Snapper 1725580 - Manual - manualsarea.com

Page 2 - Table of Contents

1 Assemble Catcher Bags ..................................8 Install Cover .....................................................8 Removing & Reattaching the Triple Catcher Removing the Grass Catcher ..........................9 Reattaching the Grass Catcher .....................10 Storing the Gras...

Page 3 - SAFETY DECALS; GENERAL WARNINGS; ATTACHMENT DECALS; WARNING

2 Safety Rules& Information Read these safety rules and follow them closely. Failure to obey these rules could result in loss of control ofunit, severe personal injury or death to you, or bystanders, or damage to property or equipment. The trian-gle in text signifies important cautions or warnin...

Page 4 - General; REQUIRED ACCESSORIES; AFTER OPERATION; STORING THE GRASS CATCHER

3 BEFORE OPERATION Clear the lawn of all sticks, stones, wire and other debriswhich may be caught or thrown by the mower blades. Check grass condition. If wet, wait until later in the day.If grass is wet, the grass catcher is likely to becomeplugged. For efficient bagging, air circulation under them...

Page 5 - Install Hitch

4 Initial Hitch Installation - Models with out 3-Point Hitch Figure 1. Install Side BracketsA. Side Brackets E. Lockwashers, 1/2 B. Spacers F. Clevis Pins C. Nuts, 1/2-13 G. Safety Clips D. Capscrews, 1/2-13 x 2-1/2 A F Figure 3. Install Back PlateA. Hair Pin ClipB. Back PlateC. Hitch PinD. Lower Sp...

Page 7 - INITIAL INSTALLATION & ASSEMBLY; Assemble Front and Back Plate

6 INITIAL INSTALLATION & ASSEMBLY Assemble Front and Back Plate 1. For units with left side discharge use the set of holes on the right side of the back plate. For units with rightside discharge use the set of holes on the left side ofthe back plate. Attach the back plate (A, Figure 6 &7) to...

Page 8 - Initial Installation & Assembly; Assemble Tubes & Deflector

7 Initial Installation & Assembly Figure 8. Assemble Tubes & Deflector A B G G C D E I I J J K J H H L K K J M J A. DeflectorB. Back PlateC. Capscrew, 5/16-18 x 1 D. SocketE. Upper TubeF. Lower TubeG. Rubber Strap H. NutI. Capscrew, 1/4-20 x 1-1/4 J. Washer, 1/4K. HookL. Locknut, 5/16-18M. W...

Page 9 - Assemble Catcher Bags

8 Initial Installation & Assembly Assemble Catcher Bags See Figure 11. 1. Insert the wire hoop (H) through the cloth bag (B). 2. Install the clamp (E) and hanger bracket (D). Secure with two 5/16-18 x 3/4 carriage bolts (C), lockwashers(G), and nuts (F). Install Cover 1. See Figure 12. Hook the ...

Page 10 - REMOVING THE GRASS CATCHER

9 Removing & Reattaching Grass Catcher REMOVING THE GRASS CATCHER 1. Remove the hair pin clips (D, Figure 15) and hinge pins (B) and remove the cover (A). 2. Remove the bags (A, Figure 16) by lifting them off their hooks. Empty any grass out the bags. 3. Remove the long hitch pin (C, Figure 17, ...

Page 11 - Removing & Reattaching; Models with out 3-Point Hitch; Models with 3-Point Hitch

10 Removing & Reattaching REATTACHING THE GRASS CATCHER Models with out 3-Point Hitch 1. Set the front and back plate assembly on the pins (Figure 19). 2. Secure with the long hitch pin (C, Figure 19) Models with 3-Point Hitch 1. Set the front and back plate assembly on the clevis pins (Figure 2...

Page 13 - Torque Specification Chart; Hardware Identification & Torque Specifications; Wrench & Fastener Size Guide

12 Torque Specification Chart FOR STANDARD MACHINE HARDWARE (Tolerance ± 20%) HardwareGrade SAE Grade 2 SAE Grade 5 SAE Grade 8 Size Of in/lbs in/lbs in/lbs Hardware ft/lbs Nm. ft/lbs Nm. ft/lbs Nm. 8-32 19 2.1 30 3.4 41 4.6 8-36 20 2.3 31 3.5 43 4.9 10-24 27 3.1 43 4.9 60 6.8 10-32 31 3.5 49 5.5 68...

Snapper 1725580 - Manual

Table of Contents:

Summary

Other Snapper Models