Stanton SA-12 - Manual
Stanton SA-12 – Manual, read for free online in PDF format. We hope this helps you resolve any issues you may have. If you have further questions, please contact us through the contact form.
Table of Contents:
- Page 2 – P L E A S E R E A D C A R E F U L L Y B E F O R E U S E; T E C H N I C A L S P E C I F I C A T I O N S
- Page 3 – S A - 1 2 F U N C T I O N S & F E A T U R E S; Removable Effects Module; F A D E R C L E A N I N G A N D R E P L A C E M E N T
- Page 5 – TOP PANEL; F O C U S F A D E R V 2
- Page 6 – D E S C R I P T I O N O F F U N C T I O N S
SA-12
D J C R A Z E S I G N A T U R E M I X E R
STANTON MAGNETICS, INC
[email protected] • (954) 689-8833
w w w . s t a n t o n m a g n e t i c s . c o m
OWNER’S M A N U A L
© 2001, Stanton Magnetics, LLC
This unit has been designed and man -
ufactured using quality components.
Therefore, it is warranted to be free
from defects in materials (limited as
specified below), and workmanship for
a period of twelve (12) months from the
original purchase date. During this
period, all service and parts necessary
to repair a defect will be free of charge.
This limited warranty applies to
mechanical parts which are subject to
wear and tear as specified: Faders,
specified durability: 15,000 cycles;
Rotary potentiometers, specified dura -
bility: 10,000 cycles; Switches, speci -
fied durability: 10,000 cycles.
Consequently, the parts listed above
are warranted to be free from defects in
materials and workmanship for a peri -
od of thirty days (30) days from the
original purchase date.
For the warranty to be valid, please
complete the warranty registration card
attached or fill out the online registra -
tion
at www.stantonmagnetics.com
Mail completed warranty cards to:
Stanton Magnetics, Inc,
3000 SW 42st
• Hollywood, FL 33312
W A R R A N T Y
R O T A T I N G A N D R E P L A C I N G T H E O S 2
ROTATING INSTRUCTIONS
1 . Remove the face plate.
2. Remove the 2 outer screws from the
round OS2 plate (removing the 2 inner
screws will detach the fader from the
plate)
3. Rotate the plate to the desired posi -
tion and tighten the screws back into
the top and bottom holes.
REPLACING INSTRUCTIONS
1. Remove the the face plate.
2. Remove the 2 outer screws from the
round plate (removing the 2 inner
screws will detach the fader from the
plate)
3. Remove the OS2 assembly and dis -
connect the cable coming from the
mixer.
4. Set the replacement fader assembly
in the desired position and place the
screws back in the top and bottom
holes.
"Loading the manual" means you need to wait until the file loads and becomes available for online reading. Some manuals are very large, and the time they take to appear depends on your internet speed.
Summary
P L E A S E R E A D C A R E F U L L Y B E F O R E U S E FAILURE TO FOLLOW T H E INSTRUCTIONS PRINTED BELOW MAY VOID WARRANTY • Follow all security advice printed on your mixer • When removing the unit's AC plug from the power source, grasp and pull the plug, NEVER the cord itself! • Avoid placing yo...
S A - 1 2 F U N C T I O N S & F E A T U R E S • Focus Fader V2 Digital Optical Crossfader (Patent Pending) with curve adjustment and reverse switch. • OS2 (Patent Pending) Optical Scratch switches with lock feature • Removable effects module (Patent Pending) . SA-12 includes MOD1: Pitch Shifter,...
1. Mic/Line 3 level control : Controls the output level of the microphone/Line channel. 2. Gain : Controls the gain of each input channel. 3. Mic/ Line 3 EQ : Individual controls for low and high frequency equaliza -tion with (+/-10 dB) 4. EQ : Individual controls for low fre - quency, midrange, and...
