Page 2 - CHART
HEX CARRIAGE BOLT PLAIN WASHER LOCKWASHER NUT HEX Shown below are actual size heads for standard screw sizes.Example: a screw has head and thus requires a w r e n c h . T o m e a s u r e l e n g t h , u s e t h e s c a l e b e l o w . Head Head screw with screw with SD. 7ll6’S.D. Head Head Head scre...
Page 3 - S E E
TORQUE SPECIFICATIONS FOR STANDARD MACHINE HARDWARE S E E SAE GRADE 0 N m . Nm. Nm. 8-32 19 2.1 8-38 2 0 2.3 2 7 3.1 3 1 3.5 6 6 7.8 7 8 8.8 15. 12 18.3 2 0 27.231.340.8 3 5 47.8 5 0 8 8 . 55 74.8 8 5 88.4 7 5 102. 1 9 0 122.4 100 138. 0 180 2 1 7 . 8 8 180 2 4 4 . 8 140 190.4 4 155 210.8 l-8 2 2 0 ...
Page 5 - TABLE OF CONTENTS
TABLE OF CONTENTS SECTION S a f e t y R u l e s PAGE Safe Operation Practices and Precautions ..................................................................................................... S a f e Operation of Snowthrower.. ........................................................................
Page 6 - RULES; Safe Operation Practices and Precautions
RULES Safe Operation Practices and Precautions Product knowledge and careful operation is the best way to prevent accidents. Read this section carefully beforeoperating attachment system. All operators, no matter how much experience they may have, should read this and other related manuals before op...
Page 7 - Safe Maintenance and Storage
8. Never attempt to make any adjustments while the engine is running (except when specifically recom- mended by manufacturer). 9. Let engine (motor) and machine adjust to outdoor temperatures before starting to clear snow. Always wear safety glasses or eye shields during operation or while performin...
Page 8 - SAFETY DECALS
SAFETY DECALS T h e f o l l o w i n g s a f e t y l a b e l s a r e l o c a t e d o n y o u r t r a c t o r a ss h o w n . TO PREVENT SERIOUS INJURY, CAREFULLY READAND FOLLOW THESE WARNING INSTRUCTIONS ATAU TIMES. THIS DECAL MUST BE POSITIONED SO AS TOBE EASILY READ FROM THE FRONT OF THES N O W T H ...
Page 9 - PARTS IDENTIFICATION
PARTS IDENTIFICATION TOOLS NECESSARY FOR INSTALLATION AND ASSEMBLY: O n e ( 1 ) W r e n c h Two (2) Wrench One (1) Allen Wrench Note: Right and left hand sides are determined by facing forward in the tractor seat. A U G E R S H E A RB O L T LEVEL CHECK PLUG CUTTING EDGE SHEAR BOLT SUPPORT S P R I N ...
Page 10 - INSTALLATION; Tractor Preparation; Chute Rotator Bracket
INSTALLATION Tractor Preparation 1. Increase the front tire pressure to 20 PSI for use with snowthrower. 2. On tractors with Kohler Magnum engines, loosen the air cleaner cover wing nut, pull intake hose out ofplenum hole and rotate cover slightly. For winteroperation only, this allows warmer air to...
Page 11 - Lift Rod; Install Discharge Chute
Lift Rod 1. Lay lift rod (A, figure 3) next to the tractor so that rear (B) with square weldment (C) is towards the r e a r . T h e w e l d m e n t i s p o s i t i o n e d t o p r e v e n t c l e v i s p i n(D) from being installed from the right hand side( i n t e r f e r e n c e w o u l d o c c u ...
Page 13 - M o u n t i n g S n o w t h r o w e r; Figure 7. Mounting Snowthrower
M o u n t i n g S n o w t h r o w e r Note: The auger blades are shipped in identical position for shipping purposes. Remove either left or right handshear bolt (refer to figure 18 on page 14) then turn oneauger 180” and reinstall shear bolt. 1. Park tractor on hard level surface. 2. Stop engine, lo...
Page 14 - Skid Shoe Adjustment
1 4 . A t t a c h t h e b o t t o m h a l f o f t h e s p o u t r o t a t o r h a n d c r a n k (A, figure to the spiral spring shaft (B) and secure with large ring pin at location C. 1 5 . S l i d e t h e u p p e r h a l f o f s p o u t r o t a t o r h a n d c r a n k t h r o u g h t h e r e t a i ...
Page 16 - SNOWTHROWER REMOVAL; HITCH REMOVAL
SNOWTHROWER REMOVAL R e f e r t o f i g u r e s 6 - 1 0 o n p a g e s 8 - 1 0 f o r r e m o v a l p r o c e - d u r e s . 1. Park tractor on hard level surface. 2. Lower snowthrower attachment to ground. 3. Stop engine, lock parking brake, and remove key. 4. Pull coupler (A, figure 9) on snowthrower...
Page 17 - Maintenance
MAINTENANCE STORAGEREQUIREMENTS A WARNING O n l y p e r f o r m m a i n t e n a n c e i n s p e c t i o n s a n d p r o c e -d u r e s w i t h t r a c t o r p a r k e d o n h a r d , l e v e l s u r f a c e ; PTO disengaged; engine stopped; parking brake l o c k e d a n d k e y r e m o v e d . Maint...
Page 19 - TROUBLESHOOTING
TROUBLESHOOTING A WARNING: Only perform s u r f a c e ; P T O d i s e n g a g e d , e n g i n e s t o p p e d ; p a r k i n g b r a k e l o c k e d a n d k e y r e m o v e d . PROBLEM Pivot plate will not staylocked in one position. Blower does notoperate at all. Auger does not rotate. D i s c h a r...
Page 20 - SPECIFICATIONS
DRIFT CUTTER KIT, MFG. NO. 1685189 Drift cutters can be installed on left and right hand side to assist in knocking down deep snowbanks into the auger housing. It may be necessary to drill holes for installation.Follow instructions supplied with kit. Drift Cutters SPECIFICATIONS Cutting width: 47” C...
