Page 2 - This page intentionally blank
Page 3 - preliminaries; Mower Unit
GVTP SM32-R0303.1 1 preliminaries Congratulations! You have just purchased one of the finest pieces of outdoor power equipment on the market today. If properly cared for, your new mower will provide years of dependable service. Please read and follow this instruction manual carefully in order to get...
Page 4 - safety rules regarding outdoor power equipment; PLEASE READ THE FOLLOWING BEFORE ASSEMBLING OR OPERATING UNIT; TRAINING
GVTP SM32-R0303.1 2 safety rules regarding outdoor power equipment PLEASE READ THE FOLLOWING BEFORE ASSEMBLING OR OPERATING UNIT TRAINING • Read, understand, and follow all instructions in the manual and on the unit before starting. If the operator(s) or mechanic(s) can not read English it is the ow...
Page 5 - SLOPE OPERATION; Do; CHILDREN
GVTP SM32-R0303.1 2 safety rules regarding outdoor power equipment (cont.) SLOPE OPERATION Slopes are a major factor related to loss-of-control and tip-over accidents, which can result in severe injury or death. All slopes require extra caution. If you cannot back up the slope, or if you feel uneasy...
Page 6 - unit assembly; CASTER ASSEMBLY
GVTP SM32-R0303.1 2 safety rules regarding outdoor power equipment (cont.) • Grass catcher components are subject to wear, damage, and deterioration, which could expose moving parts or allow objects to be thrown. Frequently check components and replace with manufacturer’s recommended parts, when nec...
Page 7 - DISCHARGE DEFLECTOR ASSEMBLY; TRANSMISSION SHIFT LEVER ASSEMBLY
GVTP SM32-R0303.1 3 unit assembly (cont.) DISCHARGE DEFLECTOR ASSEMBLY • Attach discharge deflector (1:5) using two 5/16" x ¾ " bolts and lock nuts (1:6-7). CAUTION: Do not over tighten lock nuts. TRANSMISSION SHIFT LEVER ASSEMBLY • Install Shift indicator panel (2:45) onto rear of engine de...
Page 8 - FUEL TANK ASSEMBLY
GVTP SM32-R0303.1 3 unit assembly (cont.) TRANSMISSION SHIFT LEVER ASSEMBLY (cont.) • Position ‘double-D’ hole in bottom leg of shift lever onto transmission stud, then slowly move handle of shifter back and forth until hole drops onto matching base of stud. • Replace washer and nut onto transmissio...
Page 9 - HANDLE ASSEMBLY INSTALLATION
GVTP SM32-R0303.1 3 unit assembly (cont.) HANDLE ASSEMBLY INSTALLATION • Install handle assembly (4:1) to upper portion of engine deck using four 1/2" x 1-1/4" hex bolts and serrated flange nuts (4:3-4). Adjust for comfortable operation, then tighten securely. • Locate wiring harness and rou...
Page 10 - unit operation; STARTING THE ENGINE; BEFORE STARTING ENGINE:; oil; CLOSED
GVTP SM32-R0303.1 4 unit operation STARTING THE ENGINE IMPORTANT NOTE: The procedures outlined within this section are general guidelines, and are in no way meant to replace or supercede engine manufacturer’s operating instructions. In order to obtain optimum performance from your engine, refer to y...
Page 11 - MOWER OPERATION; DO NOT OPERATE A DEFECTIVE UNIT –
GVTP SM32-R0303.1 4 unit operation (cont.) STARTING THE ENGINE (cont.) • Grasp recoil handle and pull briskly. You may have to pull several times before engine starts. (If engine fails to start within a reasonable amount of time, discontinue and check engine manual for further instructions.) Note: D...
Page 12 - ENGAGING THE CUTTING BLADES:; ENGAGING THE TRANSMISSION:; LOCKING BRAKES
GVTP SM32-R0303.1 4 unit operation (cont.) • Learn to listen to your machine – being aware of what a well-running unit sounds like can alert you to a potential problem. A straining engine or clanging blades or a slapping belt mean that trouble is almost sure to follow. ENGAGING THE CUTTING BLADES: N...
Page 13 - ADJUSTING CUTTING HEIGHT:
GVTP SM32-R0303.1 4 unit operation (cont.) • Move the shift lever to first gear (‘1’), unlock brakes, and slowly release the brake handles. • Your mower has five forward speeds (‘1’ – ‘5’); simply slide the shifter lever to the appropriate indicator position to select that gear. The machine can be s...
Page 14 - maintenance
GVTP SM32-R0303.1 5 maintenance GENERAL: • Follow implicitly the engine manufacturer’s recommendations for maintenance. • Always keep your machine clean - especially the engine deck. Check all adjustments periodically. Also, periodically check that all fasteners are secure. Remember, sharp blades cu...
Page 16 - SCREW
GVTP SM32-R0303.1 5 maintenance (cont.) • THROTTLE/CHOKE CABLE ADJUSTMENT: Correct throttle cable adjustment allows for full range of motion on engine throttle body in conjunction with throttle control on handle dash. Correct choke cable adjustment engages choke when choke knob is pulled fully out. ...
Page 17 - ADJUST
GVTP SM32-R0303.1 5 maintenance (cont.) • BRAKE ADJUSTMENT: LOWER ROD - The brake assembly has been set at the factory. However, they may periodically need adjustment. As a rule of thumb, the bottom bend of the lower brake rod (3:14) should be 3/8” lower than the center of the pivot boss hole in the...
Page 18 - INCREASE
GVTP SM32-R0303.1 5 maintenance (cont.) • SIDE IDLER TENSION SPRING ADJUSTMENT: To increase tension, remove nut and lock washer securing rear spring hanger bolt (3:34) in middle tension hole, and replace bolt in uppermost hole. To decrease tension, replace in lowest hole. Replace lock washer and nut...
Page 19 - BLADE DECK GROUP
GVTP SM32-R0303.1 19 18 23 24 32" Cut Mower BLADE DECK GROUP SHEET 1 OF 4 R0303.1 15 12 12 13 15 14 16 41 5 10 9 8 11 17 21 26 6 7 25 20 A 29 A thru 44 22 32 27 31 30 25 28 3433 31 40 36 35 43 37 38 45 To Blade Pulley - See Engine & Trans Group 47 46 1 2 42 39 3 4 See Engine & Trans Grou...
Page 20 - Snapper 32” Cut Mower; SHEET 1 - BLADE DECK GROUP
GVTP SM32-R0303.1 Snapper 32” Cut Mower R0303.1 SHEET 1 - BLADE DECK GROUP REF # PART # QTY DESCRIPTION 1 3010260 1 Blade deck --- 3079166 1 Decal – ‘Operating Rules 1-8’ --- 3079090 2 Decal – ‘Danger – Keep Hands & Feet Away’ --- 3079088 1 Decal – ‘Danger – Flying Material’ --- 3079091 1 Decal ...
Page 21 - QTY
GVTP SM32-R0303.1 34 3031987 1 3/8-16 small serrated flange nut Snapper 32” Cut Mower R0303.1 SHEET 1 - BLADE DECK GROUP (cont.) REF # PART # QTY DESCRIPTION 35 3031410 1 3/8-16 x 2" carriage bolt 36 3031686 1 3/4" spacer bushing 37 3036120 1 Deck idler pulley 38 3032132 1 3/8-16 large serra...
Page 25 - SIDE IDLER & AXLE GROUP
GVTP SM32-R0303.1 1 32" Cut Mower SIDE IDLER & AXLE GROUP SHEET 3 OF 4 R0303.1 13 32 23 10 4 3 2 24 11 thru 20 18 17 15 14 9 8 A 28 26 25 27 19 16 12 7 6 5 See Engine & Trans Group 33 31 43 42 30 A 21 22 See Handle Group 34 41 36 37 35 29 37 35 38 40 39
Page 28 - HANDLE GROUP
GVTP SM32-R0303.1 32 14 See Engine & Trans Group See Side Idler & Axle Group 25 35 34 36 4 Cable goes thru #34 this page 1 16 30 32" Cut Mower HANDLE GROUP SHEET 4 OF 4 R0303.1 3 9 33 22 19 22a 5 7 6 20 21 8 23 24 2 17 11 18 31 1513 28 INDAK 26 27 29 IN D AK 10 12
Page 29 - SHEET 4 - HANDLE GROUP
GVTP SM32-R0303.1 Snapper 32” Cut Mower R0303.1 SHEET 4 - HANDLE GROUP REF # PART # QTY DESCRIPTION 1 3023511 1 Handle assembly --- 3032136 1 Mower dash overlay decal 2 3031283 2 Handle grip - 1"dia x 4-1/2" 3 3031122 4 1/2-13 x 1-1/4" hex bolt 4 3032130 4 1/2-13 serrated flange nut 5 30...
Page 30 - ALL SPECIFICATIONS SUBJECT TO CHANGE WITHOUT NOTICE
GVTP SM32-R0303.1 Snapper 32” Cut Mower R0303.1 SHEET 4 - HANDLE GROUP REF # PART # QTY DESCRIPTION --- 3031916 1 5” jumper wire – 1/4” female spade to bullet terminal – engine kill --- 3031864 2 8" wire tie (secures harness to handlebar) --- 3032149 1 Multi-lead ground wire – to PTO switch, saf...
