Skylink AD-1010 - Manual

1. Enter the current MPI N (Master Personal Identification Number)

on the SC-001.

2. Press [B].
3. Press the number key to identify which zone to add the panic

transmitter to. The keychain transmitter is designed to be pro-

grammed in zone 5 for SC-001 . Do not program the keychain

transmitter to zone 1,2,3,4. Therefore, press [5] for SC-001.

4. Press [ ] within 8 seconds.
5. Activate the keychain transmitter by pressing one of the buttons

on the transmitter. You will hear a long beep from the control panel,
and the keychain transmitter will now communicate to that zone.

Program the Keychain Transmitter (4B-434) to the
Security Control Panel (SC-001)

1. Press [L], [5] when in clock mode, the display will show

“L5 Id codE”.

2. Activate the keychain transmitter within 5 seconds by

pressing any button on the transmitter. The red LED
light of the transmitter will be on when the button is
pressed. The display will return to clock mode once the
keychain transmitter has bee n learned.

3. If the panic button of the keychain transmitter is pressed,

it will trigger the Emergency Dialer and start dialing preset
phone numbers (refer to AD-1010 User’s Instruction).

Program the Keychain Transmitter (4B-434)
to the Emergency Dialer (AD-1010)

Introduction

The Keychain Transmitter (4B-434)
conveniently fits on any keychain.
It allows you to arm and disarm the
S e c u r i t y C o n t r o l P a n e l
SC-001 and activate the
Emergency Dialer AD-1010 from
a maximum distance of
approximately 100 feet from the
unit. It has a panic button that
lets you remotely activate the
siren or dialer instantly.

Operation for Emergency Dialer (AD-1010)

T h e k e y c h a i n t r a n s m i t t e r ( 4 B - 4 3 4 ) c a n b e u s e d t o
c o n t r o l t h e Emergency Dialer AD-1010. The function
of buttons #1, #2, #3 are the same as the functions
as T1, T2, T3 on the keypad o f t he Emergency Dialer.
When one of these buttons are pressed, the dialer will
dial the stored phone number in the one-touch memory
(T1 or T2 or T3). The panic button on the transmitter
works the same as the panic button on the keypad of
the Emergency Dialer. It activates the dialer immedi-
ately and dials the preset emergency phone
numbers. Refer to the User’s Instruction of the
Emergency Dialer AD-1010 for details.

*

Operation for Control Panel (SC-001)

To arm the system using the keychain transmitter:
There are 2 different arm options to choose from:
1. Press button #1, and the Control Panel will beep once.

The system will be armed in the Away Sequence. This sequence arms the system when you are the last person leaving the premises.
(refer to SC-100 User’s Instruction for details)
Pressing button #1 will give you the same result as pressing: MPIN, [B], [C] on the keypad.

2. Press button #2, and the Control Panel will beep once.

The system will be armed in Home Sequence. It arms the system when someone remains in the premises. (refer to SC-100 User’s
Instruction for details)
Pressing button #2 will give you the same result as pressing: MPIN, [C] on the keypad.

To disarm the system using the keychain transmitter:
When the system is armed, press button #3. The red light on the transmitter flashes and the Control Panel beeps twice. The system is
now disarmed.
To deactivate the siren using the keypad transmitter:
Press and hold button #3, the red light on the transmitter flashes and the siren is deactivated.

Warranty

If, within one year from date
of purchase, this product
should become defective
(except battery), due to
faulty workmanship or
materials, it will be repaired
or replaced, without charge.
Proof of purchase is
required.

Operation for Control Panel (SC-001 )

FCC

WARNING:

Changes or modifications
to this unit not expressly
approved by the party res-
ponsible of compliance
could void the user’s
authority to operate the
equipment.

The Remote Control is
approved by the FCC and
it complies with Part 15
of the FCC Rules. Its
operation is subject to the
following two conditions :
1. This device may not

cause harmful inter-
ference.

2. This device must accept

any interference that
may cause undesired
operation.

Note: It doesn’t matter what mode you are in or even if
the system is off, once the panic button (the large red
button) is pressed, the siren comes on instantly.

Battery

The Keychain Transmitter operates on a 12
volt alkaline battery which is installed at the
factory. There are two screws on the back of
the transmitter that hold the top and bottom
cases together.
To replace the Keychain Transmitter battery:
1. Undo the two screws on the back of the

transmitter.
The bottom case will then come off.

2. Using a small screwdriver or pen, pry out

the old battery from one end.

3. Place the new battery in position. A

diagram beside the battery well indicates
which end is positive and which is negative.

4. Close the battery cover and reinsert two
screws.

+

-

B u t t o n 3

B u t t o n 1

B u t t o n 2

Panic Button

KEYCHAIN TRANSMITTER

USER'S INSTRUCTIONS

(Model 4B-434)

® are registered trademarks of their

respective corporations

®

NOTE

Skylink will not be held
liable or responsible for
any misuse or application
of this product other than
for its intended use.

I f you would like to order Skylink’s
product or have difficulty getting
them to work, please :
1. visit our website FAQ section at

www.skylinkhome.com , or

2. email us at

[email protected] , or

3. call our toll free at 1-800-304-1187

from Monday to Friday, 9 am to
5 pm EST.
fax: 1-800-286-1320

CUSTOMER SERVICE

17 Sheard Avenue, Brampton,
Ontario, Canada L6Y 1J3
Email:[email protected]
http://www.skylinkhome.com
P/N. 101A094-001
US Patent 6243000B1
©2004 SKYLINK GROUP