Snapper 1685336 - Manual
Snapper 1685336 – Manual, read for free online in PDF format. We hope this helps you resolve any issues you may have. If you have further questions, please contact us through the contact form.
Table of Contents:
- Page 2 – Blade Tractor
- Page 3 – . Lower push bar and install dozer blade with kingpin
- Page 4 – Upper Cross Member; Actual Templates of Figure 3.
GENERAL
The Spring Assist Kit is used to retrofit the hitch used to
install the 42”
and 46” Snow Plow/Dozer Blade on
several different models (series) of tractors. For easier
understanding of this instruction sheet,
identify the
size of blade (42”
46”) and group of tractor on which
you are working. Follow these specifications throughout
the ten steps.
Tractors:
Group 1:
Group 2:
Group 3:
Group 4: 900, 7100
Snow Plow/Dozer
Blade:
42”
Mfg. No. 1690085 (Group 1, 2 tractors)
42”
Mfg. No. 1691520 (Group 3, 4 tractors)
46”
Mfg. No. 1~690088 (Group 3, 4 tractors)
IT
PARTS
Mounting location for 42” blade on Group 2 tractors
Use 0, 1, 2 or 4 links
Mounting location for 42” Group 1, 3 and 4 tractors
Mounting location for
46” blade on Group 3
4 tractors
Ref. Description
Part Number
A.
NUT, Hex Lock,
1
1923362
WASHER, Plain,
2 1919381
C.
1
1 9 2 1 9 7 7
D.
CHAIN,
1
1669241
E .
SPRING
1
1675232
INSTALLATION
INSTRUCTIONS
SPRING ASSIST KIT
MFG. NO. 1685336
INSTALLATION
1. Park tractor on a flat, level surface. Shut off engine,
remove key and apply parking brake.
2. Release lift handle so that dozer blade rests on the
ground.
3. Remove spring clip from king pin (A, figure 2).
Remove king pin and pivot pin (B) from push bar.
Slide dozer blade forward and
from push
bar.
4. Remove cotter pin
from rod guide(D). Remove
rod guide from hitch bracket
Push bar should
now be free to
up and down.
Figure 2. Dozer Blade Removal
A. King Pin
B. Pivot
C. Cotter Pin
D. Rod Guide
E. Hitch Bracket
5. Drill a hole in the bottom cross member (42” blade
on Group 1, 3 and 4 Series tractors) or
upper cross member (42” blade on Group 2 tractors)
according to the diagrams of the templates in
3. Actual templates are on a separate insert included
with these instructions.
For 46” blades on Group 3 and 4 tractors, drill a
hole in the (top) front plate. Hole should be located
left of centerline and
of the plate
rear edge. (Refer to figures 7E
1701916
1
IN U.S.A.
878
"Loading the manual" means you need to wait until the file loads and becomes available for online reading. Some manuals are very large, and the time they take to appear depends on your internet speed.
Summary
Figure 3. Diagrams of Hitch Templates 6. Assemble the chain (D, 1) to the tractor as follows: 42” Blade on Group 1 and 2 On left-hand side, remove and discard the upperself-tapping screws that holds bumper to frame.This is the hole used for installing chain in thefollowing steps, using 16-18 (C), tw...
Figure 7A. 4 2 ” Blade Group 1 Figure 76. 42” Blade Group 2 Member From Top Down Figure 7D. 42” Blade Group 4 Figure 7E. 46” Blade Group 3 Figure 7C. 42” Blade Group 3 Figure 7F. 46” glade Group 4 Figures 7A 7F. Spring Installation 8 . Lower push bar and install dozer blade with kingpin (A, spring c...
Upper Cross Member (42” blade Group 2) Dia. Bottom Cross Member Blade on Group 1, 3 4) Actual Templates of Figure 3. INSERT 1701016
