SEAGATE ST31000533CS - Manual

Pipeline HD Pro Serial ATA Product Manual, Rev. C 1 1.0 Introduction This manual describes the functional, mechanical and interface specifications for the following Seagate Pipeline HD ® Pro Serial ATA model drives: These drives provide the following key features:• 7,200 RPM spindle speed.• High ins...

2 Pipeline HD Pro Serial ATA Product Manual, Rev. C 1.1 About the Serial ATA interface The Serial ATA interface provides several advantages over the traditional (parallel) ATA interface. The primary advantages include:• Easy installation and configuration with true plug-and-play connectivity. It is ...

Pipeline HD Pro Serial ATA Product Manual, Rev. C 3 2.0 Drive specifications Unless otherwise noted, all specifications are measured under ambient conditions, at 25°C, and nominal power. For convenience, the phrases the drive and this drive are used throughout this manual to indicate the following d...

4 Pipeline HD Pro Serial ATA Product Manual, Rev. C Table 1: Drive specifications summary for 1000 Gbyte models Drive specification ST31000533CS Formatted capacity (512 bytes/sector)* 1000 Gbytes Guaranteed sectors 1,953,525,168 Heads 6 Discs 3 Bytes per sector 512 Default sectors per track 63 Defau...

6 Pipeline HD Pro Serial ATA Product Manual, Rev. C 2.1 Formatted capacity *One Gbyte equals one billion bytes when referring to hard drive capacity. Accessible capacity may vary depending on operating environment and formatting. 2.1.1 LBA mode When addressing these drives in LBA mode, all blocks (s...

Pipeline HD Pro Serial ATA Product Manual, Rev. C 7 2.4 Physical characteristics 2.5 Seek time Seek measurements are taken with nominal power at 25°C ambient temperature. All times are measured using drive diagnostics. The specifications in the table below are defined as follows:• Track-to-track see...

8 Pipeline HD Pro Serial ATA Product Manual, Rev. C 2.7 Power specifications The drive receives DC power (+5V or +12V) through a native SATA power connector. See Figure 2 on page 18. 2.7.1 Power consumption Power requirements for the drives are listed in the table on page 9. Typical power measuremen...

10 Pipeline HD Pro Serial ATA Product Manual, Rev. C 2.8 Environmental specifications 2.8.1 Ambient temperature Ambient temperature is defined as the temperature of the environment immediately surrounding the drive. Actual drive case temperature should not exceed 69°C (156°F) within the operating am...

Pipeline HD Pro Serial ATA Product Manual, Rev. C 11 2.8.5.2 Nonoperating shock 1000 GB models The nonoperating shock level that the drive can experience without incurring physical damage or degradation in performance when subsequently put into operation is 300 Gs based on a nonrepetitive half-sine ...

12 Pipeline HD Pro Serial ATA Product Manual, Rev. C 2.9 Acoustics Drive acoustics are measured as overall A-weighted acoustic sound power levels (no pure tones). All mea-surements are consistent with ISO document 7779. Sound power measurements are taken under essentially free-field conditions over ...

Pipeline HD Pro Serial ATA Product Manual, Rev. C 13 2.11 Reliability 2.11.1 Annualized Failure Rate (AFR) and Mean Time Between Failures (MTBF) The product shall achieve an Annualized Failure Rate (AFR) of 0.62% when operated in an environment of ambient air temperatures of 25 ° C. Operation at tem...

14 Pipeline HD Pro Serial ATA Product Manual, Rev. C Korean RRL If these drives have the Korea Ministry of Information and Communication (MIC) logo, they comply with paragraph 1 of Article 11 of the Electromagnetic Compatibility control Regulation and meet the Electromagnetic Compatibility (EMC) Fra...

Pipeline HD Pro Serial ATA Product Manual, Rev. C 15 2.13 Environmental protection Seagate designs its products to meet environmental protection requirements worldwide, including regulations restricting certain chemical substances. 2.13.1 European Union Restriction of Hazardous Substances (RoHS) Dir...

Pipeline HD Pro Serial ATA Product Manual, Rev. C 17 3.0 Configuring and mounting the drive This section contains the specifications and instructions for configuring and mounting the drive. 3.1 Handling and static-discharge precautions After unpacking, and before installation, the drive may be expos...

18 Pipeline HD Pro Serial ATA Product Manual, Rev. C 3.2 Configuring the drive Each drive on the Serial ATA interface connects point-to-point with the Serial ATA host adapter. There is no master/slave relationship because each drive is considered a master in a point-to-point relationship. If two dri...

Pipeline HD Pro Serial ATA Product Manual, Rev. C 19 3.4 Drive mounting You can mount the drive in any orientation using four screws in the side-mounting holes or four screws in the bottom-mounting holes. See Figure 3 for drive mounting dimensions. Follow these important mounting precau-tions when m...

Pipeline HD Pro Serial ATA Product Manual, Rev. C 21 4.0 Serial ATA (SATA) interface These drives use the industry-standard Serial ATA interface that supports FIS data transfers. It supports ATA programmed input/output (PIO) modes 0–4; multiword DMA modes 0–2, and Ultra DMA modes 0–6. For detailed i...

22 Pipeline HD Pro Serial ATA Product Manual, Rev. C 4.2 Serial ATA device plug connector pin definitions Table 5 summarizes the signals on the Serial ATA interface and power connectors. . Notes: 1. All pins are in a single row, with a 1.27 mm (0.050”) pitch. 2. The comments on the mating sequence a...

Pipeline HD Pro Serial ATA Product Manual, Rev. C 23 4.3 Supported ATA commands The following table lists Serial ATA standard commands that the drive supports. For a detailed description of the ATA commands, refer to the Serial ATA International Organization: Serial ATA Revision 2.6 (http://www.sata...

Pipeline HD Pro Serial ATA Product Manual, Rev. C 25 4.3.1 Identify Device command The Identify Device command (command code EC H ) transfers information about the drive to the host following power up. The data is organized as a single 512-byte block of data, whose contents are shown in Table 6 on p...

26 Pipeline HD Pro Serial ATA Product Manual, Rev. C 60–61 Total number of user-addressable LBA sectors available(see Section 2.1 for related information)*Note: The maximum value allowed in this field is: 0FFFFFFFh (268,435,455 sectors, 137 Gbytes). Drives with capacities over 137 Gbytes will have 0...

Pipeline HD Pro Serial ATA Product Manual, Rev. C 27 Note. Advanced Power Management (APM) and Automatic Acoustic Management (AAM) features are not supported Note. See the bit descriptions below for words 63, 84, and 88 of the Identify Drive data. 108–111 The mandatory value of the world wide name (...

Pipeline HD Pro Serial ATA Product Manual, Rev. C 29 4.3.2 Set Features command This command controls the implementation of various features that the drive supports. When the drive receives this command, it sets BSY, checks the contents of the Features register, clears BSY and generates an inter-rup...

Pipeline HD Pro Serial ATA Product Manual, Rev. C 31 5.0 Seagate Technology support services Online services Internet For information regarding Seagate products and services, visit www.seagate.com . Worldwide support is available 24 hours daily by email for your questions. Presales Support: Presales...

32 Pipeline HD Pro Serial ATA Product Manual, Rev. C Customer Service Operations Warranty Service Seagate offers worldwide customer support for Seagate products. Seagate distributors, OEMs and other direct customers should contact their Seagate Customer Service Operations (CSO) representative for wa...

Pipeline HD Pro Serial ATA Product Manual, Rev. C 33 Index A ACA 14 acceleration 11 acoustics 12 Active 9 Active mode 9 AFR 13 Agency certification 13 altitude 10 Ambient temperature 10 ambient temperature 7 , 8 Annualized Failure Rate 13 Annualized Failure Rate (AFR) 13 areal density 1 , 6 ATA comm...

Seagate Technology LLC 920 Disc Drive, Scotts Valley, California 95066-4544, USA Publication Number: 100527225, Rev. C, Printed in U.S.A.