Speed Queen ADG3SRGS113TW01 Installation Manual

Page 3 - WARNING

WARNING WARNING FOR YOUR SAFETY, the information in this manualmust be followed to minimize the risk of fire or ex-plosion or to prevent property damage, personal in-jury or death. W033 WARNING • Do not store or use gasoline or other flammable vapors and liquids in the vicinity of this or anyother a...

Page 4 - Table of Contents; Dimensions

Table of Contents ............................................................................................................... 3 Dimensions ............................................................................................. 5 Installation ...................................................

Page 5 - Electric Dryers

Dimensions Electric Dryers DRY2203N_SVG M L K J I H G F E D C B A A 22.38 in. [569 mm] B 8.0 in. [203 mm] C * 36 in. [914 mm] D * 40.25 in. [1022 mm] E * 43 in. [1092 mm] F 15.4 in. [391 mm] G * 15.44 in. [392 mm] H 26.875 in. [683 mm] I * 4.0 in. [102 mm] J 0.4 in. [11 mm] K * 4.5 in. [114 mm] L 28...

Page 6 - Gas Dryers

Gas Dryers DRY2293N_SVG O N M L K I H G F E D C B A J 1. 3/8 in. N.P.T. Gas Connection A 22.38 in. [569 mm] B 8.0 in. [203 mm] C * 36 in. [914 mm] D * 40.25 in. [1022 mm] E * 43 in. [1092 mm] F 15.4 in. [391 mm] G * 15.44 in. [392 mm] H * 2.8 in. [70 mm] I 2.3 in. [60 mm] J 26.875 in. [683 mm] K * 4...

Page 7 - Before You Start; Supplies; Figure 1; Parts Included; Electric Dryer; Order of Installation Steps; Position and Level the Dryer; Figure 3

Installation Before You Start Supplies For most installations, the basic supplies you will need are: 9/1 6" DRY2023N_SVG 8 7 6 5 3 2 1 4 1. Safety Glasses 2. Power Cord (Electric Models) 3. Wrench 4. Screwdriver 5. Level 6. 5/16 Inch Socket Wrench 7. Duct Tape 8. Teflon Tape (Gas Models) Figure ...

Page 10 - Table 1; Connect Dryer Exhaust System

Area Description Free Standing/Alcove In- stallation Closet Installation A* Dryer sides and rear clearance 0 in. [0 mm] 0 in. [0 mm] B Dryer top clearance 12 in. [305 mm] 12 in. [305 mm] C Dryer front clearance Not Applicable 2 in. [51 mm] D Exhaust duct clearance to com-bustible material 2 in. [51 ...

Page 11 - Figure 4; Exhaust Direction; Table 2

WARNING To reduce the risk of fire, DO NOT use plastic or thinfoil ducting to exhaust the dryer. W354 DRY1915N_SVG 2 1 1. Correct 2. Incorrect Figure 4 • DO NOT use plastic, thin foil or type B ducting. Rigid metal duct is recommended. • Locate dryer so exhaust duct is as short as possible.• Be cert...

Page 13 - Gas Dryers - Connect Gas Supply Pipe; Make certain your dryer is equipped for use with the type of

Gas Dryers - Connect Gas Supply Pipe WARNING To reduce the risk of gas leaks, fire or explosion: • The dryer must be connected to the type of gas as shown on nameplate located in the door re-cess. • Use a new flexible stainless steel connector.• Use pipe joint compound insoluble in L.P. (Lique- fied...

Page 14 - Altitude; Table 4; Connect Electrical Plug (Electric Dryer; Grounding Information

D233I_SVG 2 3 4 1 5 1. New Stainless Steel Flexible Connector – (Use designCSA certified connector) Use only if allowed by local co-des 2. 1/8 in. NPT Pipe Plug 3. Equipment Shut-Off Valve 4. Black Iron Pipe: Shorter than 20 ft. [6.1 m] – Use 3/8 in. [9.5 mm] pipe. Longer than 20 ft. [6.1 m] – Use 1...

Page 15 - Table 5; Table 5; Connecting Power Cord with Three-Wire Plug

WARNING Improper connection of the equipment-groundingconductor can result in a risk of electric shock.Check with a qualified electrician or service person ifyou are in doubt as to whether the dryer is properlygrounded. W038 Do not modify the plug proivded with the cord-kit - if it will notfit the o...

Page 17 - Connecting Power Cord with Four-Wire Plug

3. Use a strain relief and insert end of power cord through power supply hole. D696I_SVG Figure 8 4. Use the three screws from the accessories bag to attach the power cord wires to the terminal block. Refer to Figure 9 . D286I_SVG 3 2 1 1. "L1" Terminal 2. Neutral Terminal 3. "L2" Te...

Page 18 - Reverse Door, if Desired

DRY2468N_SVG 1 1. Ground Screw Figure 12 4. Use a strain relief and insert end of power cord through power supply hole. DRY2469N_SVG Figure 13 5. Attach power cord earth/ground (green) wire to rear bulkhead using earth/ground screw removed in Step 3. DRY2482N_SVG 1 2 3 4 5 6 7 8 1. Neutral Terminal ...

Page 20 - Electric; Connect to 30 Amp circuit.

D620I_SVG Figure 22 9. Reinstall four hinge attaching screws, removed in Step 1. D623I_SVG Figure 23 Wipe Out Inside of Dryer Before using dryer for the first time, use an all-purpose clean-er, or a detergent and water solution, and a damp cloth to re-move shipping dust from inside dryer drum. D618I...

Page 21 - Recheck Steps

is equipped with a cord having an equipment-grounding conduc-tor and a 3 prong grounding plug. The three-prong groundingplug on the power cord should be plugged directly into a polar-ized three-slot effectively grounded receptacle rated 110/120Volts AC (alternating current) 15 Amps. WARNING This dry...

Page 22 - Shut-off Valve Only Applicable on Certain Models

2. Close the loading door and start the dryer in a heat setting (re- fer to the operation instructions). The dryer will start, the ig-niter will glow red and the main burner will ignite. IMPORTANT: If all air is not purged out of gas line,gas igniter may go off before gas is ignited. If thishappens,...

Page 23 - Fast Track for Installing the Dryer

Installer Checklist Fast Track for Installing the Dryer 1 Position and Level theDryer. DRY2634N_SVG 6 Wipe Out Inside ofDryer. D618I_SVG1 CHECK CHECK 2 Connect Dryer ExhaustSystem. DRY1915N_SVG1 7 Plug In the Dryer. Electric D275I_SVG1 Gas D254I_SVG CHECK CHECK 3 GAS ONLY • Connect Gas Sup- ply Pipe...