Swann SW111-WIP - Manual - manualsarea.com

Page 2 - Contents

- 1 - Contents Introduction ..........................................................................2 Installation ...........................................................................3 Using Ultra View ..................................................................6 To launch the program...

Page 3 - N T R O D U C T I O N; Software User Guide; Ultra View

- 2 - I N T R O D U C T I O N This Software User Guide provides detailed instructions on operating Ultra View , a customized software application with a user-friendly interface allowing you to access and control your camera(s). You can connect up to 16 cameras to monitor different places and record ...

Page 4 - N S TA L L AT I O N; To begin installation:; NOTE; To use Ultra View, you must have Microsoft .NET

I N S TA L L AT I O N Firstly, insert the Installation CD-ROM into your CD drive to initiate the Auto-Run program. The Auto-Run screen provides the following options: z Quick Guide z Advanced Guide z Software Manual z IP Finder z Install Software z Browse z Exit To begin installation: 1. Click Insta...

Page 5 - When the welcome screen appears, click; Click; Browse; to select the destination location to install the; Next; to use the default settings.

2. When the welcome screen appears, click Next . 3. Click Browse to select the destination location to install the software or click Next to use the default settings. - 4 -

Page 6 - again to confirm installation. The setup wizard; Close

4. Click Next again to confirm installation. The setup wizard starts to install the software and the progress bar indicates the installation is proceeding. 5. When installation is complete, click Close . - 5 -

Page 7 - To launch the program; the main screen will appear; Please set the resolution to 1024x768 or above on your

U S I N G U LT R A V I E W To launch the program This section describes the user interface and operating instructions of Ultra View. To launch the program, click Start > Programs > UltraView > UltraView; the main screen will appear as below: NOTE Please set the resolution to 1024x768 or abo...

Page 8 - Item features; CONTROLS Panel

Item features The following describes the function of each item on the main screen: CONTROLS Panel - SETTING: Click to enter the Setting screen of Ultra View. Click again to return to the main screen of Ultra View. - PLAY: Click to play the recorded video file using the media player on the compute...

Page 10 - CAMERA Panel

CAMERA Panel - TRIGGER OUT: Click to turn on the trigger out connector of the camera. This button is available only when the connected camera supports the trigger out connector, which is used to control the external device connected to the camera, such as a light. - SNAPSHOT: Click to capture a st...

Page 12 - Video View Window and Camera List; This window displays the video view

Video View Window and Camera List Video View Window Camera List - Video View Window: This window displays the video view of the selected camera, which can be divided into 4/9/16 windows according to your selection in VIEW SELECTION panel. - Camera List: This list displays the information of the co...

Page 13 - To add a camera; SETTING; in the CONTROLS panel to display the; Add New Camera

To add a camera 1. Click SETTING in the CONTROLS panel to display the Setting screen. 2. Click Add New Camera . - 12 -

Page 15 - OK; . The connected camera will be displayed in the; to return to the Video View Window. The

4. Enter the User name and Password for the camera, and then click OK . The connected camera will be displayed in the Camera List. 5. Click SETTING to return to the Video View Window. The video view of the selected camera will now be displayed. - 14 -

Page 16 - To remove a camera; To link to the Web page of the camera; SETTING > Camera List > Camera Configuration

To remove a camera 1. Click SETTING in the CONTROLS panel to display the Setting screen. 2. Select a camera from the list and click Delete Camera . Select a camera To link to the Web page of the camera Click SETTING > Camera List > Camera Configuration and then Link web page to launch the Web ...

Page 17 - To record video; Schedule Recording Configuration

To record video Ultra View provides three methods to record video clips; one is to click the RECORD/ALL RECORD button to record manually; the second is to record by motion detection; the third is to set the recording schedule in Setting > Recording Configuration > Schedule Recording Configurat...

Page 19 - To configure the recording settings

- Days: First, select the camera from the pull-down list and select Days tab. Then, select the weekday from the day buttons and then set the time period. Click Apply to save the settings. Select a camera To configure the recording settings To configure the recording settings, including the storage f...

Page 20 - Reserved HDD space for each camera:; This option; HDD Free; Click on the camera number

z Reserved HDD space for each camera: This option allows you to set to reserve the storage space on the hard disk drive for the recording of each camera. Before setting the reserve space on the hard disk drive, you can check the available storage space that is displayed in the HDD Free space field. ...

Page 21 - To playback the recorded video; PLAY; button on; Open; to launch the media player to playback.; If your player on the computer doesn’t have the video

To playback the recorded video The recorded video clips are saved ro your computer, and can be played using the media player on the computer, such as Windows Media Player. To start playback, simply click the PLAY button on the CONTROLS panel, and the following dialog screen will appear, allowing you...

Page 22 - To set up motion detection options

To set up motion detection options When the motion detection function of the selected camera is enabled, you can set the Motion Options by selecting Alarm , Recording , Send e-Mail , and Trigger Out under SETTING > Motion Configuration . z Alarm: Select Beep or Music to alert you for the motion d...

Page 24 - Information

Information Click SETTING > About to display the information of the software application. - 23 -