Page 2 - Complete this page for quick reference when service is required:; Date of Installation:; Information found on the data label:; Voltage
Complete this page for quick reference when service is required: Taylor Distributor: Address: Phone: Service: Parts: Date of Installation: Information found on the data label: Model Number: Serial Number: Electrical Specs: Voltage Cycle Phase Maximum Fuse Size: A Minimum Wire Ampacity: A E May, 2002...
Page 3 - Table of Contents
Model H63 Table of Contents Table of Contents Section 1 To the Installer 1 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Installer Safety 1 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Site P...
Page 5 - Section 1; Installer Safety; Site Preparation
1 Model H63 To the Installer 090130 Section 1 To the Installer The following are general installation instructions. For complete installation details, please see the check out card. Installer Safety In all areas of the world, equipment should be installed in accordance with existing local codes. Ple...
Page 7 - Beater Rotation; Refrigerant
3 Model H63 To the Installer 090130 Beater Rotation Beater rotation must be clockwise as viewed looking into the freezing cylinder. Note: The following procedures must be performed by an authorized Taylor service technician. To correct rotation on a three--phase unit, interchange any two incoming po...
Page 8 - Compressor Warranty Disclaimer
4 Model H63 To the Operator 090130 Section 2 To the Operator The Model H63 shake freezer has been carefully engineered and manufactured to give you dependable operation. This unit, when properly operated and cared for, will produce a consistent, quality product. Like all mechanical products, it will...
Page 11 - Section 4
7 Model H63 Operator Parts Identification 111114 Section 4 Operator Parts Identification H63 ITEM DESCRIPTION PART NO. 1 COVER A.-- HOPPER INS. 053809 2 AGITATOR A. *HT*20 QT X44797 3 PANEL A.-- SIDE LEFT X48285 4 STUD-- NOSE CONE 011390 5 PAN-- DRIP 19-- 1/2 LONG 035034 6 SHIELD-- SPLASH-- WIRE 046...
Page 12 - H63 Door and Beater Assemblies
8 Model H63 Operator Parts Identification H63 Door and Beater Assemblies ITEM DESCRIPTION PART NO. 1 SEAL-- DRIVE SHAFT 032560 2 SHAFT-- BEATER 035527 3 BEATER A.-- 7QT-- 1 PIN X46233 4 BEARING-- FRONT 013116 5 GASKET-- DOOR 5.177ID 016672 6 BEARING-- GUIDE 014496 7 TORQUE A. X17381 8 ARM-- TORQUE 0...
Page 13 - Accessories; L U B E
9 Model H63 Operator Parts Identification Accessories 1 8 4 5 6 7 L U B E R H P 048260 048260 2 3 ITEM DESCRIPTION PART NO. 1 BRUSH-MIX PUMP BODY -3” X 7” WHITE 023316 2 BRUSH-END-DOOR-SPOUT 039719 3 KIT A.-TUNE UP X48404 4 BRUSH-DOUBLE ENDED 013072 ITEM DESCRIPTION PART NO. 5 BRUSH-REAR BRG 1IN.D X...
Page 14 - Section 5; Symbol Definitions
10 Model H63 Important: To the Operator Section 5 Important: To the Operator H63 Item Description 1 Power Switch (Toggle) 2 Liquid Crystal Display 3 LCD Indicator -- MIX LOW (PCB A.--LED) 4 LCD Indicator -- MIX OUT (PCB A.--LED) 5 Consistency Control (Switch--Torque) 6 Light--Indicator--Product Read...
Page 15 - Liquid Crystal Display; Operating Screen Descriptions
11 Model H63 Important: To the Operator Liquid Crystal Display The Liquid Crystal Display (LCD) is located on the front control panel. The LCD is used to show the current mode of operation, and whether or not there is sufficient mix. LED Indicator -- MIX LOW The “MIX LOW” indicator flashes to indica...
Page 18 - Operator Menu
14 Model H63 Important: To the Operator Following are the variable messages which will appear on line 3: 1. POWER SWITCH OFF: Power switch was in the OFF position. 2. MIX OUT PRESENT: There was a mix out condition present. 3. AUTO OR STANDBY OFF: The unit was not in the AUTO or STANDBY mode. 4. NO H...
Page 19 - Clearing Fault Tones
15 Model H63 Important: To the Operator 060807 Clearing Fault Tones To clear the tone for any faults which have been corrected, press the <-- -- arrow key. To see if there is more than one fault, press the MENU/SEL key. When the last fault is displayed, the control will return to the OPERATOR MEN...
Page 22 - Assembly
18 Model H63 Operating Procedures Section 6 Operating Procedures The Model H63 has a one 7 quart (6.6 liter) freezing cylinder. This automatic freezer offers one flavor. We begin our instructions at the point where we enter the store in the morning and find the parts disassembled and laid out to air...
Page 26 - Sanitizing
22 Model H63 Operating Procedures 090130 Sanitizing Step 1 Prepare a pail of an approved 100 PPM sanitizing solu- tion (examples: 2--1/2 gal. [9.5 liters] of Kay--5 R or 2 gal. [7.6 liters] of Stera--Sheen R ). USE WARM WA- TER AND FOLLOW THE MANUFACTURER’S SPECIFICATIONS. Step 2 Pour the sanitizing...
Page 27 - Priming
23 Model H63 Operating Procedures Step 9 Stand the assembled air tubes in the corner of the mix hopper and place the agitator on the agitator housing. Figure 20 Note: If the agitator stops turning during normal operation, remove the agitator from the agitator housing and brush clean these parts with...
Page 28 - Daily Closing Procedures
24 Model H63 Operating Procedures Step 3 Press the AUTO key. When the unit cycles off, the product will be ready to serve. Figure 24 Step 4 Fill the hopper with fresh mix and place the mix hopper cover in position. Note: Use only FRESH mix when priming the freezer. Daily Closing Procedures THIS PROC...
Page 29 - Daily Opening Procedures
25 Model H63 Operating Procedures 090130 Step 5 Install the air tube assembly. Lift and turn the inner air tube of the assembled air tubes so the pin rests on top of the outer air tube. This will close the hole in the assembled air tubes, preventing mix in the hopper from entering the freezing cylin...
Page 30 - Manual Brush Cleaning; Draining Product From The
26 Model H63 Operating Procedures Rinse a single service towel in sanitizing solution and wipe down the freezer door and area around the bottom of the freezer door.Replace the front drip tray and splash shield. MAKE SURE YOUR HANDS ARE SANITIZED BEFORE PERFORMING THIS NEXT STEP!Step 3 Lift hopper co...
Page 31 - Rinsing
27 Model H63 Operating Procedures 090130 Rinsing Step 1 Pour two gallons (7.6 liters) of cool, clean water into the mix hopper. With the brushes provided, scrub the mix hopper, mix level sensing probes, the outside of the agitator housing, and the mix inlet hole. Figure 30 Step 2 With a mix pail ben...
Page 32 - Brush Cleaning
28 Model H63 Operating Procedures Brush Cleaning Step 1 Prepare a sink with an approved cleaning solution (examples: Kay--5 R or Stera--Sheen R ). USE WARM WATER AND FOLLOW THE MANUFACTURER’S SPECIFICATIONS. IMPORTANT: Follow label directions, as too STRONG of a solution can cause parts damage, whil...
Page 33 - Section 7; During Cleaning and Sanitizing; Troubleshooting Bacterial Count
29 Model H63 Important: Operator Checklist 051214 Section 7 Important: Operator Checklist During Cleaning and Sanitizing Cleaning and sanitizing schedules are governed by your State or local regulatory agencies and must be followed accordingly. The following check points should be stressed during th...
Page 34 - Winter Storage
30 Model H63 Important: Operator Checklist 081111 Winter Storage If the place of business is to be closed during the winter months, it is important to protect the freezer by following certain precautions, particularly if the building is subject to freezing conditions. On water cooled freezers, disco...
Page 35 - Section 8
31 Model H63 Troubleshooting Guide Section 8 Troubleshooting Guide PROBLEM PROBABLE CAUSE REMEDY PAGE REF. 1. Soft lock message appears on LCD. a. More than 24 hours since the last heat cycle. a. The freezer must go through a heat cycle every 24 hours. The freezer must now be disassembled and brush ...
Page 40 - Section 9
36 Model H63 Parts Replacement Schedule Section 9 Parts Replacement Schedule PART DESCRIPTION EVERY 3 MONTHS EVERY 6 MONTHS ANNUALLY QTY. Drive Shaft Seal X 1 Scraper Blades X 2 Freezer Door Gasket X 1 Front Bearing X 1 Draw Valve O-Rings X 2 Torque Rotor Guide Bearing X 1 Torque Rotor O-Rings X 2 I...
