Shindaiwa EC7600 - Manual
Shindaiwa EC7600 – Manual, read for free online in PDF format. We hope this helps you resolve any issues you may have. If you have further questions, please contact us through the contact form.
Table of Contents:
- Page 2 – Contents; Attention Statements; Fuel Filler
- Page 3 – Before Operation; Never inhale exhaust gas.; Safety Precautions
- Page 4 – Starting The Engine
- Page 5 – Kickback; Operation
- Page 6 – Keep the unit away from children.; Stopping The Engine
- Page 7 – Safety and Operation Information Labels
- Page 8 – Unit Description
- Page 9 – Technical Specifications; Toggle switch, recoil starter
- Page 10 – Assembly; Mounting the Cut-off Wheel; Recommended Cut-off Wheels; Prior to Assembly; Carefully inspect the engine unit for
- Page 11 – Filling the Fuel Tank; Examples of 50:1 mixing quantities
- Page 12 – Keep bystanders well away.; Starting the Engine When the Engine is Cold; On
- Page 13 – Starting a Warm Engine; Keep well away from fire!; If the engine still does not start,; If the Engine Doesn’t Start; Stopping the Engine
- Page 14 – Cutting; Make sure you have a clear work
- Page 15 – Remove the blade mount from the; Reversing cutting head for flush cutting operations
- Page 16 – Inspection and Maintenance; Item; Inspection and Maintenance Requirements; Making sure that the drive belt is; Adjust the tension screw until the
- Page 17 – Cleaning the Air Cleaner
- Page 18 – Adjusting the Carburetor; Recommended idle speed:
- Page 19 – the procedures on page 13,; Cleaning Cylinder Fins; Loosen the two bolts in the belt
- Page 20 – Replacing the Drive Belt; Loosen the two bolts in the clutch; Checking the Cut-off Wheel
- Page 21 – Make sure the ignition switch is Off
- Page 22 – Checking the Fuel Filter; Take the filter out from the fuel; Lubricating the Clutch Bearing
- Page 23 – Long Term Storage
- Page 24 – Troubleshooting
- Page 25 – MANUFACTURERS WARRANTY COVERAGE
- Page 26 – PARTS COVERED; Ignition System Components; LIMITATIONS; service being performed, and; MAINTENANCE AND REPAIR REQUIREMENTS
No perform
ance guaran
tee without u
sing
genuine Shin
daiwa blade
s.
No-load revo
lution speed
: 4180 min
-1
(rpm)
Use reinforc
ed abrasive b
lades with m
aximum
useable perim
eter velocity
of 248 ft/se
c.
USE ONLY G
ENUINE
SHINDAIWA
BLADES
EC7500
Maximum b
lade diamete
r: 12 in.
Maximum b
lade thickne
ss: 0.16 in.
Arbor diam
eter: 1 inch
SHINDAIWA OWNER’S AND
OPERATOR’S MANUAL
EC7500/EC7600
ENGINE CUTOFF
SAW
WARNING!
■
Read this manual and familiarize yourself with its contents.
■
This unit is designed primarily for cutting construction materials and metal
according to the type of cutting wheel installed.
■
To minimize the risk of injury to yourself and others, always wear hearing
protection, a dustproof mask, goggles and a helmet when operating this unit.
■
Keep this manual handy so you can refer to it when required.
Part Number 68002-94310 Rev. 12/02
(EPA VERSION)
"Loading the manual" means you need to wait until the file loads and becomes available for online reading. Some manuals are very large, and the time they take to appear depends on your internet speed.
Summary
2 Throughout this manual are special“attention statements”. WARNING! A statement preceded by the word“WARNING” contains informationthat should be acted upon toprevent serious injury. CAUTION! A statement preceded by the word“CAUTION” contains informationthat should be acted upon toprevent unit damag...
3 Before Operation ■ Children and people who do notunderstand this manual mustnot use this unit. ■ Never allow other people oranimals to be near the unitwhen starting or operating. ■ Never touch a rotating cut-offwheel. ■ Operate the unit only in a wellventilated area. ■ Never operate the unit in ac...
4 Safety Precautions (continued) WARNING! Figure 1. Start the engine at least 10 feet (3 meters) from a fueling location. Starting The Engine ■ Start the engine at least 10 feet(3m) away from a fuelinglocation. ■ When starting the engine,make sure the cut-off wheeldoes not touch any object orground....
