Sharp 68-409-01 - Manual
Sharp 68-409-01 – Manual, read for free online in PDF format. We hope this helps you resolve any issues you may have. If you have further questions, please contact us through the contact form.
Table of Contents:
- Page 2 – Extron • System 8/10 P; LUS; and also turn the projector’s power OFF.; as; than XGA. Please refer to your projector user manual.; SW15 DIP Switch
- Page 3 – Sharp Installation; or
- Page 5 – Use the illustration below when connecting the System 8/10 P
- Page 6 – Sharp XG-E1200U LCD Projector Configuration
- Page 7 – buttons on the rear of the Sharp XG-E1200U, select
- Page 8 – Sharp NV6 Projector Configuration; Sharp NV6
- Page 9 – Sharp NV6 Connect.eps; CC cable
- Page 10 – Sharp NV3 Projector Configuration; Sharp NV3
- Page 11 – System 8/10 Plus - Sharp NV3 Projector Connections; Sharp PC Control adapter
Extron • System 8/10 P
LUS
• User’s Manual • P/N 68-409-01 Rev. C
Sharp Installation
Configuration and Connections
Page 1
SYSTEM 8/10 Plus
PROJECTOR COMMUNICATIONS KIT
ATTENTION!
PLEASE READ THIS DOCUMENT FOR IMPORTANT
INSTALLATION INSTRUCTIONS
THIS KIT HAS BEEN SHIPPED WITH THE FOLLOWING COMPONENTS:
Kit Type: SHARP
Included Communications Adapter(s):
Quantity
Part Number
Description
1
26-426-01
ADP, SHARP IR
1
26-467-01
ADP, UNV, “A”
THE TABLE BELOW LISTS THE POSSIBLE CONFIGURATION(S) AND CORRESPONDING
COMMUNICATIONS ADAPTER(S) FOR YOUR PROJECTOR MANUFACTURER’S VARIOUS
MODELS. PLEASE NOTE THAT YOUR SWITCHER HAS BEEN CONFIGURED AS
INDICATED BY THE “
✔
” IN THE “Config as” COLUMN. IF YOUR PROJECTOR MODEL
DIFFERS FROM THIS CONFIGURATION, YOU MUST RECONFIGURE YOUR SWITCHER
WITH THE CORRECT SETTINGS.
PLEASE REFER TO THE FOLLOWING PAGES FOR COMPLETE CONFIGURATION AND
SIGNAL CONNECTION INSTRUCTIONS.
THIS SWITCHER HAS BEEN CONFIGURED FOR:
SHARP XG (RS-232)
Config
Model
Rotary Switches Cable
SW15 Settings
Comm
as
RS1 RS2 RS3 RS4 J2/J3 1 2 3 4 5 6 7 8 9 10 Adapter
✔
XG (RS-232)
0
0
F
9
J2
↓ ↓ ↑ ↓ ↑ ↓ ↓ ↓ ↑ ↓
26-467-01
XG-E1200U
1
0
F
3
J2
↑ ↓ ↑ ↓ ↑ ↓ ↓ ↓ ↑ ↓
26-426-01
XG-1000/E1100
0
0
F
3
J2
↑ ↓ ↑ ↓ ↑ ↓ ↓ ↓ ↑ ↓
26-426-01
XG-NV6/NV2U/NV5
2
0
F
9
J2
↑ ↓ ↑ ↓ ↑ ↓ ↓ ↓ ↑ ↓
26-467-01
XG-NV3
1
0
F
9
J2
↑ ↓ ↑ ↓ ↑ ↓ ↓ ↓ ↑ ↓
26-467-01
XG-P10XU
2
0
F
9
J2
↑ ↓ ↑ ↓ ↑ ↓ ↓ ↓ ↑ ↓
26-467-01
PG-C30XU
2
0
F
9
J2
↑ ↓ ↑ ↓ ↑ ↓ ↓ ↓ ↑ ↓
26-467-01
XG-P20XU
1
0
F
9
J2
↑ ↓ ↑ ↓ ↑ ↓ ↓ ↓ ↑ ↓
26-467-01
"Loading the manual" means you need to wait until the file loads and becomes available for online reading. Some manuals are very large, and the time they take to appear depends on your internet speed.
Summary
Extron • System 8/10 P LUS • User’s Manual • P/N 68-409-01 Rev. C Sharp Installation Configuration and Connections Page 2 Sharp XG Series Projector Configuration (RS-232) Verify that the System 8/10 Plus is already configured for the Sharp XG Seriesprojector by following the procedure and switch set...
Extron • System 8/10 P LUS • User’s Manual • P/N 68-409-01 Rev. C Sharp Installation Configuration and Connections Page 3 System 8/10 Plus to Sharp XG Series Projector Connections (RS-232) Use the illustration below as a guide when connecting the System 8/10 Plus to aSharp projector. Refer to Sharp ...
Extron • System 8/10 P LUS • User’s Manual • P/N 68-409-01 Rev. C Sharp Installation Configuration and Connections Page 5 Sharp XG-1000/E1100 Projector Connections Use the illustration below when connecting the System 8/10 P LUS to a Sharp XG- 1000/E1100 projector. Refer to Sharp documentation to co...
