Stanton RM.404 - Manual

RM.404 Top Panel (FUNCTIONS) Section B: Output Controls 3. Master Level: Controls the overall output level of the audio signal sent through the Master connectors (see Output Connections.) 4. Stereo/Mono Switch: Switches the Master output between a stereo or mono signal. Mono mode can be used to acco...

RM.404 Top Panel (FUNCTIONS) Section C: Cue Controls 7. Split Cue: Controls how the CUE will be heard in the headphones. In the "stereo" position, the pre-selected Cue (#29) will be heard as a stereo signal in the head-phones (full stereo audio signal in both ears.) In "split" positi...

RM.404 Top Panel (FUNCTIONS) Section D: Crossfader Controls 12. Fader Start (A): Activates this side (A) of the Crossfader (#13) for use with components with the Fader Start feature. Moving the crossfader awayfrom the left-most position will cause the device (CD / Turntable) to start play-ing. This ...

RM.404 Top Panel (FUNCTIONS) Section E: MP3/Aux In 15. MP3 / Aux. Input: This 1/8" Mini-jack (3.5 mm) input was designed for easy access and connectivity to a variety of portable devices (portable MP3/ mini-disc / CD players / iPods.) Use this input instead of having to re-wirethe back panel of ...

RM.404 Top Panel (FUNCTIONS) Section G: Channel Controls 23. Input selector switch: Selects phono or line input for the corresponding channel. This is a three way switch allowing input from only one device at atime (Phono or either of two Line level inputs (for connections in rear panel ofmixer see ...

RM.404 Rear Panel (FUNCTIONS) Section I: Master Output I. Master Output Connection: These Right & Left XLR connections are used for the Master Output signal. Volume levels for this output are controlled bythe section B front panel controls. NOTE: The TRIM knob sets the maximumvolume allowed for ...

RM.404 Rear Panel (FUNCTIONS) Section L: Channel 4 Inputs L. Channel 4 Input Connections: This group of connections are ALL inputs which are only routed to Channel 4 (select input using section G, (#23) fromtop panel.) Only two lines (L4, L8) and one phono (PH4) OR MIC 3 can beused as inputs here (t...

RM.404 Rear Panel (FUNCTIONS) O. Channel 1 Input Connections: This group of connections are ALL inputs which are only routed to Channel 1 (select input using section G, (#23) fromtop panel). Only one line (L1) and one phono (PH1) can be input here. The“GND” connections are used only for phono inputs...

This is a typical setup you’ll find in many nightclubs: 2 turntables, 2 CD play-ers, plus a microphone for the DJ. Here’s how you would set up your equip-ment with the RM.404: 1. Be sure all equipment is powered “OFF” and all of the RM.404’s Channelfaders and Level knobs are at minimum volume. 2. Co...

Superior Sound Technology The audio quality of the RM.404 is nothing short of revolutionary for DJ mix-ers in its price class. The RM.404 was designed by Stanton’s new productdevelopment team, seasoned audio professionals who have designed worldclass professional recording studio and broadcast mixer...

Technical Specifications Line Inputs.................................................................................7 x 2 (RCA) , -10 dBV / >10 kOhm 1 (1/8” stereo mini-jack), 10 dBV / >10kOhm Phono / CD Inputs...................................2 x 2 (RCA), -46 dBV / -10 dBV / 47 kOhm / >1...

Troubleshooting Problem / Symptom Possible Cause/ Solution No Sound Is the power on? Check the power switch. Makesure the channels are assigned properly to the crossfaders. Make sure INPUT GAIN is turned upand output level control is turned up. Dependingon the input, check the rear panel selectorswi...

Stanton Magnetics, Inc. – Warranty Provision – Returns for Repairs or Replacement WarrantyThrough Stanton’s authorized dealers around the World, Stanton, or one of Stanton’s authorized dis-tributors outside the U.S., will, without charge, repair or replace, at the sole discretion of the entityrespon...