StarTech.com usb dual vga cat5 kvm console extender - 650ft/200m - Manual

Instruction Manual 3 Connecting Your KVM Extender Preparing Your Site Before you can install the product, you need to prepare your site. 1. Determine where the local computer will be located and set up the computer. 2. Determine where the console devices (mouse, keyboard, monitor) will be located an...

Instruction Manual 4 Installation Installing the Local Unit 1. Place the Local Unit near the computer. 2. Switch off the computer and disconnect any connected devices. 3. Using the provided StarTech.com integrated KVM cable, connect the end of the cable that has the USB or PS/2 + VGA connectors to t...

Instruction Manual 6 Push-Button Control and LEDs A push-button on the respective top panel of Local Unit and Remote Unit can be used to select the control mode. Push-Button on Remote Unit The button on the top panel of Remote Unit can be used to switch mode between Local and Remote in the sequence ...

Instruction Manual 7 Video Compensation Video Compensation allows the user to adjust the equalization from the Remote Unit console to optimize video performance based on the length of cable being used, as well as other factors that may affect the display, with adjustments available for Equalizer (Sh...

Instruction Manual 8 Hotkey Commands A hotkey command is a short key sequence to select a computer, activate computer scan, and so forth. The KVM Extender interprets keystrokes for hotkeys all the time. And the built-in buzzer generates a high-pitched beep for correct hotkey command; otherwise, one ...

Instruction Manual 10 Hotkey Commands for both Remote Unit and Local Unit Before inserting the hotkey commands, it’s required to launch the leading code ( [Ctrl] + [Ctrl] or [Ctrl] + [Ctrl] + [E] ) depending on Cascade Architecture. Hotkey Commands Function Descriptions Keyboard Push Button [Alt] + ...

Instruction Manual 12 Hotkey Commands for Local Unit Hotkey Commands Function Descriptions Keyboard Push-Button [3] N/A Auto Mode Selection [F3] Latch Time Selection Auto Mode latch time setting: The extender generates 1 to 4 beeps to indicate the duration of latch time: 5, 15, 30, 60 seconds respec...

Instruction Manual 13 Hotkey Commands for Remote Unit The Video Adjustment function is on Remote Unit only. To launch its hotkey command, also start with the specific leading code depending on situation, and then press F11 to enter Video Adjustment Mode. After adjustment, just press Esc to escape fr...

Instruction Manual 14 Hotkey Commands Function Descriptions Keyboard Push-Button [B] (Blue) [G] (Green) [R] (Red) * Choose one color at a time for adjustment Blue/Green/Red Color Adjustment Caps Lock LED Flashing 1. For both 1st and 2nd monitors 1.1 Press or to coarse tune; 8 levels for adjustment 1...

Instruction Manual 15 Specifications Maximum Resolution 1920 x 1200 at maximum UTP cable length Maximum Range 650 feet (200 meters) Network Cabling Type Straight-through Unshielded Twisted Pair (UTP) Cat 5 Connectors Each, Local and Remote Unit 4 x HD-15 female (2 x KVM, 2 x console VGA) 2 x RJ-45 2...

Instruction Manual 16 RJ-45 Connector Pinout Pin Wire Color Pair Function 1 White/ Orange 2 T 2 Orange 2 R 3 White/ Green 3 T 4 Blue 1 R 5 White/ Blue 1 T 6 Green 3 R 7 White/ Brown 4 T 8 Brown 4 R

Instruction Manual 17 Troubleshooting If you encounter problems with the KVM Extender during the installation or operations, please check through this section for a possible solution. If your problem is not listed here and you can not resolve the issue, please contact your local dealer for the faste...

Instruction Manual 19 Technical Support StarTech.com’s lifetime technical support is an integral part of our commitment to provide industry-leading solutions. If you ever need help with your product, visit www.startech.com/support and access our comprehensive selection of online tools, documentation...