State Water Heaters GS675YRVIT - Manual

7 (a) vent pIpe (B) anode (c) hot water outlet (d) outlet (120 vac) (e) flue Baffle (f) Gas supplY (G) MaIn Manual Gas shut off valve (h) Ground joInt unIon (j) sedIMent trap (drIp leG) (K) outer door (l) unIon (M) Inlet water shut off valve (n) cold water Inlet fIGure 1. replaceMent parts and delIM...

8 tYpIcal InstallatIon fIGure 2. MIXInG valve usaGe This appliance has been design certified as complying with American National Standard for water heaters and is considered suitable for: water (potable) heating and space heating: All models are considered suitable for water (potable) heating and sp...

9 facts to consIder aBout the locatIon Carefully choose an indoor location for the new water heater, because the placement is a very important consideration for the safety of the occupants in the building and for the most economical use of the appliance. this water heater is not for use in manufactu...

10 Minimum clearances between the water heater and combustible construction are 0 inch at the sides and rear, 5.5” (14.0 cm) from the front and 12” (30.5 cm) from the top (standard clearance). If clearances stated on the heater differ from standard clearances, install water heater according to clear...

12 closed water sYsteMs Water supply systems may, because of code requirements or such conditions as high line pressure, among others, have installed devices such as pressure reducing valves, check valves, and back flow preventers. Devices such as these cause the water system to be a closed system. ...

13 Figure 10 shows typical attachment of water piping to water heater. The water heater is equipped with 3/4 inch NPT water connections. note: If using copper tubing, solder tubing to an adapter before attaching the adapter to the water heater connections. do not solder the water lines directly to t...

14 Gas pIpInG Make sure the gas supplied is the same type listed on the model rating plate. The inlet gas pressure must not exceed 14 inch water column (3.5 kPa) for natural and propane gas (L.P.). The minimum inlet gas pressure shown on the rating plate is that which will permit firing at rated inp...

15 sedIMent traps (drIp leGs) A sediment trap (drip leg) should be installed as close to the inlet of the water heater as practical at the time of water heater installation. The sediment trap should be either a tee fitting with a capped nipple in the bottom outlet or other device recognized as an ef...

16 2. A venting system should terminate at least 3 feet above any forced air inlet located within 10 feet. 3. The venting system should terminate at least 4 feet below, 4 feet horizontally from or, 1 foot above any door, window or gravity air inlet into any building. 4. The manufacturer also recomme...

19 cautIon LABEL ALL WIRES PRIOR TO DISCONNECTION WHEN SERVICING CONTROLS. WIRING ERRORS CAN CAUSE IMPROPER AND DANGEROUS OPERATION. VERIFY PROPER OPERATION AFTER SERVICING. fIGure 18. power vent wIrInG scheMatIc.

23 for Your safetY read Before operatInG warnInG: If you do not follow these instructions exactly, a fire or explosion may result causing property damage, personal injury or loss of life. A. This appliance does not have a pilot. It is equipped with an ignition device which automatically lights the b...

24 The water temperature setting was factory set at the lowest temperature; Pressing the “COOLER” button decreases temperature and pressing the “HOTTER” button increases the temperature. Setting the water heater temperature at 120°F (49°C) (Approx. “ ” mark on temperature setting of gas valve) will ...

25 for Your InforMatIon start up condItIons sMoKe/odor It is not uncommon to experience a small amount of smoke and odor during the initial start-up. This is due to burning off of oil from metal parts, and will disappear in a short while. therMal eXpansIon As water is heated, it expands (thermal exp...

26 ventInG sYsteM InspectIon At least once a year a visual inspection should be made of the venting system. You should look for: 1. Obstructions which could cause improper venting. The combustion and ventilation air flow must not be obstructed. 2. Damage or deterioration which could cause improper v...

27 INSTALLED IN SUITABLE AREA: To insure sufficient ventilation and combustion air supply, proper clearances from the water heater must be maintained. See “Locating the New Water Heater” section. Combustible materials such as clothing, cleaning materials, or flammable liquids, etc. must not be place...

28 leaKaGe checKpoInts Never use this water heater unless it is completely filled with water. To prevent damage to the tank, the tank must be filled with water. Water must flow from the hot water faucet before turning “ON” gas to the water heater. A *Condensation may be seen on pipes in humid weathe...

29 Key no. part description 1 pipe nipple 2 stamped steel Burner 2 a cast Iron Burner 3 Burner tube (stamped Burner) 3a Burner tube (cast Iron Burner) 4 Orifice (Stamped Steel Burner) 4A Orifice (Cast Iron Burner) 5 Ignitor/flame sensor (stamped steel Burner) 5a Ignitor/flame sensor (cast Iron Burne...

30 trouBleshootInG GuIdelInes trouBle shootInG Please check guidelines below. For your safety, water heater service should be performed only by a qualified service technician. Read the GENERAL SAFETY INFORMATION section first. INTELLI-VENT TROUBLESHOOTING CHART - USER CONTROL # led status proBleM so...

35 THIS WARRANTY IS APPLICABLE TO THE ORIGINAL OWNER ONLY. If the glass lined tank in this water heater should prove upon examination by the State Water Heaters (warrantor) to have leaked during the warranty period in normal residential use, due to natural corrosion from potable water therein, the w...