Snapper Simplicity RZT Riding Mowers - Manual
Snapper Simplicity RZT Riding Mowers – Manual, read for free online in PDF format. We hope this helps you resolve any issues you may have. If you have further questions, please contact us through the contact form.
Table of Contents:
- Page 3 – FIGURE 9
- Page 4 – ATTACH TO ALL
- Page 5 – WARNING
- Page 6 – SHEET 1
- Page 10 – NOTES
1
#7600029 TRIPLE BAG CATCHER KIT FOR
44 & 50” SNAPPER / SIMPLICITY RZT RIDING MOWERS
WARNING
DO NOT attempt any adjustments, maintenance, repairs, or service with engine running. Stop engine. Engage
parking brake. Remove key. Remove spark plug wire and secure wire away from spark plug. Engine, muffler and
surrounding areas are extremely hot. Avoid serious burns; allow components to cool down before installing kit.
Replace worn or damaged parts prior to operating. Use approved fuel container. DO NOT smoke near open fuel
container. DO NOT fill fuel tank indoors or when engine is running. Allow engine to cool for at least ten minutes
before refilling. Make sure that fuel cap is tightened securely. Wipe off any spilled fuel before starting engine.
!
STEP 1:
Remove the two innermost front carriage bolts
securing the unit footrest to the frame. Install the seven
ballasts against the front of the machine, securing with the
supplied 5/16 x 2-1/2” carriage bolts and lock nuts in place
of those removed. Tighten hardware securely. See Figure 1.
STEP 2:
Install the baffles to the inside front of the mower
deck:
NOTE:
Prior to installation, remove any existing baffle(s)
that may be installed to the inside front of the deck.
a.
Measure the baffles to determine which are needed. See
Figure 2.
b.
Secure the left baffle to the inside front of the deck with
four 5/16 x 5/8” carriage bolts and flange nuts. See Figure 3.
c.
Secure the right baffle to the inside front and bottom of the
deck with three 5/16 x 5/8” carriage bolts and flange nuts.
See Figure 3. Be sure to tighten all hardware securely.
STEP 3:
Raise the discharge deflector. See Figure 4.
FIGURE 2
INSTRUCTION No. 7101095 (I.R. 9/19/2006)
TP 200-5231-IR-AT-SN
FIGURE 3
!
RIGHT BAFFLE
(Components removed for clarity)
FIGURE 4
FIGURE 1
REMOVE EXISTING HARDWARE
CARRIAGE BOLTS
BALLASTS (7)
LOCK
NUT (2)
LEFT BAFFLE
RAISE
DEFLECTOR
"Loading the manual" means you need to wait until the file loads and becomes available for online reading. Some manuals are very large, and the time they take to appear depends on your internet speed.
Summary
b. Install the catcher support onto the unit, securing with the hardware noted in Figure 9. Tighten all hardware securely. NOTE: Be sure to reinstall any components that may have been removed when removing the hardware in Step 7a. STEP 8: Insert the bagger channel into the grass catcher support, and...
STEP 12: Assemble the discharge tubes: a. Install one strap assembly to each of the locations marked ‘A’ in Figure 16. Insert one #10-24 x 5/8” pan headscrew, fitted with one #10 x 1/2” OD flat washer, out throughthe hole in the tube or adapter. Secure with one #10 x 3/4”OD flat washer, strap, and #...
STEP 13: Assemble the grass containers: a. Match each container section with its corresponding sections (see Figure 18):Container 1 A1, A2, A3 Container 2 B1, B2, B3 Container 3 A1, A2, A3 (or B1, B2, B3). b. With the matched numbers aligned, insert the bottom section (A3, B3) of each container thro...
