Simplicity 1692039 - Manual

Page 3 - Table of Contents

1 Recommended Accessories...................................................................................................................................1 Safety Rules ....................................................................................................................................

Page 4 - Safety Rules; WARNING

2 Read these safety rules and follow them closely. Failure to obey these rules could result in loss of controlof vehicle, severe personal injury to yourself or bystanders, or damage to property or equipment. The tri-angle in the text signifies important cautions or warnings which must be followed. G...

Page 5 - Components

3 Components A. Blade AssemblyB. I.D. PlateC. Hex Nut, 5/16-18 (4)D. Eyebolt (2)E. Tension Spring (2)F. Pivot Frame AssemblyG. Hex Lock Nut, 1/2-13 (2)H. Spacer (2) I. Hex Capscrew, 1/2-13 x 1 (2) J. Shoe Assembly (2)K. Plain Washer, 3/8 (4)L. Lockwasher, 3/8 (10)M. Hex Head Capscrew, 3/8-16 x 3/4 (...

Page 9 - Assembly; All Models

7 Assembly All Models 1. Place the blade on a flat surface. 2. Regent/500/2500 & Broadmoor/LT/1600/2600 Series: See Figure 4. Install one bar stop (A)using the two 5/16-18 x 1 taptite screws (B). Donot install second bar stop. Landlord/GT/1700/2700 Series: Do not install barstops. Figure 4. Bar ...

Page 12 - Installation

10 Installation Figure 10.A. Push Bar Hitch C. Hitch Pin B. Frame Bracket D. Safety Clip Broadmoor/LT/1600/2600 Series &Landlord/GT/1700/2700 Series 1. Drive the tractor over the push bar until rear of push bar is under front hitch. 2. Stop engine, remove key and set parking brake. 3. See Figure...

Page 15 - Removal; Operation On Slopes; Operation & Normal Care; Transporting

13 Removal 1. Lower the blade. 2. Remove blade and lift rod from push bar. 3. Raise push bar and unhook the spring from the chain. Remove the chain from the frame bracket.Reinstall safety clip to clevis pin. 4. Disconnect the lift rod from the lift lever on tractor by removing the spring clip. Set t...

Page 16 - Adjustments; Skid Shoe Adjustment

Lift Rod See Figure 17. For initial setting, place front set collar(A) one inch from rod guide with blade fully lowered.Place rear set collar (B) against spring (C). Tightenthe setscrews in the two set collars.To adjust, performthe following: 1. Fully raise the blade by pulling back on the tractor l...

Page 17 - Spring Tension

15 Adjustments Spring Tension See Figure 19. This snow plow/dozer blade is springloaded so that when the blade strikes a solid object,the springs will allow the blade to release as shown,rather than cause damage. The blade will go back toits original position after object is cleared. Figure 19. Doze...

Page 18 - Torque Specification Chart; Hardware Identification & Torque Specifications; Wrench & Fastener Size Guide

16 Torque Specification Chart FOR STANDARD MACHINE HARDWARE (Tolerance ± 20%) HardwareGrade SAE Grade 2 SAE Grade 5 SAE Grade 8 Size Of in/lbs in/lbs in/lbs Hardware ft/lbs Nm. ft/lbs Nm. ft/lbs Nm. 8-32 19 2.1 30 3.4 41 4.6 8-36 20 2.3 31 3.5 43 4.9 10-24 27 3.1 43 4.9 60 6.8 10-32 31 3.5 49 5.5 68...

Simplicity 1692039 - Manual

Table of Contents:

Summary

Other Simplicity Models