Sony SNCCX600W - Manual

O v er v iew How to Use This User’s Guide / System Requirements 5 How to Use This User’s Guide This User’s Guide explains how to operate the Network Camera from a computer.The User’s Guide is designed to be read on the computer display. This section gives tips on making the most of the User’s Guide....

O v er v iew Accessing the Camera Using the Web Browser 6 Accessing the Camera Using the Web Browser After the IP address has been assigned to the camera, check that you can actually access the camera using the Web browser installed on your computer. 1 Start the Web browser on the computer and type ...

O v er v iew Accessing the Camera Using the Web Browser 7 Tip The software is optimized for Internet Explorer using medium font. To display the viewer correctly To operate the viewer correctly, set the security level of Internet Explorer to Medium or lower, as follows: 1 Select Tools from the menu b...

Oper at ing t he Camer a Administrator and User 9 Operating the Camera This section explains how to monitor the image from the camera using your Web browser. The functions of the camera should be set by the Administrator. For the setting of the camera, see “Administrating the Camera” on page 19. Adm...

Oper at ing t he Camer a Logging in to System 10 Logging in to System Logging in as a user 1 Start the Web browser on your computer and type the IP address of the camera you want to monitor. The live viewer is displayed. Display sample: Note If the live viewer does not start correctly, the security ...

Oper at ing t he Camer a Configuration of Live Viewer 11 Configuration of Live Viewer This section explains the functions of the parts and controls of the live viewer. For a detailed explanation on each part or control, see the specified pages. Live viewer using ActiveX viewer Main menu Live viewer ...

Oper at ing t he Camer a Configuration of Live Viewer 12 Capture Click to capture a still image shot by the camera and to store it in the computer. Click to open the folder to be saved. Note In the case of Windows VISTA, Windows 7 or Windows 8, if “Enable Protected Mode” is checked in Control Panel-...

Oper at ing t he Camer a Configuration of Live Viewer 13 Monitor image The image shot by the camera is shown here.There are two modes for on-screen pan/tilt/zoom operation using a mouse: Area zoom mode and Vector dragging mode.In the Area zoom mode, clicking will pan or tilt the camera towards the c...

Oper at ing t he Camer a Configuration of Live Viewer 14 Notes • Pan/Tilt limitation The solid PTZ function controls streaming by cropping or reducing a maximum size image.Thus, the more the camera zooms out, the less area to be panned or tilted, and becomes unavailable at the WIDE setting. • Zoom l...

Oper at ing t he Camer a Switching Transmission Mode 15 Panning and tilting by dragging the screen (Vector dragging mode only) When you click on the starting point on the image and drag to the end point, the camera pans/tilts in the direction of the arrow from the starting point to the end point. Th...

Oper at ing t he Camer a Playback viewer 16 Note When connecting via a proxy server, neither Unicast nor Multicast can be selected. Playback viewer You can play, save or delete the movies recorded in the memory card.This function is available only in the following users.• Administrator• When Viewer ...

Oper at ing t he Camer a Playback viewer 17 Search panel Specify the search period. Start Select the start time for searching. End Select the end time for searching. Search Search for recorded movies in the specified period. Search results list Displays the search results from the search panel. You ...

Oper at ing t he Camer a Playback viewer 18 Fast forward Click this button to fast forward the moving being played. Next record Jump to the next movie. Still image capture Save the capture of a recorded movie as a still image file to your computer. Click to open the folder in which the movie is to b...

Adminis tra ting t he Camer a Basic Operations of the Administrator Menu 19 Administrating the Camera This section explains how to set the functions of the camera by the Administrator.For details about monitoring the camera image, see “Operating the Camera” on page 9. This section explains the basic...

Adminis tra ting t he Camer a Configuring the System — System Menu 20 Security Displays the Security menu for setting the login user name and password to specify which computer(s) can connect to the camera. (“Setting the Security — Security Menu” on page 34) PTZ control Displays the PTZ control menu...

Adminis tra ting t he Camer a Configuring the System — System Menu 21 Adjust Select how to set the day and time. Keep current setting: Select if you do not need to set the date and time. Synchronize with PC: Select if you want to synchronize the camera’s date and time with the computer. Manual setti...

Adminis tra ting t he Camer a Configuring the System — System Menu 22 Backup setting data Saves the setting data of the camera in a file.Click Save , and follow the instructions on the Web browser to specify the folder and save the setting data of the camera. The file name preset at the factory is “...

Adminis tra ting t he Camer a Setting the Camera Image and Audio — Video / Audio Menu 23 Setting the Camera Image and Audio — Video / Audio Menu When you click in the Administrator menu, the Video / Audio menu appears.Use this menu to set the functions of the camera.The Video / Audio menu consists o...

Adminis tra ting t he Camer a Setting the Camera Image and Audio — Video / Audio Menu 24 Metal halide lamp: Sets a white balance suitable for photography under a metal halide lamp. White LED: Sets a white balance suitable for photography under the light of white LEDs.When you use the camera's integr...

Adminis tra ting t he Camer a Setting the Camera Image and Audio — Video / Audio Menu 25 Bit rate Set the bit rate of H.264 image transmission for a line, when the CBR function is on. When the bit rate is set to a high level, better image quality can be enjoyed.When you use a Wi-Fi network, we recom...

Adminis tra ting t he Camer a Setting the Camera Image and Audio — Video / Audio Menu 26 Note Permissible logo file specifications;File format: PNG8 with alpha channelImage size: 160 × 120 or smallerWidth (pixels): multiples of 16 When display position number 1, 2 or 3 is selected, the following set...

Adminis tra ting t he Camer a Setting the Camera Image and Audio — Video / Audio Menu 27 Color Specify the color of privacy masks. This setting is common to every privacy mask. Position Select the number corresponding to the display position on the preview screen.After completing the configuration, ...

Adminis tra ting t he Camer a Setting the Camera Image and Audio — Video / Audio Menu 28 Multicast streaming Set whether the camera uses multicast streaming for H.264 video data and audio data or not. It reduces the transmission load on the camera by having a computer of the same segment network rec...

Adminis tra ting t he Camer a Configuring the Network — Network Menu 29 Configuring the Network — Network Menu When you click in the Administrator menu, the Network menu appears.Use this menu to configure the network to connect the camera and the computer.The Network menu consists of the following t...

Adminis tra ting t he Camer a Configuring the Network — Network Menu 30 To obtain the IPv6 address automatically Select Obtain IP address automatically . The IP address, prefix length, default gateway are assigned automatically. Note If you select Obtain IP address automatically , ask the network ad...

Adminis tra ting t he Camer a Configuring the Network — Network Menu 31 Signal Displays the signal strength. If it is lower than 60%, improve the installation environment as follows: 1 Change the installation position of the camera. 2 Adjust the antenna angle of the Wi-Fi router. 3 Change the instal...

Adminis tra ting t he Camer a Configuring the Network — Network Menu 32 3 Click Connect to start the connection by PIN method. It takes up to two minutes to connect to WPS. 4 When the connection is complete, the status will be Connected . The status Connection failure. means the connection was not p...

Adminis tra ting t he Camer a Configuring the Network — Network Menu 33 Secondary DNS server Type the IP address of the secondary DNS server, if necessary. OK/Cancel See “Buttons common to every menu” on page 19. QoS Tab In this tab, you can mark the data traffic packets sent from the device and con...

Adminis tra ting t he Camer a Setting the Security — Security Menu 34 Setting the Security — Security Menu When you click in the Administrator menu, the Security menu appears.The Security menu consists of the User, Access limit, SSL, 802.1X tabs. User Tab Set the user names and passwords of Administ...

Adminis tra ting t he Camer a Setting the Security — Security Menu 35 Note You can access the camera even from a computer having an IP address whose access right is set to Deny , if you enter the user name and password set for the Administrator boxes in the User menu. OK/Cancel See “Buttons common t...

Adminis tra ting t he Camer a Setting the Security — Security Menu 36 For reasons of security, we recommend using this mode only when there is no problem even if perfect security is not saved. Notes • When Use a self-signed certificate (For test use) is selected, the Security Alert dialog appears on...

Adminis tra ting t he Camer a Setting the Security — Security Menu 37 Notes • When using the client authentication, the personal certificate must be successfully installed on the PC to use it. If this preparation cannot be performed, do not configure settings on this tab. Otherwise, you may not be a...

Adminis tra ting t he Camer a Setting the Security — Security Menu 39 4 Select Certificates from the list, then click Add . Certificate Snap-in is displayed. 5 Select Computer account as the certificate administrated in this Snap-in, then click Next . 6 Select Local Computer as the computer administ...

Adminis tra ting t he Camer a Setting the Security — Security Menu 40 TLS: By this method, the supplicant and the server authenticate each other using a certificate. This enables secure port authentication. PEAP: By this method, an EAP password is used for the supplicant authentication and a certifi...

Adminis tra ting t he Camer a Setting the PTZ control — PTZ control Menu / Setting the Camera tampering detection/Motion detection — Action input Menu 41 Setting the PTZ control — PTZ control Menu When you click in the Administrator menu, the PTZ control menu appears.The PTZ control menu consists of...

Adminis tra ting t he Camer a Setting the Camera tampering detection/Motion detection — Action input Menu 42 Motion detection: The alarm is triggered by the motion detection function. VMF: The alarm is triggered by the VMF function. Face detection: The alarm is triggered by the face detection functi...

Adminis tra ting t he Camer a Setting the Camera tampering detection/Motion detection — Action input Menu 43 Passing A passage line is determined, and when a moving object passes the setting line, an alarm sounds. Left object When a moving object has been left in the designated area, an alarm sounds...

Adminis tra ting t he Camer a Setting the Camera tampering detection/Motion detection — Action input Menu 44 After the deletion, the cursor will return to its original form. To exit this operation, click this button again.It is the same function as the button displayed under VMF settings. Add vertex...

Adminis tra ting t he Camer a Setting the Camera tampering detection/Motion detection — Action input Menu 45 Time until left/removed object is detected Enter the time you want to elapse before the alarm is triggered. This setting is available only when the filter type is set to Left object or Remove...

Adminis tra ting t he Camer a Setting the Camera tampering detection/Motion detection — Action input Menu 46 Left object This criterion is for whether a moving object has been left in the trigger area.Similar to an active window, a trigger area can also be moved and vertexes can be moved, added or d...

Adminis tra ting t he Camer a Setting the Camera tampering detection/Motion detection — Action input Menu 47 Trigger speed Specify the minimum and maximum speeds to be detected. • Min. speed and Max. speed can be specified within a scale of 100. • The blue marker for minimum speed cannot be set to t...

Adminis tra ting t he Camer a Setting the Action output — Action output Menu 48 Detection area Specify the effective scope of face detection. You can set the area in the same way as the detection area setting in VMD settings. (page 43)A maximum of ten detection areas can be set. Similar to the detec...

Adminis tra ting t he Camer a Setting the Action output — Action output Menu 49 Authentication Select whether authentication is required when you send an e-mail. None: No authentication is required when an e-mail is sent. SMTP: Select when SMTP authentication is required. POP before SMTP: Select whe...

Adminis tra ting t he Camer a Setting the Action output — Action output Menu 50 None: The name of the sent file will be the image file name. Date & time: The date & time suffix is added to the image file name.The date & time suffix consists of last two-digits of the year (2 digits), mont...

Adminis tra ting t he Camer a Setting the Action output — Action output Menu 51 Overwrite Select On to overwrite the file when there is insufficient memory space.When you select the checkbox, overwrite is enabled. Old records will be overwritten in chronological order. When you deselect the checkbox...

Adminis tra ting t he Camer a Setting the Action output — Action output Menu 52 Voice alert Tab Set the voice alert function, to output audio from the speaker of the camera, when an alarm is triggered by the detection functions. Note Before using the voice alert function, you need to save the audio ...

Adminis tra ting t he Camer a Setting the Schedule — Schedule Menu / Setting the CLOUD service — CLOUD Menu 53 Setting the Schedule — Schedule Menu When you click in the Administrator menu, the Schedule menu appears.The Schedule menu consists of the Schedule tab. Schedule Tab When you click the Sche...

Adminis tra ting t he Camer a Setting the CLOUD service — CLOUD Menu 54 Site code The registered site code appears. Connection status The connection status to the CLOUD service appears. OK/Cancel See “Buttons common to every menu” on page 19.

Others Glossary 55 Others Glossary ActiveX control A component program object that can be used with web pages or other application programs. The technology for creating ActiveX control is part of software developed by Microsoft. Bandwidth control To limit the amount of transmitted data. Bit rate The...

Others Index 57 Index Numerics 802.1X Tab ..................................... 39 A Access limit Tab ............................. 34Access log Tab ............................... 22access rights ..................................... 9Action............................................. 53Action inp...