Sennheiser Set 820 S - Manual

28 SET 820 S English Only use one of the two audio inputs on the transmitter (MIC or LINE). Connect the power cable to the POWER socket on the transmitter. Plug the power supply into a household electrical outlet. Pull the power supply unit out of the electrical outlet when the unit will notbe used ...

SET 820 S 29 English Where to place the transmitter Choose a suitable place near or on top of your hi-fi system or TV set. Do not place the transmitter close to metal objects such as shelf bars, reinforced concrete walls, etc. The transmitter features a convenient automatic on/off function. The tran...

30 SET 820 S English Using the receiver The receiver is turned on automatically as soon as a 3.5 mm stereo jack plug is insert-ed into the socket at the top of the receiver. Affix the receiver to the clothing by means of its integrated attachment clip. Using the induction neck loop Put the EZT 1011 ...

SET 820 S 31 English Adjusting the volume Adjust the receiver’s volume with the operating control. If you are not using the receiver, pull the 3.5 mm stereo jack plug out of the receiver’s socket to avoid di-scharging the battery. The receiver is then turned off. Set 820 S_511981_0106_Sp7.book Seite...

32 SET 820 S English Changing the transmission channel To avoid interference caused by the simultaneous operation of se-veral transmitters, select a diffe-rent channel on each transmitter.To select a channel, set the CHANNEL switch at the rear of the transmitter to the desired po-sition. Due to rest...

34 SET 820 S English Adjusting the receiver channel First turn on the transmitter (see section “Where to place the transmitter”). As soon as the receiver is turned on, it au-tomatically tunes itself to the first strong si-gnal found (normally the transmitter frequency). If, for some reason, the sele...

SET 820 S 35 English Charging the battery Place the receiver into the transmitter’s charging compartment, with the operating control at the front. Pull the 3.5 mm stereo plug out of the receiver to turn the receiver off. The left LED on the transmitter must li-ght up. Charge the battery for 24 hours...

36 SET 820 S English A battery has a service life of 1-2 years and should be replaced if the ope-rating time decreases. Sennheiser batteries can be recycled. Please dispose of the batteries as special waste or return them to your specialist dealer. To protect the envi-ronment, only dispose of totall...

SET 820 S 37 English WARNING: Volume up? - No! When people use headphones, they tend to choose a higher volume than with loudspeakers. However, if your hearing has deteriorated and you need to rely on an assitive listening system, please avoid listening at high volume levels for a long time. Please ...

SET 820 S 39 English BA 151 rechargeable battery By using a spare battery, you can use the receiver for more than four hours of continuous operation. Always store the spare battery in the small charging compartment at the right of the transmitter. The right LED on the transmitter lights up green to ...

40 SET 820 S English MKE 800 TV external microphone If your TV doesn’t have a headphone output, SCART or RCA socket, youcan use your Set 820 S together with the MKE 800 TV microphone. Fix the microphone to the loudspeaker of your TV by means of Velcro tape. Connect the microphone connector to the MI...

SET 820 S 41 English - Are the receiver and sound source turned on and is the volume of the receiver and sound source sufficient? - Is the rechargeable battery inserted properly into the receiver?- Have you charged the rechargeable battery for at least 20 minutes?- Are you too far from the transmitt...

42 SET 820 S English Additional information for hearing aid acousticians Adjustments for hearing disabilities Attention: In order to ensure interference-free reception, only use the potentiometers shown below. Turn the operating control fully to the left (0). Remove the operating control by carefull...

SET 820 S 43 English The adjustments can also be made when the receiver is being used. When replacing the operating control, make sure the "projections" on the inside of the operating control point in the direction of the attachment clip. After replacing the operating control, synchronize th...

SET 820 S 45 English Manufacturer declarations CE Declaration of Conformity This equipment is in compliance with the essential requirements and other relevant provisions of Directi-ves 1999/5/EC, 89/336/EC or 73/23/EC. The declaration is available on the internet site at www.sennhei-ser.com.Before p...