Skylink LK-318-3 - Manual

1-Button Remote

2-Button Remote

3-Button Remote

Model LK-318-1

Model LK-318-2

Model LK-318-3

1-Button

Transmitter

LK-318-1

2-Button

Transmitter

LK-318-2

3-Button

Transmitter

LK-318-3

Buttons

Red

LED

1. INTRODUCTION

Thank you for your purchase of a SkylinkHome

TM

Remote, Model LK-

318-1/ LK-318-2 / LK-318-3. This remote which is also called transmitter

in this document allows you to wirelessly operate SkylinkHome

TM

receiver

modules.

All wireless signal communications within the SkylinkHome

TM

system are

based on rolling code technology to ensure highest security is used.

The following items are included in

this package:

- One of LK Series Remotes

- Lithium Battery CR-2032 (Installed)

- User’s Instructions

2. POWER UP

To power the transmitter, simply remove the battery isolator from the

transmitter, red LED will flash once. Press the button on the transmitter,

the red LED should flash. The transmitter is now powered properly. If

the red LED does not flash when button is pressed, refer to Section 6

“Battery” of this manual.

1) Remove isolator,

2) LED on for 1 second

3. PROGRAMMING TRANSMITTERS TO RECEIVER MODULE

In order to operate the receiver module remotely with a transmitter, it

must be programmed to the receiver module.

To program a remote to the receiver module, a “Learn” code must be

transmitted, follow the instructions below to transmit the “Learn” code

to the receiver.

1. Put the receiver module that you plan to program into programming

mode. Refer to the User’s Instructions of that receiver module.

2. Press 1 and 2 simultaneously and hold for 2 seconds until the LED

changes from on to flashing quickly. Release the buttons. The red

LED on the transmitter will be on for 15 seconds.

3. Press the button on the remote that you plan to use when the LED is

steadily on to transmit the “Learn” code.

4. Once the remote is programmed, the receiver modules will quit from

programming mode and the programmed transmitter is ready to be

used now.

Learn Code

Follow steps 2 and 3 above to transmit the “Learn” code when

programming the remote to receiver modules.

You may follow the same instructions to program different buttons on the

transmitter to different receiver modules.

LED on for

1 second

4. ON / OFF OPERATION

Pressing the programmed button on the transmitter once will toggle

the status of the load that is connected to the receiver module, i.e. if the

light is off, pressing the button turns on the light, and vice versa.

When the programmed button is pressed, the red LED flashes briefly

indicating signal is transmitting.

5. ADVANCED FEATURE - PASSWORD PROTECTION

Password protection (Only available for LK-318-3 (Not available for

LK-318-1 or LK-318-2)

The LK-318-3 can be password protected. If you enable the password

protection, you can only operate LK-318-3 after you input the correct

password.

Password can be 2-8 digits long, which is a combination of 1, 2 and 3. For

example, password can be 1, 2, 1, 2. To input this password, you have to

press button [1], then [2], then [1], then [2].

Note:

[1] = Button 1 [2] = Button 2 [3] = Button 3

Note:

The time-out period is 1 second during above password input.

The factory default password is 2, 2, 2, and this password function is

disabled out of factory.

Change password

1. Press 1 and 3 simultaneously and hold for more than 10 seconds

until the LED changes from flashing quickly to flashing slowly.

2. Input old password.

3. Press 1 and 3 once simultaneously to confirm. If the password is

wrong, the LED will flash 3 times and you have to start it over from

step1.

4. Input new password.

5. Press 1 and 3 once simultaneously to confirm.

6. Input new password again.

7. Press 1 and 3 once simultaneously to RE-confirm. If the password is

different from the one of step 4, the LED will flash 3 times and you

have to start over from step 1. Otherwise, the password has been

changed to the new one and the password protection is enabled.

Disable password

1. Press 1 and 3 simultaneously and hold for more than 5 seconds

until the LED flashes quickly but not until the LED flashes slowly.

2. Input old password.

3. Press 1 and 3 once simultaneously to confirm. If the password is

the password protection will be disabled.

Enable password

1. Press 1 and 3 simultaneously and hold for more than 2 seconds

until the LED flashes quickly but not until the LED flashes slowly.

2. Input old password.

3. Press 1 and 3 once simultaneously to confirm. If the password is

correct, the password protection will be enabled.

You can toggle the two states - password protection enabled or

disabled.

Note:

The time-out period is 15 seconds during any of the above setting opera-

tions. After 10 seconds, the LED will flash 3 times and the remote will exit

from setting.

Remove

isolator

Button [1]

Button [2]

Button [3]