SMC EX250-SEN1 - Manual

SMC EX250-SEN1

SMC EX250-SEN1 – Manual, read for free online in PDF format. We hope this helps you resolve any issues you may have. If you have further questions, please contact us through the contact form.

1 Page 1
2 Page 2
3 Page 3
4 Page 4
5 Page 5
6 Page 6
7 Page 7
8 Page 8
9 Page 9
10 Page 10
11 Page 11
12 Page 12
13 Page 13
14 Page 14
15 Page 15
16 Page 16
17 Page 17
18 Page 18
19 Page 19
Page: / 19

Table of Contents:

  • Page 2 – C o n t e n t s; use so that you can operate this unit safely and correctly.; OPERATOR; this manual carefully and understand the contents.
  • Page 3 – SAFETY; IMPORTANT MESSAGES; Gives you helpful information.; NOTE; Otherwise injury or failure can result.; Do not operate beyond specification range.; Otherwise accident caused by malfunction can result.; Before performing maintenance:; Otherwise injury can result.; Handling precautions; Use the following UL-recognized DC power supply to combine with.
  • Page 4 – Product Summary; Up to 32 Inputs can be connected to the SI Unit using Input Blocks.; System configuration general
  • Page 5 – SI Unit Model Indication Method; Mounting/Installation; SI Unit body; Part Names; Communication protocol
  • Page 6 – Layout of the Input Block; Layout of the EX9 series Output Block / Power Block; Be sure to combine with the Power Block for use.; Position of End Plate; Output Block side) at the right end of the manifold.
  • Page 7 – Specifications; Basic specifications
  • Page 8 – Wiring; Communication wiring; Tighten the lock nut on cable side by turning it; Power supply wiring; Aligning the key groove with the
  • Page 9 – SI; Connecting one or two power supplies to SI Unit.; A. Two power supplies; Settings for display
  • Page 10 – Enable DHCP; Default settings; Switch setting
  • Page 11 – Input Block Model Indication Method; IE; Block type; Input Block
  • Page 12 – Input; Correlation between input number and Input Block; Input wiring
  • Page 13 – Install the Input Block after the setting; OE 1; Power supply type; Output specification; Display; EX9 Series Output Block/Power Block; Model Indication Method
  • Page 14 – Power Block; Output Block
  • Page 15 – Output connector pin layout; NC; Output wiring; Pin alignment and connection drawing of the Output Cable; Correlation between output number and Output Block
  • Page 16 – Ground; Pin alignment and connection drawing of the Power Supply Cable; Power Cable; Power Cable Jumper; Cable wiring
  • Page 17 – Option; Ethernet Communication Cable
  • Page 18 – Waterproof Cap; Check that the connected load does not exceed the; Overall system; Troubleshooting
  • Page 19 – EtherNet/IP compatible communication
Loading the manual

Reduced wiring system

EX250-SEN1

Instruction Manual

EtherNet/IP™ Compatible SI Unit

URL http:// www.smcworld.com

Specifications are subject to change without prior notice and any obligation on the part of the manufacturer.
EtherNet/IP™ is a trademark used under licence by ODVA.
The descriptions of products shown in this document may be used by the other companies as their trademarks.
© 2006 SMC Corporation All Rights Reserved

"Loading the manual" means you need to wait until the file loads and becomes available for online reading. Some manuals are very large, and the time they take to appear depends on your internet speed.

Summary

Page 2 - C o n t e n t s; use so that you can operate this unit safely and correctly.; OPERATOR; this manual carefully and understand the contents.

C o n t e n t s Thank you for purchasing the SMC reduced wiring system EX250 series. Please read this instruction manual carefully and understand the contents before use so that you can operate this unit safely and correctly. Please keep this manual handy for future reference. OPERATOR This instruct...

Page 3 - SAFETY; IMPORTANT MESSAGES; Gives you helpful information.; NOTE; Otherwise injury or failure can result.; Do not operate beyond specification range.; Otherwise accident caused by malfunction can result.; Before performing maintenance:; Otherwise injury can result.; Handling precautions; Use the following UL-recognized DC power supply to combine with.

2 3 SAFETY The body of unit and this manual contain the essential information for the protection ofusers and others from possible injury and property damage and to ensure correcthandling.Please check that you fully understand the definitions of the following messages( symbols ) before going on to re...

Page 4 - Product Summary; Up to 32 Inputs can be connected to the SI Unit using Input Blocks.; System configuration general

4 5 Product Summary Power supply for Output Block (for high wattage load)24VDC Connecting to bus at upper level(EtherNet/IP) Power supply for output/input and control24VDC Solenoid valve Output Block(for high wattage load) Power Block Output Block(for low wattage load) SI Unit applicable to EtherNet...

Other SMC Models

All SMC Other