Page 2 - Table of Contents; Features
Table of Contents 1. DVR Features .......................................................................................... 1 2. Overview 2.1 Front Panel .......................................................................................... 1 2.2 Rear Panel ........................................
Page 3 - Programming
6. Recording 6.1 Start Recording .................................................................................. 12 6.2 Stop Recording .................................................................................. 13 6.3 Recording Time on Hard Drive ..............................................
Page 4 - User Manual; Chapter 1: DVR Features
User Manual z 4 Channel BNC Camera Inputs z 1 Channel BNC Video Output z Video Format: NTSC / PAL z Motion Detection with Sensitivity and Area Settings z Time Schedule Recording / Motion Triggered Recording z One ATA-100 (IDE) Hard Disk Interface z USB 2.0 Back up to computer z Remote Control & ...
Page 6 - Installing Hard Drive; hard drive IDE type connection.; Connecting Camera and Monitor; Refer to; Connecting the Power Supply
User Manual 3.1 Installing Hard Drive 1. Unplug the power supply. Never install or uninstall HDD when DVR is on. 2. Pull the HDD tray from the unit using the finger hole. 3. Connect the power cord and data cable to hard disk drive. Make sure the HDD is set to be MASTER according to the hard drive ma...
Page 7 - Chapter 4: Starting the DVR; Detecting Installed Hard Drive; MASTER...
User Manual Chapter 4: Starting the DVR 4.1 Detecting Installed Hard Drive - 4 - 4.2 Recovering Lost Data 4.3 Restore Recording Feature Checking HDD …… MASTER… RECOVER HDD? 04811-101735 (SELECT)YES/(MENU)NO Power Error Detected Restore Hard Disk (Master) OK Restore REC Mode………… OK On the screen it w...
Page 8 - Refer to 6.1 Start Recording; Menu; MAIN
User Manual 4.4 Main Screen When the DVR is turned on the following display will appear with your connected cameras: Upper left: Percentage of hard drive space used Middle: Channel number (CH1 through CH4) Bottom right: Date and Time Bottom left: System/recording status. ( Refer to 6.1 Start Recordi...
Page 9 - Refer to 5.3 Record Select
User Manual PRESS (UP ， DOWN), ENTER (SELECT) PRESS (MENU) TO EXIT MAIN MENU CAMERA SELECT 1 2 3 4 RECORD SELECT 1 2 3 4 RESOLUTION EACH RECORD FRAME 25 RECORD QUALITY HIGH SCHEDULE SET MISCELLANEOUS MENU HARD DISK SET VIDEO MODE PAL MOTION SET FACTORY RESET [ SEL ]: Select/modify settings [ Menu ]:...
Page 10 - EACH Mode
User Manual 5.4 Resolution There are two modes of resolution for video recording: EACH Mode: The DVR compresses and records each video channel separately so you can enlarge a single channel to full screen display and still be recording on all channels. You can also record on specific channels, for e...
Page 11 - SEL; Force Record
User Manual ] 5.6 Record Quality There are three levels of recording quality: High, Normal, and Low. Higher quality records the best images but uses more hard drive space. Record frame rate, record quality and available hard drive space will affect the total recording time of the DVR system. 5.7 Sch...
Page 12 - refer to 5.16 Factory Reset
User Manual 5.8 Miscellaneous Menu-Auto Record When this option is set to “ ON ”, the DVR will automatically continue with the current Record Schedule if no actions occur for 5 minutes. If you choose “ OFF ”, the DVR will not record until you press the [ REC ] button. 5.9 Miscellaneous Menu-Password...
Page 13 - Up
User Manual 5.12 Miscellaneous Menu-Time Set - 10 - 5.13 Hard Disk Set TIME SET ∨ 2008/08/08 20:08:08 PRESS (UP,DOWN), ENTER (SELECT) PRESS (MENU) TO EXIT HARD DISK SET OVERWRITE ENABLED [YES] MASTER HDD SIZ 120042MB MASTER HDD USED 80865MB 77% MASTER HDD FORMAT SLAVE HDD SIZE N/A SLAVE HDD USED N/A...
Page 14 - Record Schedule
User Manual 5.14 Motion Set SENSITIVITY: Use [ Up ] and [ Down ] button to highlight the channel you want to modify and press [ SEL ] to adjust sensitivity of motion detection on each channel. High (1----------9, OFF) Low When “ OFF ”, the channel will not detect motion or trigger motion recording. ...
Page 15 - Press; ] button to reset the DVR to factory defaults. The DVR will; press; If you have forgotten your password and would like to reset, press [; remove the HDD, then reboot the DVR and press [; Pause; Chapter 6: Recording; REC; DVR will display system information on screen.
User Manual 5.15 Video Mode Select NTSC (North America) or PAL (Europe/Australia) video system. 5.16 Factory Reset Press [ SEL ] button to reset the DVR to factory defaults. The DVR will reboot and all custom settings (including password) will be restored to default. Caution: There is no confirmatio...
Page 16 - Stop; Recording Time on Hard Drive
User Manual 1. Hard Drive Usage (Displayed as a percentage) 2. Recording symbol (channel is currently recording) 3. Camera Number 4. Record Mode (QUAD or EACH) 5. Status (REC, Play, FF1, FF2, FF3, REW, PAUSE) 6. HDD Info. ([M] Master Hard disk) 7. Record Schedule: (T) Time or Manual Record (M) Motio...
Page 18 - Chapter 8: USB Programming; to your PC to playback or backup footage.; PC Viewer Program; Insert the CD into your CD-ROM Drive
User Manual Chapter 8: USB Programming Using the provided DVR PC Viewer software, you can connect the DVR Alert to your PC to playback or backup footage. 8.1 PC Viewer Program 1. Insert the CD into your CD-ROM Drive 2. Open CD directory 3. Double click on the “PCViewerInstall.exe” file to install th...
Page 19 - DVR Mode: play video clips saved on DVR’s HDD.; Item Remark
User Manual - 16 - DVR Mode: play video clips saved on DVR’s HDD. PC Mode: play video clips (.mys file) saved on PC 8.3 PC Backup Press button to open the DVR recorded event list and select an event. Press to begin backup. Backup video files can be saved as “.avi” files or “.mys” files. Item Rem...
Page 20 - Chapter 9: Specifications; ITEM
User Manual Chapter 9: Specifications ITEM DESCRIPTION NOTE Video Format NTSC / PAL Operation System None Stand-alone Camera Input Channel 4 channel Composite BNC Video Output Channel 1 channel Composite BNC NTSC 120 frames/second 4×30 frames/second Display Frame Rate PAL 100 frames /second 4×25 fra...
Page 21 - Chapter 10: Appendix
User Manual Chapter 10: Appendix 10.1 System Connection Diagram 10.2 DVR Accessories (included) Power Cord The shape of the plug might be different from different countries or regions. Power Adaptor User’s Manual Software CD Remote Controller USB Cable - 18 -
