEM DESCRIPTION PART NO. 1 CAP-PUMP 021276-9 2 PIN-RETAINING 021276-8 *3 PUMP A.-SOFT SERVECOMPLETE X22345 3a CYLINDER A.-PUMP 022345-1 3b PIN-RETAINING 021276-8 3c PISTON 021276-2 3d RING-CHECK 2” OD x 1/2 020050 3e O-RING 2-1/8 OD ...
Page 16 - Accessories
12 Model 8756 Operator Parts Identification 140814 Accessories Figure 4 ITEM DESCRIPTION PART NO. 1 BRUSH-MIX PUMP BODY 023316 2 BRUSH-PRESSURE SWITCH 027647 3 BRUSH SET-LVB 050103 4 BRUSH-FEED TUBE 021101 5 BRUSH-DOUBLE ENDED 013072 6 BRUSH-REAR BEARING 013071 ITEM DESCRIPTION PART NO. 7 BRUSH-DRAW...
Page 17 - Important: To the Operator; Section 5
13 Model 8756 Important: To the Operator Section 5 Important: To the Operator Figure 5 ITEM DESCRIPTION 1 POWER SWITCH (TOGGLE) 2 RESET SWITCH 3 MIX REFRIGERATION CONTROL 4 STANDBY KEY 5 WASH KEY ITEM DESCRIPTION 6 AUTO KEY 7 PUMP KEY 8 MIX LOW INDICATOR 9 MIX OUT INDICATOR
Page 18 - Symbol Definitions
14 Model 8756 Important: To the Operator Symbol Definitions To better communicate in the International arena,the words on many of our operator switches andbuttons have symbols to indicate their functions.Your Taylor equipment is designed with theseInternational symbols. = AUTO = ON = OFF = MIX REF =...
Page 19 - Wash; Adjustable Draw Handle; top; always; bottom
15 Model 8756 Important: To the Operator Wash When the WASH key is pressed, the light comes on,indicating beater motor operation. The STANDBY orAUTO modes must be cancelled first to activate theWASH mode. Auto When the AUTO key is pressed, the light comes on,indicating the main refrigeration system ...
Page 20 - Operating Procedures; Section 6; Assembly; MAKE SURE THE POWER SWITCH IS IN; DO NOT lubricate the hex end
16 Model 8756 Operating Procedures Section 6 Operating Procedures The Model 8756 has two freezing cylinders. The sizeof each freezing cylinder is 3.4 quarts (3.2 liters).Mix is stored in the lower front refrigeratedcompartment and is pumped up to the freezingcylinder by an air/mix pump. Duplicate th...
Page 21 - will not
17 Model 8756 Operating Procedures Step 2 Install the drive shaft through the rear shell bearingin the freezing cylinder and engage the hex endfirmly into the gear box coupling. Be sure the driveshaft fits into the drive coupling without binding. Figure 8 Step 3 Check the scraper blades for any nick...
Page 25 - Do not; DO NOT lubricate
21 Model 8756 Operating Procedures Air/Mix Pump Assembly This Model 8756 uses a single-stage pump. Thepurpose of the pump is to transfer specific amountsof air and mix to the freezing cylinder. Step 1 Assemble the piston by sliding the check band andthe o-ring into the grooves on the piston. Do not ...
Page 29 - Sanitizing
25 Model 8756 Operating Procedures Sanitizing Step 1 Prepare a pail of approved 100 PPM sanitizing solu-tion (examples: 2-1/2 gal. [9.5 liters] of Kay-5 R or 2 gal. [7.6 liters] of Stera-Sheen R ). USE WARM WATER AND FOLLOW THE MANUFACTURER'SSPECIFICATIONS. Step 2 Place the pail of sanitizing soluti...
Page 31 - steady
27 Model 8756 Operating Procedures Step 12 When a steady stream of sanitizing solution is flowing from the prime plug hole in the bottom of thefreezer door, press the PUMP key. This willde-activate pump operation. Push down the primeplug and allow the beater to agitate for 5 minutes. Figure 51 Step ...
Page 32 - Priming; fresh
28 Model 8756 Operating Procedures Priming Step 1 Place the mix tank and the cover in the mix cabinet. Step 2 Insert the prongs of the mix probe inside the mixtank. Connect the mix probe in the socketreceptacle. Figure 54 Step 3 Place the free end of the suction line into the mixtank. Figure 55 Step...
Page 33 - Closing Procedure
29 Model 8756 Operating Procedures Step 7 When a steady stream of mix is flowing from theprime plug hole in the bottom of the freezer door,press the PUMP key to stop operation. Figure 58 Step 8 Once the stream of mix stops flowing from the primeplug hole, push down the prime plug. Rinse theprime plu...
Page 34 - Rinsing; cool
30 Model 8756 Operating Procedures Draining Product From theFreezing Cylinder Step 1 Press the AUTO and MIX REF keys to cancelfreezer operation. Step 2 Open the mix cabinet door and remove the mixstorage cover, the mix tank cover, the mix tank, andthe mix probe. Step 3If local health codes permit th...
Page 35 - Cleaning
31 Model 8756 Operating Procedures Step 5 Place an empty pail beneath the door spout. Raisethe prime plug and press the WASH and PUMPkeys. Figure 62 Step 6 When a steady stream of rinse water is flowing fromthe prime plug hole in the bottom of the freezer door,open the draw valve and drain all the r...
Page 36 - Disassembly
32 Model 8756 Operating Procedures Step 6 Place an empty pail beneath the door spout. Raisethe prime plug and press the WASH and PUMPkeys. Figure 66 Step 7 When a steady stream of solution is flowing from theprime plug hole in the bottom of the freezer door,open the draw valve and draw off the remai...
Page 37 - Brush Cleaning
33 Model 8756 Operating Procedures Brush Cleaning Step 1 Prepare a sink with an approved cleaning solution(examples: Kay-5 R or Stera-Sheen R ). USE WARM WATER AND FOLLOW THEMANUFACTURER'S SPECIFICATIONS. If an approved cleaner other than Kay-5 r or Stera r -Sheen is used, dilute it according to the...
Page 38 - Important: Operator Checklist; Section 7; During Cleaning and Sanitizing; CLEANING AND SANITIZING MUST BE; Troubleshooting Bacterial Count
34 Model 8756 Important: Operator Checklist Section 7 Important: Operator Checklist During Cleaning and Sanitizing ALWAYS FOLLOW LOCAL HEALTH CODES. Cleaning and sanitizing schedules are governedby federal, state, or local regulatory agencies,and must be followed accordingly. If the unithas a “Stand...
Page 40 - Troubleshooting Guide; Section 8; PROBLEM
36 Model 8756 Troubleshooting Guide Section 8 Troubleshooting Guide PROBLEM PROBABLE CAUSE REMEDY PAGE REF. 1. No product is being dispensed. a. Low on mix. The MIX OUT light is on. a. Add mix to the mix tank and press the AUTO key. 28 b. The power switch is in the OFF position. b. Place the power s...
Page 45 - Parts Replacement Schedule; Section 9
41 Model 8756 Parts Replacement Schedule Section 9 Parts Replacement Schedule PART DESCRIPTION EVERY 3 MONTHS EVERY 6 MONTHS ANNUALLY Scraper Blades X Drive Shaft Seal X Freezer Door Gasket X Front Bearing X Beater Shoes X Draw Valve O-Rings X Prime Plug O-Rings X Air/Mix Pump O-Rings X Check Rings ...
Page 46 - Section 10 Limited Warranty on Equipment
42 Model 8756 Limited Warranty on Equipment 131220 Section 10 Limited Warranty on Equipment TAYLOR COMPANY LIMITED WARRANTY ON FREEZERS Taylor Company, a division of Carrier Commercial Refrigeration, Inc. (“Taylor”) is pleased to provide this limitedwarranty on new Taylor-branded freezer equipment a...
Page 47 - Limited Warranty on Equipment; LIMITATION OF WARRANTY; must
43 Model 8756 Limited Warranty on Equipment 3. Replacement of wear items designated as Class “000” parts in the Taylor Operator’s Manual. 4. External hoses, electrical power supplies, and machine grounding. 5. Parts not supplied or designated by Taylor, or damages resulting from their use. 6. Return...
Page 48 - Limited Warranty on Parts
44 Model 8756 Limited Warranty on Parts 131220 Section 11 Limited Warranty on Parts TAYLOR COMPANY LIMITED WARRANTY ON TAYLOR GENUINE PARTS Taylor Company, a division of Carrier Commercial Refrigeration, Inc. (“Taylor”) is pleased to provide this limitedwarranty on new Taylor genuine replacement com...
Page 49 - not
45 Model 8756 Limited Warranty on Parts LIMITED WARRANTY EXCEPTIONS This limited warranty does not cover: 1. Labor or other costs incurred for diagnosing, repairing, removing, installing, shipping, servicing or handling ofdefective Parts, replacement Parts, or new Parts. 2. Normal maintenance, clean...
Page 51 - Parts List
Section 12 Parts List 47 Model 8756 Parts List + Available Separately DE S CRI P T IO N P ART NUM BE R QTY . W ARR. CL AS S RE M ARKS ADAPTOR- P UMP- CABI NET 024259 2 103 BEARI N G- REAR SHELL- NI CKEL 031324 2 000 +GUI DE- DRI P SEAL 028992 2 000 +NUT- BRASS BEARI N G 028991 2 000 +W ASHER- BEARI ...
