Stanton SK ONE - Manual
Stanton SK ONE – Manual, read for free online in PDF format. We hope this helps you resolve any issues you may have. If you have further questions, please contact us through the contact form.
Table of Contents:
- Page 2 – PLEASE READ CAREFULLY BEFORE USE OF THIS PRODUCT; Problem; T RO U B LE S H O O T I N G
- Page 3 – D E S C R I P T I O N O F F U N C TI O N S
- Page 4 – S P E C I A L P R O T E K TI O N
SK ONE
Professional performance mixer
STANTON MAGNETICS, LLC
2821 Evans St. Hollywood, FL 33020
(954) 929-8999 - Fax: (954) 929-0333
[email protected]
OWNER’S M A N U A L
F A D E R C L E A N I N G
The SK ONE faders may need lubrication from time to time. This will extend the
fader life and eliminate any potential damage due to extended heavy usage.
R E P L A C E M E N T P A R T S
To replace the cross or channel faders, follow steps 1 and 2 of the cleaning
instructions. The following replacement parts are available from Stanton or your
local Stanton dealer.
ROTATING AND REPLACING THE INPUT TOGGLE SWITCHES
Cleaning Instr uctions
1
. Remove the 3 fader knobs and 4 screws
located in the corners of the PROTE KT™
(see “
” inside) panel
and take the panel off the mixer.
2
. Remove the fader to be cleaned by
unscrewing the 2 outer screws (removing
the 2 inner screws will detach the fader
from the fader plate) and disconnect the
cable coming from the mixer.
3
. Spray a small amount of cleaner or
lubricant into both ends of the fader and
slide the fader back and forth a few times
to spread the fluid evenly throughout the
fader.
4
. Shake and wipe off excess fluid before
re-assembling the fader.
PL-SK1
Two way input toggle switch
3PL-SK1
Three way input toggle
switch with F LASH™
LF-SK1
Channel input fader
CF-SK1
Crossfader
PP-SK1
PROTEKT™ panel
PS-13US
US Power Supply (110v)
PS-13EU
European Power Supply (220v)
PS-13UK
UK only Power Supply (240v)
ROTATING I N ST RU C TI O NS
1 . Remove the PROTEKT™ panel
2. Remove the 2 outer screws from the tog-
gle switch plate (removing the 2 inner
screws will detach the switch from the
plate)
3. Rotate the plate to the desired position
and tighten the screws back in the top and
bottom holes
R E PLAC I N G I NST RU C TI O NS
1. Remove the PROTEKT™ panel
2. Remove the 2 outer screws from the tog-
gle switch plate (removing the 2 inner
screws will detach the switch from the
plate)
3. Remove the switch assembly and dis-
connect the cable coming from the mixer.
4. Set the replacement switch assembly in
the desired position and place the screws
back in the top and bottom holes.
©
1999
, Stanton Magnetics, LLC
"Loading the manual" means you need to wait until the file loads and becomes available for online reading. Some manuals are very large, and the time they take to appear depends on your internet speed.
Summary
PLEASE READ CAREFULLY BEFORE USE OF THIS PRODUCT FA I LU R E TO FO LLOW T H E I N ST RU C TI O N S P R I N TE D B E LOW M AY VO I D WA R R A N T Y • Follow all security advice printed on your mixer • When removing the unit's AC plug from the power source, grasp and pull the plug, NEVER the cord itse...
1. Gain control: Controls the input sensitivity of each channel. 2. EQ: Individual controls for low and high frequency equalization with (+9/-26 dB) Any changes made to EQ settings will change the overall output level. 3. Pan control: Controls left/right output balance of each channel. 4. Input Fade...
15. Headphone output: Connection for 1/4 inch headphone. Recommended headphone impedance is 32-200 ohms for maximum volume. 16. Master output: TRS balanced (1/4”). 17. Power switch: Selects power "ON" or "OFF". 18. Power supply connector: Input connection for the accompanying power s...
