Skylink HA-300 - Manual

The sensors must be programmed to the Household Alert

®

Long Range

Receiver before they can communication. You may program the sensors

to one of the 4 zones. Follow the instructions below:

1. Plug in an AC adapter to the receiver.

2. The green LED will be on indicating it is turned on.

3. Open the back cover and there is a learn button. Press and hold this

learn button for 5 seconds, until both green LED and zone 1 red LED

You may now release the learn button.

4. If you would like to program the sensor to zone 1, activate the

sensor while the zone 1 red LED is

Press the SET button

on the back of the sensor to activate it.

5. If you would like to program the sensor to other zones, press the

learn button again, until the red LED

at the zone you want to

program the sensor to, then activate the sensor.

6. Once the sensor is programmed, the green LED will be steadily on

and none of the red zone LEDs will be on.

Note: Each zone can program up to 4 sensors. If you try to program a

sensor into a zone, the

programmed sensor will be erased.

You cannot erase a

sensor. You must erase all sensors from

the receiver, then program the ones you would like to keep. To erase

all the sensors from the receiver:

1. Remove the adapter from the receiver.

2. Open the back cover, press and hold the learn button. Do not

release the learn button until step 4.

3. While holding onto the learn button, plug in the adapter to the receiver.

4. You may release the learn button when the LEDs on the receiver are on.

5. You have erased all sensors from the receiver.

1. INTRODUCTION

Deluxe Motion Monitoring Kit

Model

HA-300

The Deluxe Motion Monitoring Kit is designed to monitor movement around

your house. The motion sensor can be placed either indoor or outdoor. Once

In this package, you should

two Indoor/Outdoor Motion Sensors, a

Household Alert

®

Long Range Receiver, an adapter, two ball-head

joint

and screws.

Please follow the instructions below to setup your motion sensors and

the receiver.

Adapter

4 pcs 3 x 18 screws

(Included)

2 x Indoor/Outdoor

Motion Sensor

2x Ball-head joint

Plug in the adapter to the receiver

Insert 9V alkaline battery (option) to the sensor

2. PROGRAMMING

3. INSTALLATION

A ball-head joint is necessary to mount the sensor at a desire location.

A height of 7 ft is recommended, depending on your application. Once a

location is selected, mount the ball-head joint to this location by screws

provided. Once the ball-head joint is mounted to the wall, slide the back

of the sensor into the ball-head joint. The mounting angle can be

adjusted. Please refer to “Walk Test” to determine the best mounting

angle.

After mounting the sensor at the desired location, it is

important to perform a walk test in order to determine

if the sensor is detecting the things you want to detect.

In order to control how far the sensor can “see”, this can be done by

adjusting the angle of the sensor. To reduce the detection range, simply

move the sensor downward. To increase the range, move the sensor

up to around 12 degrees. This will give the maximum range. However,
this may not be desired if the sensor is placed outdoors, since

a false

trigger may occur if the sensor is set to detect motion in a distance.

You should walk in the area that you would like the sensor to monitor.

Place the slide switch on the side of the receiver to “Alert” position. The

receiver will beep if the sensor detects your movement. If the receiver

does not respond, adjust the mounting angle accordingly. After motion is

detected once, the sensor will not be triggered unless no motion is

detected for 20 seconds. Therefore, wait for at least 20 seconds during

walk testing between 2 activations.

Perform walk test in the undesired area to ensure movement cannot be

detected.

Household Alert

®

Long Range Receiver

SET Button

7 ft

Tips: The sensor should not face towards direct sunlight, placing near

heat or cold producing devices (i.e. A/C or furnance vents, fans, ovens,

heaters etc.) that may cause false triggers.

Move the sensor downward to

reduce the range.

Move the sensor up to around

12 º to give maximum range.

The sensitivity of the motion sensor is adjustable. Change the setting by

placing the connector on either the ”High” (connector position “1”) or

“Low” (connector position “2”) position. When the sensitivity is set to

“Low”, more movement is required to trigger the sensor. It is recom-

mended to set the sensitivity to “Low” and perform a “Walk Test”. If the

walk test result is

the sensitivity does not require to be

adjusted further. If the walk test

result shows the sensitivity is too

low, then you can change the

sensitivity setting to “High”. Please

perform the walk test after changing

the sensitivity setting.

1 - High 2 - Low

Learn Button

Page 1 of 2

Erasing a sensor

MOUNTING

WALK TEST

SENSOR SENSITIVITY