Snapper 1726564 - Manual - manualsarea.com

Page 2 - Table of Contents; SPECIFICATIONS; WARNING

1 Table of Contents Initial Assembly & Installation Cart Assembly .................................................8Cover Assembly...............................................9 Normal Installation & Removal Installation .....................................................11Removal...........

Page 3 - SAFETY DECALS; GENERAL WARNINGS; ATTACHMENT DECALS

2 Safety Rules& Information Read these safety rules and follow them closely. Failure to obey these rules could result in loss of control ofunit, severe personal injury or death to you, or bystanders, or damage to property or equipment. The trian-gle in text signifies important cautions or warnin...

Page 4 - General; REQUIRED ACCESSORIES; AFTER OPERATION; STORING THE GRASS CATCHER

3 BEFORE OPERATION Clear the lawn of all sticks, stones, wire and other debriswhich may be caught or thrown by the mower blades. Check grass condition. If wet, wait until later in the day.If grass is wet, the grass catcher is likely to becomeplugged. For efficient bagging, air circulation under them...

Page 5 - Operation; MAINTENANCE; Cleaning Clear Tube; OPERATION; Dumping Grass and Leaves; Wheels

4 Operation MAINTENANCE Cleaning Clear Tube To clean the clear tube, wash with warm water and mildsoap or detergent. Use a soft, clean sponge or cloth.DO NOT use abrasive, alkaline, or petroleum basedcleaners. Cover The cover can be rinsed with a hose when dirty. A dirtycover will inhibit the fast f...

Page 6 - Notes

Page 8 - Reversible Frame Orientation

7 Offset Offset 3/4” 1-1/2” B Figure 4. Left Side DischargeA. Handle, Latch C. Frame B. U-Bracket, Hole 1-1/2” from edge Figure 5. Right Side DischargeA. Handle, Latch C. Frame B. U-Bracket, Hole 3/4” from edge. Reversible Frame Orientation For Left Side discharge locate the handle (A, Figure 4)on t...

Page 9 - CART ASSEMBLY

8 CART ASSEMBLY 1. Determine if you have a right side or left side dis- charge. Refer to Figures 4 & 5. 2. Install the wheel assemblies (A, Figure 6) to the frame (B). Place the head of the swivel wheel on theend of the frame. Align the holes and place four 3/8-16 x 1 hex bolts up through the fr...

Page 10 - Initial Installation & Assembly; COVER ASSEMBLY

9 Initial Installation & Assembly 6. Install support tube (A, Figure 10) inside the box. Align each end of the support tube with the two holesat the front corner side of the box. Place one 5/16-18x 1-1/2 hex bolt with a 5/16 flat washer and plasticspacer through the top, outside hole of the box ...

Page 11 - Initial Assembly & Installation

10 Initial Assembly & Installation 6. Install the sleeve clamp (C, Figure 15) to the connect- ing sleeve (A) with 1/4-20 x 1/2 slotted truss headscrew (D) and nyloc nut (E). Install the connectingsleeve inside the collar of the cover and positionsleeve clamp (C) over the support tube (B). 7. Thr...

Page 12 - NORMAL INSTALLATION & REMOVAL; Installation; Removal

11 Normal Removal & Installation NORMAL INSTALLATION & REMOVAL Installation 1. Insert the upper end of the clear tube into the cart sleeve. Slide the flex hose (C, Figure 20) over theturbo (A) and secure with the large hose clamp (B).The hose should overlap the turbo discharge by 2”-3”. The ...

Page 13 - Torque Specification Chart; Hardware Identification & Torque Specifications; Wrench & Fastener Size Guide

Torque Specification Chart FOR STANDARD MACHINE HARDWARE (Tolerance ± 20%) HardwareGrade SAE Grade 2 SAE Grade 5 SAE Grade 8 Size Of in/lbs in/lbs in/lbs Hardware ft/lbs Nm. ft/lbs Nm. ft/lbs Nm. 8-32 19 2.1 30 3.4 41 4.6 8-36 20 2.3 31 3.5 43 4.9 10-24 27 3.1 43 4.9 60 6.8 10-32 31 3.5 49 5.5 68 7....

Snapper 1726564 - Manual

Table of Contents:

Summary

Other Snapper Models