Sirius Satellite Radio DEH-P6700MP - Manual

Information to User Alteration or modifications carried out withoutappropriate authorization may invalidate theuser s right to operate the equipment. For Canadian model This Class B digital apparatus complies withCanadian ICES-003. About this unit The tuner frequencies on this unit are allo- cated f...

After-sales service for Pioneer products Please contact the dealer or distributor from where you purchased this unit for after-sales service (including warranty conditions) or any other information. In case the necessary infor- mation is not available, please contact the companies listed below: Plea...

Removing the front panel 1 Press OPEN to open the front panel. 2 Grip the left side of the front panel and pull it gently outward. Take care not to grip it too tightly or to drop the front panel and protect it from contact with water or other fluids to prevent perma- nent damage. Attaching the front...

Use and care of the remote control Installing the battery Slide the tray out on the back of the remote control and insert the battery with the plus (+) and minus ( ) poles pointing in the proper di- rection. WARNING Keep the battery out of the reach of children.Should the battery be swallowed, immed...

Head unit 1 CLOCK button Press to change to the clock display. 2 PAUSE button Press to turn pause on or off. 3 DISPLAY button Press to select different displays. 4 FUNCTION button Press to select functions. 5 AUDIO button Press to select various sound quality con- trols. 6 ENTERTAINMENT button Press...

Turning the unit on % Press SOURCE to turn the unit on. When you select a source the unit is turned on. Selecting a source You can select a source you want to listen to. To switch to the built-in CD player, load a disc in the unit (refer to page 18). % When using the head unit, press SOURCE to selec...

Notes ! The built-in CD player plays one, standard, 12-cm or 8-cm (single) CD at a time. Do not usean adapter when playing 8-cm CDs. ! Do not insert anything other than a CD intothe CD loading slot. ! There is sometimes a delay between startingup CD playback and the sound being issued.When being rea...

Listening to the radio 5 2 1 4 3 These are the basic steps necessary to operate the radio. More advanced tuner operation is explained starting on the next page. 1 Stereo (ST) indicator Shows that the frequency selected is being broadcast in stereo. 2 LOC indicator Shows when local seek tuning is on....

Playing a CD 2 1 These are the basic steps necessary to play a CD with your built-in CD player. More ad- vanced CD operation is explained starting on this page. 1 Track number indicator Shows the track currently playing. 2 Play time indicator Shows the elapsed playing time of the cur- rent track. 1 ...

! TRACK Repeat just the current track Note If you perform track search or fast forward/re-verse during TRACK , the repeat play range changes to DISC . Playing tracks in a random order Random play lets you play back tracks on the CD in a random order. 1 Press FUNCTION to select Random. Press FUNCTION...

Using compression and BMX Using the COMP (compression) and BMX functions let you adjust the sound playback quality of this player. Each of the functions have a two-step adjustment. The COMP func- tion balances the output of louder and softer sounds at higher volumes. BMX controls sound reverberation...

2 Press FUNCTION and hold until TITLE appears in the display. # When playing a CD TEXT disc, you cannot switch to TITLE . The disc title will have already been recorded on a CD TEXT disc. 3 Press button 1 to select the desired character type. Press button 1 repeatedly to switch between the following...

Displaying titles on CD TEXT discs % Press DISPLAY. Press DISPLAY repeatedly to switch between the following settings: Play time Disc Title (disc title) DiscArtist Name (disc artist name) Track Title (track title) TrackArtist Name (track artist name) # If specific information has not been recorded o...

Introduction of advanced built-in CD player (MP3/ WMA/WAV) operation 1 1 Function display Shows the function status. % Press FUNCTION to display the function names. Press FUNCTION repeatedly to switch be- tween the following functions: Repeat (repeat play) Random (random play) Scan (scan play) Pause...

3 Press a to turn scan play on. Scan :ON appears in the display. The first 10 seconds of each track of the current folder (or the first track of each folder) is played. 4 When you find the desired track (or folder) press b to turn scan play off. Scan :OFF appears in the display. The track (or folder...

2 Press c or d to select the search meth- od. Press c or d until the desired search method appears in the display. ! FF/REV Fast forward and reverse ! ROUGH SEARCH Searching every 10 tracks Searching every 10 tracks in the current folder If the current folder contains over 10 tracks, you can search ...

Scanning CDs and tracks While you are using DISC , the beginning of each track on the selected disc plays for about 10 seconds. When you are using MCD , the be- ginning of the first track of each disc is played for about 10 seconds. 1 Select the repeat range. Refer to Repeating play on the previous ...

4 Press a to store the currently playing track in the playlist. ITS Input is displayed briefly and the currently playing selection is added to your playlist. The display then shows ITS again. 5 Press BAND to return to the playback display. Note After data for 100 discs has been stored in mem-ory, da...

2 Press FUNCTION and hold until TITLE appears in the display, then press FUNCTION to select ITS. After TITLE is displayed, press FUNCTION until ITS appears in the display. 3 Press b to erase all tracks on the cur- rently playing CD from your ITS playlist. All tracks on the currently playing CD are e...

! After data for 100 discs has been stored inmemory, data for a new disc will overwrite theoldest one. Displaying disc titles You can display the title of any disc that has had a disc title entered. % Press DISPLAY. Press DISPLAY repeatedly to switch between the following settings: Play time Disc Ti...

Note When Ever Scroll is set to ON at the initial setting,CD text information scrolls continuously in thedisplay. If you want to display the first 16 charac-ters of text information temporarily and scrollfrom the beginning, press and hold DISPLAY . About Ever Scroll, refer to Switching the Ever Scro...

Introduction of audio adjustments 1 1 Audio display Shows the audio adjustments status. % Press AUDIO to display the audio func- tion names. Press AUDIO repeatedly to switch between the following audio functions: Fad (balance adjustment) EQ (equalizer curve adjustment) Bass (bass and treble level ad...

# When the rear output setting is REAR SP :S/W , you cannot adjust front/rear speaker balance. Refer to Setting the rear output and subwoofer controller on page 42. 3 Press c or d to adjust left/right speaker balance. When you press c or d , Bal L/R 0 is dis- played. Each press of c or d moves the l...

Fine-adjusting equalizer curve You can adjust the center frequency and the Q factor (curve characteristics) of each currently selected curve band ( EQ LOW / EQ MID / EQ HIGH ). Level (dB) Center frequency Q=2N Q=2W Frequency (Hz) 1 Press AUDIO and hold until frequency and the Q factor (e.g., F 80 Q ...

Selecting bass frequency You can select the bass frequency for level ad- justment. 1 Press AUDIO and hold until frequency and the Q factor (e.g., F 80 Q 1W) appears in the display. 2 Press AUDIO to select Bass. Press AUDIO until Bass appears in the dis- play. 3 Press c or d to select the desired fre...

Adjusting subwoofer settings When the subwoofer output is on, you can ad- just the cut-off frequency and the output level of the subwoofer. 1 Press AUDIO to select Sub-W2. Press AUDIO until Sub-W2 appears in the dis- play. # You can also select the subwoofer setting menu by pressing SW on the unit. ...

Only frequencies higher than those in the se- lected range are outputted from the front or rear speakers. Adjusting source levels SLA (source level adjustment) lets you adjust the volume level of each source to prevent ra- dical changes in volume when switching be- tween sources. ! Settings are base...

Adjusting initial settings 1 Initial settings lets you perform initial setup of different settings for this unit. 1 Function display Shows the function status. 1 Press SOURCE and hold until the unit turns off. 2 Press FUNCTION and hold until the clock appears in the display. 3 Press FUNCTION to sele...

1 Press FUNCTION to select AUX. Press FUNCTION repeatedly until AUX ap- pears in the display. 2 Press a or b to turn AUX on or off. Pressing a or b will turn AUX on or off and that status will be displayed (e.g., AUX :ON ). Switching the dimmer setting To prevent the display from being too bright at...

Notes ! Even if you change this setting, there is nooutput unless you turn the nonfading output(refer to Using nonfading output on page 39) or subwoofer output (refer to Using subwoofer output on page 38) in the audio menu on. ! If you change the subwoofer controller, sub-woofer output and nonfading...

Using the operation mode 2 Switching to operation mode 2 enables you to operate the basic functions for each source easily. ! However, it may not possible to operate every function for each source with opera- tion mode 2. Switch the operation mode to 1 to operate a function that does not corre- spon...

Button Operation DISPLAY No function. FUNCTION No function. Television Button Operation PAUSE Press to turn loudness on or off. AUDIO Press and hold to turn best stations se- quential memory on. Press to turn best stations sequential memory off. DISPLAY Press to quickly lower the volume level, by ab...

1 After you have selected AUX as the source, press FUNCTION and hold until TITLE appears in the display. 2 Press button 1 to select the desired character type. Press button 1 repeatedly to switch between the following character types: Alphabet (upper case) Alphabet (lower case) European letters, suc...

Introduction of XM operation 5 2 1 4 3 You can use this unit to control a XM satellite di- gital tuner (GEX-P910XM), which is sold separately. For details concerning operation, refer to the XMtuner s operation manuals. This section provides information on XMoperations with this unit which differs fr...

For details concerning operation, refer to the DVD player s or multi-DVD player s operation manual. This section provides information on DVD operations with this unit which differs from that described in the DVD player s or multi-DVD player s operation manual. Operation You can use the following fun...

Understanding built-in CD player error messages When you contact your dealer or your nearest Pioneer Service Center, be sure to record the error message. Message Cause Action ERROR-11, 12, 17, 30 Dirty disc Clean disc. ERROR-11, 12, 17, 30 Scratched disc Replace disc. ERROR-10, 11, 12, 15, 17, 30, A...

! Some audio CDs contain tracks that merge into one another without a pause. When these discs are converted to MP3/WMA/ WAV files and burned to a CD-R/CD-RW/ CD-ROM, the files will be played back on this player with a short pause between each one, regardless of the length of the pause between tracks...

About folders and MP3/ WMA/WAV files ! An outline of a CD-ROM with MP3/WMA/ WAV files on it is shown below. Subfolders are shown as folders in the folder currently selected. 1 2 3 1 First level 2 Second level 3 Third level Notes ! This unit assigns folder numbers. The usercan not assign folder numbe...

Terms Bit rate This expresses data volume per second, or bps units (bits per second). The higher the rate, the more information is available to reproduce the sound. Using the same encoding method (such as MP3), the higher the rate, the better the sound. ID3 tag This is a method of embedding track-re...

Specifications General Power source ............................. 14.4 V DC (10.8 15.1 V al- lowable) Grounding system ................... Negative type Max. current consumption ..................................................... 10.0 A Dimensions (W × H × D): DIN Chassis ..................... 178...

PIONEER CORPORATION 4-1, MEGURO 1-CHOME, MEGURO-KU, TOKYO 153-8654, JAPAN PIONEER ELECTRONICS (USA) INC. P.O. Box 1540, Long Beach, California 90801-1540, U.S.A. TEL: (800) 421-1404 PIONEER EUROPE NV Haven 1087, Keetberglaan 1, B-9120 Melsele, Belgium TEL: (0) 3/570.05.11 PIONEER ELECTRONICS ASIACEN...

Subwoofer output ornon fading output Antenna jack This product Front output Fuse IP-BUS input (Blue) Connecting cords with RCA pinplugs (sold separately) System remote control Front speaker Front speaker Left Right Perform these connections when using theoptional amplifier. + ≠ + ≠ + ≠ + ≠ + ≠ + ≠ Y...

Removing the unit (Fig. 6) (Fig. 7) Fig. 6 Fig. 7 To remove the frame, extend top andbottom of the frame outwards inorder to unlock it. (When reattachingthe frame, point the side with agroove downwards and attach it.)• It becomes easy to remove the frame if the front panel is released. Insert the su...

DIN Rear-mount Installation using the screw holes on the side of the unit 1. Remove the frame. (Fig. 8) Fig. 8 2. Fastening the unit to the factory radio mounting bracket. (Fig. 9) (Fig. 10) Select a position where the screw holes of the bracket andthe screw holes of the head unit become aligned (ar...