Simplicity Turbo Wide Body Cart & Hitch - Manual

Page 3 - TABLE OF CONTENTS; Table of Contents; SPECIFICATIONS; WARNING

TABLE OF CONTENTS SPECIFICATIONS ........................................................1 ILLUSTRATIONS & PART LISTS ................................2 Wide Body Dump Cart .......................................................2Tube Assembly (SunStar & Sovereign) ...............................

Page 4 - Illustrations & Part Lists

Figure 1. Wide Body Dump Cart 2 Illustrations & Part Lists No. Qty. Description 1 1 COVER 2 1 ROD, Straight 3 2 CLIP, Safety, Hairpin 4 1 SLEEVE, Plastic, Connecting 5 1 CLAMP, Sleeve 6 1 TUBE, Support 7 2 HANDLE, Lift 8 4 LOCKWASHER, 1/4 9 4 NUT, Hex, 1/4-20 10 4 NUT, Lock, 5/16-18 11 6 WASHER,...

Page 7 - Safety Rules; SAFETY RULES

5 Safety Rules SAFETY RULES 1. Know the tractor controls and how to stop quickly. READ THE TRACTOR'S OWNER'S MANUAL. 2. Shut the engine off before attaching, adjusting, or dis- connecting the Collection System. 3. Check the cart to make sure it is attached tightly to tractor. 4. Check the latch hand...

Page 8 - Cart Assembly; CART ASSEMBLY

6 Cart Assembly CART ASSEMBLY 1. Install the wheel assemblies (A, Figure 8) to the frame (B). Place the head of the swivel wheel on theend of the frame. Align the holes and place four 3/8-16 x 1 hex bolts up through the frame and head ofthe swivel. Secure with four flat washers (13/32 I.D.,7/8 O.D.)...

Page 9 - Cover Assembly; COVER ASSEMBLY

7 Cover Assembly 5. Install support tube (A, Figure 12) inside the box. Align each end of the support tube with the two holesat the front corner side of the box. Place one 5/16-18x 1-1/2 hex bolt with a 5/16 flat washer and plasticspacer through the top, outside hole of the box andthe support tube. ...

Page 11 - Hitch Installation; HITCH INSTALLATION

9 Hitch Installation Figure 22. Sunstar Hitch InstallationA. U-Bracket D. Bracket B. Capscrew, 1/2-13 x 1-1/4 E. Large HoleC. Capscrew, 7/16-14 x 1/2 F. Capscrew, 7/16-14 x 1/2 Figure 23. Sovereign Hitch InstallationA. Locknut, 1/2-13 F. Support Bracket B. U-Bracket G.Capscrew, Hex, 1/2-13x1-1/2 C. ...

Page 13 - Discharge Tube Installation; DISCHARGE TUBE INSTALLATION

11 Discharge Tube Installation DISCHARGE TUBE INSTALLATION Landlord/1700 Series (Mfg. No. 1692526)Broadmoor/1600 Series (Mfg. No. 1692526) 1. Install the spring clip (D, Figure 26) with two 10/32 x 1/2 truss head screws (E), four flat washers (F), andtwo locknuts (G). 2. Install 1/4-20 x 5/8 carriag...

Page 14 - Connecting Cart / Maintenance; CONNECTING CART TO TRACTOR; Cleaning Clear Tube

12 Connecting Cart / Maintenance Figure 28. Connecting Cart To TractorA. Cart Frame C. Spring Clip B. Clevis Pin CONNECTING CART TO TRACTOR Place the cart frame (A, Figure 28) onto tractor bracketsand install the clevis pins (B) and springs clips (C). MAINTENANCE Cleaning Clear Tube To clean the cle...

Page 15 - Operation; CAUTION; OPERATION; Before Operation

13 Operation Figure 30. Emptying the Cart CAUTION The maximum weight capacity of the cart is 400lbs. Do not exceed. OPERATION Before Operation Clear the lawn of all sticks, stones, wire and other debriswhich may be caught or thrown by the mower blades. Clean the tube with mild detergent (other produ...

Page 16 - Operating Without Collection System; Reinstallation After Removal

14 Operation Operating Without Collection System 1. Unhook the cart from the tractor by removing two cle- vis pins and spring clips (Figure 28). 2. To remove the blower, remove the belt from the pul- ley (A, Figure 31). 3. Close cover (D) and tighten knob. 4. Loosen wing nut (B) and, while holding d...

Page 17 - Torque Specification Chart; Hardware Identification & Torque Specifications; Wrench & Fastener Size Guide

Torque Specification Chart FOR STANDARD MACHINE HARDWARE (Tolerance ± 20%) HardwareGrade SAE Grade 2 SAE Grade 5 SAE Grade 8 Size Of in/lbs in/lbs in/lbs Hardware ft/lbs Nm. ft/lbs Nm. ft/lbs Nm. 8-32 19 2.1 30 3.4 41 4.6 8-36 20 2.3 31 3.5 43 4.9 10-24 27 3.1 43 4.9 60 6.8 10-32 31 3.5 49 5.5 68 7....

Page 18 - Notes