Swisher RTB134412V - Manual

Page 2 - . Some states do not; LIMITED WARRANTY; Engine Warranty

2 In the event you have a claim under this warranty, you must return the product to an authorized service dealer. All transportation charges, damage, or loss incurred during transportation of parts submitted for replacement or repair under this warranty shall be borne by the purchaser. Should you ha...

Page 3 - SAFETY PRECAUTIONS; Thank you for choosing Swisher’s 44 ‘’ Trailcutter. Before operating; Never allow children to operate this machine.; Never assume that children will remain where you last saw them.; Always look down and behind before and during backing.

SAFETY PRECAUTIONS This Safety Alert Symbol indicates important messages in this manual. When you see this symbol, carefully read the message that follows and be alert to the possibility of personal injury. Read this manual completely. This machine can amputate hands and feet, and throw objects. Fai...

Page 4 - ASSEMBLY

• Turn off the blades when not cutting. Before leaving the machine, turn off the blades and stop the engine. • Watch for traffic when operating near or crossing roadways. • Do not operate the cutter if it has been dropped or damaged in any manner or if the mower vibrates excessively. Excessive vibra...

Page 5 - OPERATING YOUR TRAILCUTTER; STOPPING THE ENGINE

5 OPERATING YOUR TRAILCUTTER The operation of any mower can produce foreign objects to be thrown into the eyes, resulting in severe eye damage. Always wear certified safety glasses or wide-vision safety goggles over spectacles before staring any cutting machine and while operating such a machine. Th...

Page 6 - Do not attempt to start the unit with the T-handle console in the; ‘’ ENGAGED ’’; BREAKING IN YOUR CUTTER; idle for 5 minutes, breaking in the belt for a longer life.; FRONT TO BACK ADJUSTMENT

6 ENGAGING BLADESNote: Do not attempt to start the unit with the T-handle console in the ‘’ ENGAGED ’’ position. • Engage blades by pulling down the T-handle lever into the horizontal position.• Return lever to the vertical position to disengage blades. See detail on page 14 figure – 8 • The braking...

Page 8 - CUTTER MAINTENANCE

8 GENERAL RECOMMENDATIONS The warranty on this cutter does not cover items that have been subjected to operator abuse or negligence. To receive full value from the warranty, operator must maintain unit as instructed in this manual.Some adjustments will need to be made periodically to maintain your u...

Page 9 - GENERAL TROUBLESHOOTING

The unit is not cutting level. • Level deck. Check air pressure of all tires; make sure they are equal. See tires for maximum inflation. • Without the engine running, make certain blades are installed identically. The engine will not start. • Disengage blades, turn key switch to the “OFF” position, ...

Page 10 - SAFETY AND OPERATIONAL DECALS; OD39-SWISHER FLAG DECAL

SAFETY AND OPERATIONAL DECALS Replace decal immediately if damaged. Order by part number from Swisher Mower and Machine Co. Inc. 1-800-222-8183,8-5 CT M-F OD82-44 RUGGED CUT DECAL OD29-DANGER DECAL OD39-SWISHER FLAG DECAL OD33-5MPH DECAL OD36-Deflector Decal OD55-DANGER DECAL OD45-WARNING DECAL OD10...

Page 11 - HITCH BAR ASSEMBLY; FRONT SKIRT ASSEMBLY

When ordering replacement parts* = USE PAINT CODE: TC=TEX.RED,S=SILVER,TK=TEX.BLACK HITCH BAR ASSEMBLY FIGURE 2 Item # Description Part # 1 5/16-18 X 1 HCC GR5 ZP NB501 2 Metal Strap For Rubber Flap 4853TC 3 Rubber Flapper 10384 4 5/16-18 Nylock Nut NB181 5 Deck Weldment 10357TC FRONT SKIRT ASSEMBLY...

Page 12 - BLADE DRIVER ASSEMBLY

12 FIGURE 4 BLADE DRIVER ASSEMBLY FIGURE 5 Item # Description Part # 1 Stump Jumper Weldment 4859TK 2 3/4 '' Washer ZP NB179 3 Blade 10358 4 3/4''-10 X 2 1/2 ''GR8 Bolt NB611 5 3/4-10 Nyloc Nut NB609 6 1"ID X 2"OD X 14GA Bellville Washer NB738 7 1'' X 1 1/2'' 10GA Washer Hardened PLN NB614HT...

Page 13 - ENGINE PULLEY ASSEMBLY; BELT ENGAGE CONFIGURATION

13 FIGURE 6 ENGINE PULLEY ASSEMBLY NOT ACTUAL ENGINE USED (REF. ONLY) Item # Description Part # 1 1/2''-13 X 2 1/2'' HCC GR5 ZP NB510 2 Idler Arm 6681TK 3 1/2''-13 2-Way Jam Lock Nut NB121 4 1/4''-20 Nylok Nut NB180 5 1/4''-20 X 3/4'' GR5 ZP NB250 6 Clutch Cable Clevis 9023mod 7 Belt Engage Arm 4898...

Page 14 - CONSOLE ASSEMBLY; ENGINE TO BLADE PULLEY

14 FIGURE 9 P/N B527 P/N 4846 P/N BB105 CONSOLE ASSEMBLY FIGURE 8 1 2 3 4 5 6 7 8 13 12 10 11 10 9 14 15 10 16 10 17 WIRING DIAGRAM ( manual start ) FIGURE 10 P/N BA50 ENGINE TO BLADE PULLEY CONFIGURATION 18 Item # Description Part # 1 T Handle for Console 4463TK 2 1/4-20 Nylok Nut NB180 3 5/16-18 N...

Page 16 - TRAILCUTTER

OWNER’S MANUAL 44”ROUGH CUT TRAILCUTTER Each mower has its own model number. Each engine has its own model number. The model number for the mower will be found on the right hand side of the motor mount. The model number for the engine will be found on the top of the blower fan housing.All mower part...

Swisher RTB134412V - Manual

Table of Contents:

Other Manuals for Swisher RTB134412V

Summary

Other Swisher Models