Page 2 - COPYRIGHT NOTICE
DSR Series COPYRIGHT NOTICE Copyright © by Sony Corporation.All rights reserved. The copyright on all mattersdescribed in this manual belongs to Sony Corporation,and the contents are intended for use by purchasers ofsubject equipment.Fur thermore, Sony Corporation reserves the right torevise this pu...
Page 3 - Table of Contents; Items supported from DSR-DR1000/A disk command
1 DSR series Table of Contents 1. Summary ................................................... 1 2. Interface System Overview ...................... 1 3. Command Block Format (CMD Block) .... 2 3-1. VTP Command .................................................................. 2 3-2. DSR-DR1000/A DIS...
Page 5 - Summary
1 DSR Series START BIT D0 (LSB) D1 D2 D3 D4 D5 D6 D7 (MSB) PARITY STOP BIT (MARK) (SPACE) 1. Summary The DSR series VTR, Remote Control Connector Panel, incorporate with a 9-pin D-Subminiatureconnectors for REMOTE.This connector is utilized for a serial control system. The definition of CONTROLLER a...
Page 6 - Function; VTP Command
2 DSR Series MSD LSD 1 BYTE 1 BYTE 1 BYTE 1 BYTE 1 BYTE CMD-1 CMD-2 DATA-1 CHECKSUM DATA COUNT DATA-n (MAX.15) CMD-1 Function Direction Controller Device 0 SYSTEM CONTROL 1 SYSTEM CONTROL RETURN 2 TRANSPORT CONTROL 4 PRESET & SELECT CONTROL 6 SENSE REQUEST 7 SENSE RETURN 3. Command Block Format ...
Page 7 - into multiple blocks.
3 DSR Series ID CMD1 CMD2 DC CS DATA 1byte 1byte 1byte 1byte 0 to 255byte 1byte 0x31 ^^^^ CMD1 CMD2 0xFF BYTE1 BYTE254 CS DATA BYTE0 ...... 0x30 ^^^^ CMD1 CMD2 0xFF CS DATA BYTE255 3-2. DSR-DR1000/A DISK Command a. ID : Code undefined as CMD1 of Sony VTR 9PIN PROTOCOL.0x30 and 0x31 are designated as...
Page 8 - FUNCTION
4 DSR Series c. CMD1: Specifies the categories of commands. Contents of CMD-1 CMD1 FUNCTION DIRECTION 0x00 VTR SYSTEM CONTROL T → R 0x01 VTR SYSTEM CONTROL RETURN T ← R 0x02 VTR TRANSPORT CONTROL T → R 0x04 VTR PRESET & SELECT CONTROL T → R 0x06 VTR SENSE REQUEST T → R 0x07 VTR SENSE RETURN T ← ...
Page 9 - However, some commands do not fall into these categories.
5 DSR Series [System related commands] 0x00 to 0x07 are the ones that the upper four bits of CMD1 of the Sony VTR 9PIN PROTOCOL isshifted to four bits rightward. The content is the same as that of the Sony VTR 9PIN PROTOCOL.0x10 to 0x12 are in a category related to parameter settings and requests un...
Page 10 - CMD2 code category list
6 DSR Series d. CMD2 : Assigns individual commands according to the following code category list. . CMD2 code category list CMD2 (0x00 to 0xFF) | +----- Operation related codes (0x00 to 0x7F) | | | +-----Basic operation, open operation (0x00 to 0x3F) | | | +-----AUTO/MACRO operation (0x40 to 0x5F) |...
Page 11 - Signal; Connector Pin Assignment; Except for that, it’s become pin assignment of DEVICE.
7 DSR Series External view 1 2 3 4 5 6 7 8 9 T R + _ B A T : Transmit R : Receive A < B “1” (MARK)A > B “0” (SPACE) Signal Controller Device Pin 1 Frame Ground Frame Ground 2 Receive A Transmit A 3 Transmit B Receive B 4 Transmit Common Receive Common 5 Spare Spare 6 Receive Common Transmit Co...
Page 12 - Communication Protocol; In the case that the DEVICE receives the COMMAND required the data
8 DSR Series 5. Communication Protocol 1) All communication between the CONTROLLER and the DEVICE will be under the direct supervi- sion of the CONTROLLER.When the DEVICE receives the COMMAND sent from CONTROLLER, the following COMMANDis returned. . In the case that the DEVICE receives the COMMAND n...
Page 13 - Command; RETURN; Return
9 DSR Series Command 00 . 0C : LOCAL DISABLE 00 . 11 : DEVICE TYPE REQUEST 00 . 1D : LOCAL ENABLE 20 . 00 : STOP 20 . 01 : PLAY 20 . 02 : REC 20 . 04 : STANDBY OFF 20 . 05 : STANDBY ON 20 . 0D : DMC START 20 . 0F : EJECT 20 . 10 : FAST FWD 2X . 11 : JOG FWD 2X . 12 : VAR FWD 2X . 13 : SHUTTLE FWD 20...
Page 25 - Protocol Command; : DEVICE TYPE REQUEST; Model
21 DSR Series BIT-7 BIT-6 BIT-5 BIT-4 BIT-3 BIT-2 BIT-1 BIT-0 FRAMING ERROR OVERRUN ERROR PARITY ERROR TIME OUT CHECKSUM ERROR SOFTWARE OVERRUN UNDEFINED COMMAND 7. Protocol Command 7-1. VTR Command 00 . 0C : LOCAL DISABLE When receiving this command, all functions of the DEVICE will be disabled. 00...
Page 28 - Runs at the set first speed to the point IN.
24 DSR Series 20 ..... 4B : DMC RUN This command is used to let the DEVICE perform a series of operations in the VAR MEMORYmode.1. Cues up the tape to the following point.Point IN _ (set first speed x PREROLL TIME) 2. Runs at the set first speed to the point IN. 3. Stores the speed that is given by ...
Page 29 - For the data format, refer to “24; DF
25 DSR Series 20 . 65 : EDIT ON This command is used to set the DEVICE, which is running at the normal PLAY speed duringthe EDIT PRESET mode, to the EDIT mode.When receiving this command, the DEVICE will start executing after passing the edit delay(three frames) time.For the timing, refer to APPENDI...
Page 31 - This command is used to reset the “DATA No. 8 BIT-6 : LOST LOCK” of the “7X
27 DSR Series BIT-7 BIT-6 BIT-5 BIT-4 BIT-3 BIT-2 BIT-1 BIT-0 VIDEO INSERT ASSEMBLE TIME CODE A2 A1 BIT-7 BIT-6 BIT-5 BIT-4 BIT-3 BIT-2 BIT-1 BIT-0 DA3 DA2 DA1 DA4 1 : EDIT PRESET ON0 : EDIT PRESET OFF DATA-1 DATA-2 DATA-3 DATA-4 0 0 0 5 0 0 0 0 40 . 2D : LOST LOCK RESET This command is used to rese...
Page 32 - : PREREAD MODE SELECT
28 DSR Series 41 . 32 : TAPE/AUTO SELECT The TAPE/EE mode is selected by the value of the DATA-1. [DATA-1] 00 : AUTO01 : TAPEFF : Depends on the DEVICE. 41 . 36 : TIMER MODE SELECT This command is used to select the TIMER system used in the AUTO mode by the value ofDATA-1. This is used for the IN EN...
Page 34 - Input Signal; : EXTENDED DA INPUT SELECT
30 DSR Series BIT-7 BIT-6 BIT-5 BIT-4 BIT-3 BIT-2 BIT-1 BIT-0 DA3 DA2 DA1 DA4 DATA-1 DATA-2 Input Signal BIT-X BIT-X 0 0 DIGITAL AUDIO (AES/EBU) 0 1 ANALOG AUDIO 1 0 NO CHANGE DATA-1 CH-2 CH-1 CH-4 CH-3 DATA-2 MSD LSD MSD LSD 42 . 50 : DA INPUT SELECT This command is used to select the input signal ...
Page 35 - Input video source
31 DSR Series BIT-7 BIT-6 BIT-5 BIT-4 BIT-3 BIT-2 BIT-1 BIT-0 ANALOG SDTI i.LINK INTERNAL SG SDI BIT-7 BIT-6 BIT-5 BIT-4 BIT-3 BIT-2 BIT-1 BIT-0 V/PB/PR G/R/B COMPOSITE S (Y/C) DATA-1 DATA-2 Input video source 01 01 ANALOG COMPOSITE 01 02 ANALOG COMPONENT (Y-R, B) 01 04 G/R/B 01 10 S (Y/C) 02 02 SDI...
Page 36 - AE; : AUDIO MONITOR CHANNEL SELECT
32 DSR Series BIT-7 BIT-6 BIT-5 BIT-4 BIT-3 BIT-2 BIT-1 BIT-0 CH-2 CH-3 CH-4 CH-1 * * * * BIT-7 BIT-6 BIT-5 BIT-4 BIT-3 BIT-2 BIT-1 BIT-0 CH-2 CH-3 CH-4 CH-1 * * * * DATA-1 DF/NDF BIT6 0 NDF 1 DF 41 . 9E : SUPERIMPOSE This command is used to control the SUPERIMPOSE mode of the DEVICE according to th...
Page 38 - CB
34 DSR Series DATA-1 Event No. (Lower byte) Event No. (Upper byte) DATA-2 BIT-7 BIT-6 BIT-5 BIT-4 BIT-3 BIT-2 BIT-1 BIT-0 GEN UB GEN TC 42 . C5 : CLEAR EVENT This command is used to delete the event which is defined by the “4X . C4: DEFINE EVENT” command. [DATA-1, DATA-2] 0000h : Deletes all events....
Page 39 - Response
35 DSR Series Request DATA-1 01 02 03 04 08 10 20 30 11 * * * * * 3 22 * * * * * 3 33 * * * * * 3 Response 74 . 00 : TIMER-1 DATA O 74 . 01 : TIMER-2 DATA O 74 . 04 : LTC TIME DATA O O 78 . 04 : LTC TIME & UB DATA O O 74 . 05 : LTC U-BIT DATA O O 74 . 06 : VITC TIME DATA O * 1 O * 2 78 . 06 : VI...
Page 41 - Request Command
37 DSR Series Request Command Response Command IN DATA SENSE “74 . 10 : IN DATA” OUT DATA SENSE “74 . 11 : OUT DATA” A IN DATA SENSE “74 . 12 : A IN DATA” A OUT DATA SENSE “74 . 13 : A OUT DATA” 78 . 14 : LTC INTERPOLATED TIME & UB DATA The DEVICE is required the LTC TIME DATA and USER’s BIT DAT...
Page 43 - This return command is returned in response to the “60; STATUS DATA
39 DSR Series DATA No. BIT7 BIT6 BIT5 BIT 4 BIT3 BIT2 BIT1 BIT0 0 CASSETTE REF VD HARD LOCAL OUT MISSING ERROR 1 STANDBY TENSION STOP EJECT REW F.FWD REC PLAY ON RELEASE 2 SERVO TSO SHUTTLE JOG VAR REV/FWD STILL CUE UP LOCK MODE COMPLETE 3 AUTO AUDIO OUT AUDIO IN OUT IN MODE 4 SELECT EE FULL EE EDIT...
Page 47 - t READY
43 DSR Series DATA No.8 DATA No.8/BIT-6 : LOST LOCK BIT-6 will be set to “1” when the capstan or drum servo is locked over 10 second, and then theservo is unlocked in the PLAY, REC or EDIT mode.When the DEVICE receives the “40 . 2D : LOST LOCK RESET” command, BIT-6 will be reset. DATA No.8/BIT-4 : E...
Page 49 - This return command is returned in response to the “6X; EDIT PRESET STATUS
45 DSR Series DATA No. BIT7 BIT6 BIT5 BIT4 BIT3 BIT2 BIT1 BIT0 0 INSERT ASSEMBLE VIDEO A3 (TC) A2 (CUE) A1 (CUE) 1 DA4 DA3 DA2 DA1 2 3 4 5 6 7 8 9 A B C D E F 7X . 30 : EDIT PRESET DATA This return command is returned in response to the “6X . 30 : EDIT PRESET SENSE” command from the CONTROLLER. The ...
Page 54 - DEFINE EVENT” command.
50 DSR Series DATA-1 Event No. (Lower byte) Event No. (Upper byte) DATA-2 62 . C4 : EVENT DATA SENSE This command is used to request the contents of the event which is defined by the “4X . C4 : DEFINE EVENT” command. [DATA-1, DATA-2] This specifies the event number which is requested by DATA-1 and D...
Page 56 - This return command is returned in response to the “61
52 DSR Series 7X . C7 : EVENT QUEUE This return command is returned in response to the “61 . C7 : EVENT QUEUE SENSE” com- mand.The events which are waiting for execution are returned in the order of event number.The maximum number of events which can be returned at once is 7 events. When the specifi...
Page 58 - Item
54 DSR Series 7-2. DSR-DR1000/A Disk Command (Ver 1.10 or later) 1. OPEN PLAY & CLOSE (1) OPEN PLAYThe OPEN PLAY command is used in the DSR-DR1000 to cue up to the specified clip, and to play backthe Playlist that is created by the VFL Download or saved by the Clip menu.The DSR-DR1000 identifies...
Page 59 - The statuses at OPEN PLAY in the DSR-DR1000 are shown below.
55 DSR Series DATA No. BIT7 BIT6 BIT5 BIT4 BIT3 BIT2 BIT1 BIT0 1 STANDBY TENSION STOP 0 REW F.FWD REC PLAY ON RELEASE (EJECT) The statuses at OPEN PLAY in the DSR-DR1000 are shown below. FILE OPEN STATUS Value Description FILE OPEN MODE 0x00 OPEN PLAY FILE OPEN STATUS 0x01 NOT OPENED 0x02 IN PROGRES...
Page 60 - and the status data is returned at the timing
56 DSR Series (3) Sequence of OPEN PLAY and CLOSEIn the DSR-DR1000, since the OPEN PLAY command the CLOSE command are required as a pair, theyare described at the same time as follows.Completion of the OPEN PLAY command the CLOSE command can be checked in the DSR-DR1000,by the EJECT bit (bit-4) of t...
Page 62 - VFL Format
58 DSR Series VFL Format [title_field] [CRLF][out_ch] [CRLF][in_point] [SP] [out_point] [SP] [drive_id] [SP] [filename] [SP] [av_select] ( [SP] [OPTION] [SP] [OPTION] ...[OPTION] )[CRLF][in_point] [SP] [out_point] [SP] [drive_id] [SP] [filename] [SP] [av_select] ( [SP] [OPTION] [SP] [OPTION] ...[OPT...
Page 63 - Limitations of VFL NAME; For the files using [; STATUS processing; Command format
59 DSR Series Limitations of VFL NAME In the DSR-DR1000, the VFL NAME that creates problem in the system configuration cannot be used asshown below. . The host system that performs the VFL downloading cannot specify “default.dlt” or “cliplist0.dlt”or“RepeatTmp.dlt” as the VFL NAME. (The filenames fr...
Page 64 - and
60 DSR Series Editor DSR-DR1000 1 Disk : VFL Download Clear 2 VTR : Ack 3 Disk : System Status Sense 4 Disk : System Status 5 Disk : VFL Download Data Set 6 VTR : Ack 7 Disk : VFL Download Data Set 8 VTR : Ack 9 Disk : System Status Sense !/ Disk : System Status !- Disk : VFL Download Data Write != ...
Page 65 - Disk Command Delete
61 DSR Series 3. DELETE (1) DELETEIn the DSR-DR1000, “DELETE” means the DELETE (CLIP/Playlist) processing performed by using theALL DELETE/CLIP DELETE operation commanded by Front Panel (to be abbreviated simply as FPhereafter) and the DELETE (CLIP/Playlist) operation commanded by the Disk command s...
Page 66 - Current Clip
62 DSR Series Editor DSR-DR1000 1 Disk : Delete 2 VTR : Ack 3 Disk : Drive Status Sense 4 Disk : Drive Status (2) DELETE SequenceIn the DSR-DR1000, a series of the commands expected to be issued and executed as described below asthe correct sequence of the DELETE operation. In the DSR-DR1000, the co...
Page 70 - and by the triangle marks(; ITEM
66 DSR Series The items that are supported as the File Entry in the DSR-DR1000 are identified by the round marks ( O ) and by the triangle marks( T ) in the following table. At the same time, the items that are shown with the crossing mark ( X ) are filled with 0x00 to create the FILE SYSTEM DATA. I...
Page 73 - REQUEST TIME BIT MAP
69 DSR Series (9) CURRENT TIME SENSEIn the DSR-DR1000, the CURRENT TIME SENSE is the command that aims at inquiry of the CurrentTime of the present status (when recording/playback is in progress). Command format Item Size Value Description DC 1 0x02 Data Count CMD1 1 0x1A Command1 CMD2 1 0xC0 Comman...
Page 74 - READ STATUS BIT MAP
70 DSR Series (10) CURRENT TIMEIn the DSR-DR1000, the CURRENT TIME is the status that aims at returning the Current Time of thepresent status (while recording/playback is in progress). Command format Item Size Value Description DC 1 0xXX Data Count CMD1 1 0x1B Command1 CMD2 1 0xC0 Command2 DATA1 1 0...
Page 76 - Open Play Command supporting ENDLESS MODE
72 DSR Series 7-3. Items supported from DSR-DR1000/A disk command V2.00 1. Open Play Command supporting ENDLESS MODE In V2.00 or later, by setting ENDLESS MODE that exists in the Option of the Open Play Command, anopened file can be played back repeatedly.Description of Open Play Commands is as foll...
Page 77 - : Select whether or not to specify the START position.; Status
73 DSR Series * 1: Select whether or not to specify CHANNEL. (Ignore Bit even when it is 1. However match Data’s offset.)0 : Do not specify CHANNEL.1 : Specify CHANNEL. * 2: Select whether or not to specify the START position. 0 : Do not specify the START position.1 : Specify the START position. * 3...
Page 78 - Correction of the CLOSE Command; Current Time; VFL Download for the CLIP being recorded
74 DSR Series 2. Correction of the CLOSE Command In V2.00 or later, VFL can be downloaded during the CLOSE state. In V1.10 or later, at CLOSE after opening the VFL, aVFL that has the same name with the VFL that had been open could not be created. 3. “CR” and “LF” in the VFL DOWNLOAD SET Command In V...
Page 79 - COMMAND; E5 : EXTEND VIDEO INPUT SELECT; MODE; The DATA-4 setting is valid in the following cases.
75 DSR Series 7-4. Special Commands for HVR Series In the HVR series, the extension commands are located in the DEVICE DEPENDENT area of the 9-pincommand table.These commands interpret DATA-1 as CMD-3. 7-4-1. Command Table COMMAND RETURN HVR-1500 HVR-1500A 0X . FA . E5 : EXTEND VIDEO INPUT SELECT 10...
Page 80 - FB; FB; FB
76 DSR Series 01 . FB . E5 : EXTEND VIDEO INPUT SENSE This command is used to inquire video input selection status.Send back the “14 . FB . E5 : EXTEND VIDEO INPUT STATUS” command to see the setting in DATA-2 to DATA-4. 14 . FB . E5 : EXTEND VIDEO INPUT STATUS This command is used to send video inpu...
Page 81 - Time Data Format; C : CURRENT TIME SENSE”. Flags conforming to the TIME CODE FORMAT
77 DSR Series DATA-1 DATA-2 DATA-3 DATA-4 BIT7 BIT0 DF 10F 1F 1S 10S 1M 10M 1H 10H Frame No. Field No. F1 F2 F1 F2 F1 F2 F1 F2 F1 F2 F1 F2 N-3 N-2 N-1 N N+1 N+2 EDIT ON/FULL EE ON/SELECT EE ON 6 ms EDIT OFF/FULL EE OFF 6 ms command execution period 8. Time Data Format The following shows the time da...
Page 86 - Printed in Japan; Sony Corporation
Printed in Japan Sony Corporation 2008. 6 16 ©1997 D S R - 6 0 D S R - 6 0 P D S R - 7 0 D S R - 7 0 P D S R - 7 0 A D S R - 7 0 A P D S R - 8 0 D S R - 8 0 P D S R - 8 5 D S R - 8 5 P D S R - 1 5 0 0 D S R - 1 5 0 0 A D S R - 1 5 0 0 P D S R - 1 5 0 0 A P D S R - 1 6 0 0 D S R - 1 6 0 0 A D S R - 1...
