Snapper 1807-0 - Manual

6 Snapper 2300 PSI Pressure Washer 4. Insert the other “L” hook through the hole just abovethe billboard on the right side of the handle (viewingfrom rear of unit). Hold the hook in place with a pliersand attach the locknut with a 7/16” wrench (Figure 3). Add Engine Oil IMPORTANT: Any attempt to cra...

Snapper 2300 PSI Pressure Washer 7 • Attach the other end of the high pressure hose to the high pressure outlet on the pump (Figure 4). Tighten byhand. • Before you connect your garden hose to the water inlet, inspect the inlet screen (Figure 5). Clean the screen if itcontains debris or have it repl...

8 Snapper 2300 PSI Pressure Washer HOW TO USE YOUR PRESSURE WASHER If you have any problems operating your pressure washer,please call the pressure washer helpline at 1-800-317-7833. How to Start Your Pressure Washer To start your pressure washer for the first time, followthese instructions step-by-...

Snapper 2300 PSI Pressure Washer 9 How to Use the Adjustable Nozzle You now should know how to START your pressurewasher and how to STOP it. The information in thissection will tell you how to adjust the spray pattern and toapply detergent or other cleaning chemicals. WARNING! NEVER adjust spray pat...

10 Snapper 2300 PSI Pressure Washer • Make sure the garden hose is connected to the water inlet. Check that the high pressure hose is connected tothe spray gun and the pump. Start the engine. • Apply the detergent to a dry surface, starting at lower portion of area to be washed and work upward, usin...

Snapper 2300 PSI Pressure Washer 11 SPECIFICATIONS Outlet Pressure . . . . . 2300 psi Flow Rate . . . . . . . . . . 2.0 gallons per minute (gpm) Detergent . . . . . . . . . . Use detergent approved for pressure washers Water Supply . . . . . . Not to Exceed 100°F Temperature Automatic Cool . . . . W...

12 Snapper 2300 PSI Pressure Washer To remove contaminants from the pump, followthese steps: • Set up the pressure washer as described in “Preparing Pressure Washer For Use”. Connect the water supplyand turn water on. • Remove the nozzle extension from the spray gun. • Start the engine according to ...

Snapper 2300 PSI Pressure Washer 13 5. Using a garden hose, remove additional debris by backflushing water through the nozzle extension(Figure 15). Back flush between 30 to 60 seconds. Turnthe adjustable nozzle extension to stream spray andmove the nozzle from low to high while flushing. 6. Reinstal...

14 Snapper 2300 PSI Pressure Washer PREPARING THE UNIT FOR STORAGE Water should not remain in the unit for long periods oftime. Sediments or minerals can deposit on pump parts and“freeze” pump action. If you do not plan to use the pressurewasher for more than 30 days, follow this procedure: 1. Flush...

Snapper 2300 PSI Pressure Washer 15 TROUBLESHOOTING Problem Cause Correction Pump has following problems: failure to produce pressure, erratic pressure, chattering, loss of pressure, low water volume. 1. Nozzle in low pressure mode. 2. Water inlet is blocked. 3. Inadequate water supply. 4. Inlet hos...

16 Snapper 2300 PSI Pressure Washer EXPLODED VIEW AND PARTS LIST – MAIN UNIT Item Part # Description 1 192547GS BASE 2 B191874GS HANDLE 3 191909GS BILLBOARD 4 190249GS HOSE 5 192529GS KIT, Pump Mounting Hardware 6 192128GS KIT, Hook 7 190132GS GUN 8 B2203GS KIT, Handle Connector 9 192310GS KIT, Vibr...

Snapper 2300 PSI Pressure Washer 17 EXPLODED VIEW AND PARTS LIST — PUMP Item Part # Description 19 190571GS CAP, Oil 23 190626GS CARTER 28 190627GS MANIFOLD 29 190575GS O-RING 30 190576GS SCREW 34 190577GS CONNECTION, Chemical Inlet 45 190578GS PIN 46 190579GS VALVE, Seat Plate, Brass 47 190580GS VA...