Page 2 - Complete this page for quick reference when service is required:; Date of Installation:; Information found on the data label:; Voltage
Complete this page for quick reference when service is required: Taylor Distributor: Address: Phone: Fax: E-mail: Service: Parts: Date of Installation: Information found on the data label: Model Number: Serial Number: Electrical Specs: Voltage Cycle Phase Maximum Fuse Size: A Minimum Wire Ampacity: ...
Page 3 - Table of Contents
Table of Contents Model C006 Table of Contents Section 1 Safety 1 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Section 2 To the Installer 3 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Installing th...
Page 4 - Table of Contents - Page 2
Model C006 Table of Contents Table of Contents - Page 2 Dispensing Flavor Shots - Hot Beverages 24 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Dispensing Flavor Shots - Box of Coffee 25 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Dispensing Flavor Shots - Ic...
Page 5 - Section 1; DO NOT; instruction may result in electrocution.
1 Model C006 Safety 120816 Section 1 Safety We at Taylor are concerned about the safety of the operator when he or she comes incontact with the dispenser and its parts. Taylor has gone to extreme efforts to design andmanufacture built-in safety features to protect both you and the service technician...
Page 6 - This unit has many sharp edges that can cause severe injuries.; instruction may result in serious electrical shock.; applicable European Directive.
2 Safety Model C006 DO NOT operate the dispenser unless all service panels and access doors are restrained with screws. Failure to follow this instruction may result in electrocution. Contactyour local authorized Taylor Distributor for service. DO NOT operate the dispenser with larger fuses than spe...
Page 7 - Section 2; Overview
3 Model C006 To the Installer Section 2 To the Installer Overview The flavor shot dispenser Model C006 dispenses nine flavors, combinations of flavors, andliquid sugar products in different volumes. The dispenser is supplied with a cord andgrounding type plug. The dispenser is designed for indoor us...
Page 8 - FOLLOW YOUR LOCAL ELECTRICAL CODES!
4 To the Installer Model C006 Supply cords used with this unit shall be oil-resistant, sheathed flexible cable not lighterthan ordinary polychloroprene or other equivalent synthetic elastomer-sheathed cord(Code designation 60245 IEC 57) installed with the proper cord anchorage to relieveconductors f...
Page 9 - Air Clearance; One year parts and labor, excluding wear items.
5 Model C006 To the Installer Air Clearance Always allow a minimum of 1” (25.4 mm) at the rear and 4” (102 mm) under the unit foradequate air flow. Warranty One year parts and labor, excluding wear items. CAUTION: Warranty is valid only if required service work is provided by an Authorized Taylor Se...
Page 10 - Installing the Flavor Shot Dispenser; Step; Make sure the unit is level.
6 To the Installer Model C006 Installing the Flavor Shot Dispenser Step Action 1 Place the flavor shot dispenser where it will best serveyour operation. 2 Make sure that counters, platforms, and shelves are strongenough to support the weight of the dispenser and fullcontainers of product (109 lbs. [...
Page 11 - Section 3; Exploded View; ITEM
7 Model C006 Operator Parts Identification Section 3 Operator Parts Identification Exploded View ITEM DESCRIPTION PART NO. 1 Switch-Rocker (Power Switch) 048093 2 Tray-Drip 058346 3 Shield A.-Splash X59366 4 Tube A.-Outlet X59334
Page 12 - Inside Cabinet View
8 Operator Parts Identification Model C006 Inside Cabinet View 1 2 3 MAX. FILL LINE LOW LEVEL
Page 13 - Inside Cabinet View Identification; Syrup Tank
9 Model C006 Operator Parts Identification Inside Cabinet View Identification ITEM DESCRIPTION ABBREVIATION PART NO. 1 Syrup Tank 062244- 2 Cover-Tank Mix - - - 059133 3 Decal-Mag-Instruction - - - 059532-TAY IMPORTANT: There are nine individual flavor tanks. The tanks must be placed in theirproper ...
Page 14 - Section 4
10 Important: To the Operator Model C006 Section 4 Important: To the Operator ITEM DESCRIPTION 1 Power Switch 2 Flavor Buttons 3 Product Buttons / Calibration 4 Size Buttons / Calibration 5 Promo Portion Button 6 Box of Coffee Button 7 Sugar Button 8 Indicator Lights (LED) 9 LCD Screen 10 Clean/Cali...
Page 15 - Power Switch; Flavor Shot Buttons
11 Model C006 Important: To the Operator Power Switch When the unit is plugged into a receptacle and the power switch is placed in the ONposition, the power indicator light will illuminate. The power switch is left in the ON positionduring normal operations. Selection Buttons Flavor Shot Buttons The...
Page 16 - Flavor Refill and Level Reset; not; been pressed for 4 seconds, the control is; and; refilled prior to a MIX LOW or MIX OUT condition.
12 Important: To the Operator Model C006 Flavor Refill and Level Reset When a MIX LOW condition is present, the flavor indicator will flash at 1/2 second intervalsand at 1/4 second intervals when a MIX OUT is present. When a MIX OUT condition ispresent, that specific flavor will lock out until it is...
Page 17 - Service Display Menu; = Break In New Product Tube
13 Model C006 Important: To the Operator Service Display Menu The Service Display Menu provides several screens to the operator and technician for set-up, monitoring and evaluation. To enter the Service Display Menu, press the CLEAN/CAL button. The screen will promptthe operator to enter the access ...
Page 18 - Cleaning Flavors and Liquid Sugar; Clean Menu Screen; The Clean Menu screen allows the operator to clean a; maximum of 4 flavors; Upon entry, the screen will read “CLEAN PRESS FLVR”.
14 Important: To the Operator Model C006 Cleaning Flavors and Liquid Sugar Clean Menu Screen The Clean Menu screen allows the operator to clean a maximum of 4 flavors simultaneously, including the sugar. Step Action 1 Press the CLEAN/CAL button. The screen will prompt theoperator to enter the access...
Page 19 - Cleaning All Flavors and Liquid Sugar; Clean All Menu Screen; Remove the flavor tanks from the unit.
15 Model C006 Important: To the Operator Cleaning All Flavors and Liquid Sugar Clean All Menu Screen The Clean All Menu screen allows the operator to clean all the flavors and the liquid sugarsimultaneously. Step Action 1 Remove the flavor tanks from the unit. 2 Clean the inside of the unit with a c...
Page 20 - Prime All Flavors and Liquid Sugar; Prime All Menu Screen; Flavor Refill and Level Reset on page 12.
16 Important: To the Operator Model C006 Prime All Flavors and Liquid Sugar Prime All Menu Screen The Prime All Menu screen allows the operator to prime all of the flavors, including liquidsugar, simultaneously. Be sure that every flavor, including liquid sugar, being primed hasbeen refilled to the ...
Page 21 - Calibrate Flavors and Liquid Sugar; Calibrate Menu Screen
17 Model C006 Important: To the Operator Calibrate Flavors and Liquid Sugar Calibrate Menu Screen The Calibrate Menu screen allows the operator to calibrate and dispense volume for eachflavor and liquid sugar. IMPORTANT: Calibration is by weight, NOT volume. Step Action 1 Place a scale under the dis...
Page 22 - Data Menu; Data Menu Screen; Cleaning Lockout
18 Important: To the Operator Model C006 Data Menu Data Menu Screen The Data Menu screen allows the operator to view the total number of cycles completedsince the last reset for a product flavor combination. Step Action 1 Press the CLEAN/CAL button. The screen will prompt theoperator to enter the ac...
Page 23 - Section 5; Assembly and Start Up; Open the front door to the dispenser.; ALWAYS FOLLOW LOCAL HEALTH CODES!
19 Model C006 Operating Procedures Section 5 Operating Procedures Assembly and Start Up Step Action 1 Plug the machine into an approved receptacle. The powerindicator will illuminate on the front of the dispenser. 2 Open the front door to the dispenser. 3 Remove all tanks and lids. ALWAYS FOLLOW LOC...
Page 24 - Install the sugar feed tube in the liquid sugar container.
20 Operating Procedures Model C006 Cleaning/Sanitizing (Continued) Step Action 10 Press the “1” (X-SM) button to begin cleaning. The threeflavors corresponding to the top row of flavor keys willclean first. Upon completion, the three flavors in the nextrow will clean, followed by the three flavors i...
Page 25 - Product Tube Removal/Installation
21 Model C006 Operating Procedures Product Tube Removal/Installation Step Action 1 Discard any remaining product in the tank. 2 Wash and rinse the tank and the lid. 3 Fill the tank with clean water to the fill line on the tank. 4 Place a cup under the dispensing spout. Note: Refer to the “Clean Flav...
Page 26 - Refer to Cleaning Flavors and Liquid Sugar on page14.
22 Operating Procedures Model C006 Product Tube Removal/Installation (Continued) Step Action 16 Follow the Break In Flavor instructions starting on page 23for the flavor line that was replaced. 17 Refer to Cleaning Flavors and Liquid Sugar on page14. Note: To minimize or eliminate any mistakes when ...
Page 27 - Press the appropriate flavor button.
23 Model C006 Operating Procedures Break In Flavor (Product Tube) Step Action 1 Prepare a cleaning container with an approved 100 PPMcleaning/sanitizing solution (example: Kay-5® or SteraSheen®). USE WARM WATER AND FOLLOW THEMANUFACTURER'S SPECIFICATIONS. 2 Remove all three syrup tanks from the shel...
Page 28 - Dispensing Flavor Shots - Hot Beverages; Select the appropriate cup for the customer's order.
24 Operating Procedures Model C006 Dispensing Flavor Shots - Hot Beverages To dispense flavor shots for hot beverages (Coffee, Hot Chocolate), follow thesesteps: Step Action 1 Select the appropriate cup for the customer's order. 2 Place the cup under the dispensing spout. 3 Press the flavor button. ...
Page 29 - Dispensing Flavor Shots - Box of Coffee; Fill the box of coffee with 108 oz. of coffee.
25 Model C006 Operating Procedures Dispensing Flavor Shots - Box of Coffee To dispense the flavor shots for the box of coffee, follow these steps: Step Action 1 Place a small coffee cup under the dispensing spout andpress the flavor button. 2 Press the Box of Coffee button. This will dispense thepro...
Page 30 - Dispensing Flavor Shots - Iced Coffee; To dispense the flavor shots for Iced Coffee, follow these steps:
26 Operating Procedures Model C006 Dispensing Flavor Shots - Iced Coffee To dispense the flavor shots for Iced Coffee, follow these steps: Step Action 1 Select the appropriate cup for the customer's order. 2 Fill the cup 2/3 full with ice. 3 Place the cup under the dispensing spout. 4 Press the flav...
Page 31 - To dispense the flavor shots for Latté drinks, follow these steps:
27 Model C006 Operating Procedures Dispensing Flavor Shots - Latté (Hot or Iced) To dispense the flavor shots for Latté drinks, follow these steps: Step Action 1 Select the appropriate cup for the customer's order. 2 Fill the cup 2/3 full with ice. Note: Skip this step for hot Latté. 3 Place the cup...
Page 32 - Section 6; Cleaning Procedure; Equipment Cleaning and Maintenance Schedule; Function
28 Cleaning and Maintenance Model C006 101005 Section 6 Cleaning and Maintenance Cleaning Procedure ALWAYS FOLLOW LOCAL HEALTH CODES! To disassemble and clean the unit, the following items will be needed: S Brushes (provided) S Cleaner/Sanitizer (example: Kay-5® or Stera Sheen®) S Single service han...
Page 33 - Section 7; General Troubleshooting; Problem
29 Model C006 Troubleshooting Guide Section 7 Troubleshooting Guide General Troubleshooting Problem Probable Cause Remedy 1. Dispenser will not operate. a. Unit is not plugged in. a. Plug the unit into a receptacle. b. Power switch is in the OFF position. b. Place the power switch in the ON position...
