Page 2 - INTRODUCTION; The Engine Exhaust from this
Introduction INTRODUCTION THANK YOU for purchasing a Scotts product. Read this manual and your attachment manual thoroughly. Failure to do so could result in personal injury or equipment damage. This manual should be considered a permanent part of your machine and should remain with the machine when...
Page 3 - TABLE OF CONTENTS
Table of Contents TABLE OF CONTENTS OMM138757 L8 All information, illustrations and specifications in this manual are based on the latest information at the time of publication. The right is reserved to make changes at any time without notice. COPYRIGHT© 1998 Deere & Co. Assembly ..................
Page 4 - NOTES
Notes NOTES Downloaded from www.Manualslib.com manuals search engine
Page 7 - ASSEMBLY; Identify Parts; Check Battery
Assembly - Page 1 ASSEMBLY Identify Parts Clear Plastic Bag Contains:• Scotts Operator’s Manual• Engine Owner’s Manual• Safety Video• Warranty Cards Bag of Parts Contains:• Hardware for Steering Wheel• Hardware for Battery Cables• Key Chain• Padded Key NOTE: There is an extra ignition key strapped t...
Page 8 - Connect Battery; Install Steering Wheel; Put front wheels in the straight forward position.
Assembly - Page 2 ASSEMBLY Connect Battery NOTE: Do not remove the BLACK negative (–) protective cap at this time. 1. Remove and discard the RED positive (+) protective cap from the positive (+) battery terminal. 2. Connect blue harness wire (A) and RED positive (+) cable (B) to battery. Apply petro...
Page 9 - Check Engine Oil; Oil must be between ADD and FULL marks.; Break-In Electric PTO Clutch
Assembly - Page 3 ASSEMBLY Check Engine Oil 1. Lift hood. Picture Note: Model S2048 used for photo purposes. 2. Remove dipstick (A). Wipe with clean cloth. 3. Insert the dipstick into the tube and rest the oil fill cap on the tube. Do not thread the cap onto the tube. 4. Remove dipstick to check oil...
Page 10 - Check Machine Safety System; Check tire pressure with an accurate gauge.; Tire Size
Assembly - Page 4 ASSEMBLY Check Machine Safety System Perform safety system check to make sure the electronic safety interlock circuit is functioning properly. Perform all six Tests. (See Testing Safety System in the Operating section.) Checking Tire Pressure 1. Check tires for damage. 2. Check tir...
Page 11 - SAFETY SIGNS; Machine Safety Labels; DANGER
Safety Signs - Page 5 SAFETY SIGNS Safety-Alert Symbol Read and recognize safety information. Be alert to the potential for personal injury when you see this safety-alert symbol. On your machine safety labels, the words DANGER, WARNING, and CAUTION are used with this safety-alert symbol. DANGER iden...
Page 12 - WARNING; • SPARKS; FLUSH EYES IMMEDIATELY WITH WATER.
Safety Signs - Page 6 SAFETY SIGNS WARNING LOADED SPRING LOCK LIFT LEVER FORWARD BEFORE CHANGING ATTACHMENTS Picture Note: One decal on each side of tractor frame. DANGER/POISON SHIELD EYES. EXPLOSIVE GASES CAN CAUSE BLINDNESS OR INJURY. NO • SPARKS • FLAMES • SMOKING SULFURIC ACID CAN CAUSE BLINDNE...
Page 13 - Certification Label
Safety Signs - Page 7 SAFETY SIGNS DANGER ROTATING BLADE DO NOT PUT HANDS OR FEET UNDER OR INTO MOWER WHEN ENGINE IS RUNNING THROWN OBJECTS BEFORE MOWING, CLEAR AREA OF OBJECTS THAT MAY BE THROWN BY BLADE DO NOT OPERATE MOWER WITHOUT DISCHARGE CHUTE OR ENTIRE GRASS CATCHER IN PLACE DANGER ROTATING B...
Page 14 - CONTROLS; Controls
Controls - Page 8 CONTROLS Controls Picture Note: Model S2554 used for photo purposes. A - Engine Oil Pressure Light (Model S2554 Only) B - Hour Meter (Model S2554 Only) C - Battery Discharge Light D - Light Switch E - PTO Switch/RIO Switch F - Choke Knob G - Throttle Lever H - Key Switch I - Park B...
Page 15 - OPERATING MACHINE; Operate Safely; • Stop machine on a level surface, not on a slope.
Operating Machine - Page 9 OPERATING MACHINE Operate Safely • In addition to reading your Operator’s Manual, view your Mowing Safety Video. • Check brake action before you operate. Adjust or service brakes as necessary. • Inspect machine before you operate. Be sure hardware is tight. Repair or repla...
Page 16 - • Turn machine off if a child enters the mowing area.
Operating Machine - Page 10 OPERATING MACHINE Rotating Blades are Dangerous - Protect Children and Prevent Accidents PROTECT CHILDREN: • Never assume that children will remain where you last saw them. Children are attracted to mowing activity, stay alert to the presence of children. • Keep children ...
Page 17 - Avoid Tipping; • DO NOT drive where machine could slip or tip.; Keep Riders Off
Operating Machine - Page 11 OPERATING MACHINE Avoid Tipping • DO NOT drive where machine could slip or tip. • Stay alert for holes and other hidden hazards in the terrain. • Keep away from drop-offs. • Slow down before you make a sharp turn or operate on a slope. • When pulling loads or using heavy ...
Page 18 - Wear Appropriate Clothing; Tighten knobs after adjustment to keep seat in place.
Operating Machine - Page 12 OPERATING MACHINE Wear Appropriate Clothing • Wear close fitting clothing and safety equipment appropriate for the job. • Loud noise can cause impairment or loss of hearing, wear a suitable protective device such as earplugs. Transport Safely • Use safety lights and devic...
Page 19 - Using the Park Brake; UNLOCKING PARK BRAKE:; Using Headlights; Push bottom of light switch to turn headlights OFF.
Operating Machine - Page 13 OPERATING MACHINE Using the Park Brake LOCKING PARK BRAKE: 1. Push brake pedal (A) all the way down. 2. Lift park brake lever (B) up. 3. Release pedal and park brake lever. Pedal should stay down and park brake lever should stay LOCKED in UP position. UNLOCKING PARK BRAKE...
Page 20 - Checking Indicator Lights and Hour Meter; ) position. The voltage light may remain on for; Starting Engine; Lock the park brake or depress brake pedal.
Operating Machine - Page 14 OPERATING MACHINE Checking Indicator Lights and Hour Meter Picture Note: Model S2554 used for photo purposes. • ( b ) BATTERY DISCHARGE light (A) should go out when throttle lever is moved to the HIGH IDLE/Mowing ( a ) position. The voltage light may remain on for several...
Page 21 - Warming and Idling Engine; • Run Engine at half speed for 2–3 minutes.; Stopping Engine; ) positions. Let the engine run a minimum of
Operating Machine - Page 15 OPERATING MACHINE 7. Check starting conditions: • If engine is COLD: Gradually return the choke to the OFF position after the engine starts and warms up. • If engine is WARM: Return choke to the OFF position as soon as the engine starts. 8. Let engine run for a couple of ...
Page 22 - Using and Stopping Automatic Transmission; To Travel in Reverse:
Operating Machine - Page 16 OPERATING MACHINE Using and Stopping Automatic Transmission UNLOCK park brake. To Travel Forward: 6. • Slowly push down forward pedal (A). Tractor will travel faster the farther down you push the pedal. • Release forward pedal, tractor will automatically return to neutral...
Page 23 - Pushing Machine; To move machine when engine is STOPPED:
Operating Machine - Page 17 OPERATING MACHINE Pushing Machine To move machine when engine is STOPPED: • Unlock the park brake (A). • Pull out on free-wheeling lever (B). • Push machine to desired location. NOTE: Push free-wheeling lever (B) in before operating tractor. IMPORTANT: Avoid transmission ...
Page 24 - Using Reverse Implement Option; • Test safety systems.
Operating Machine - Page 18 OPERATING MACHINE Using Reverse Implement Option NOTE: Operating the mower while backing up is strongly discouraged. The Reverse Implement Option should be used ONLY when operating another attachment or when the operator deems it necessary to reposition the machine with t...
Page 25 - Testing Safety Systems; Check operation of indicator lights:
Operating Machine - Page 19 OPERATING MACHINE Testing Safety Systems NOTE: Your Tractor is equipped with a ELECTRONIC SAFETY INTERLOCK. Engine will not start unless: PTO switch is DISENGAGED; Brake pedal is depressed OR parking brake is set. Use the following checkout procedure to check for normal o...
Page 28 - Test Reverse Implement Option:
Operating Machine - Page 22 OPERATING MACHINE Test 8 Test Reverse Implement Option: 1. Start engine. 2. Engage PTO to start attachment. 3. Look behind the vehicle to be sure there are no bystanders. 4. Begin REVERSE travel by depressing REVERSE foot pedal. 5. Attachment and engine should stop operat...
Page 29 - Using Front Weights; Remove front wheel weights when not required.; Using Rear Wheel Weights
Operating Machine - Page 23 OPERATING MACHINE Avoid Using Ground Engaging Equipment (Model S2048 Only) Tractor Model S2048 is not intended for use with ground engaging equipment such as a rear tiller, disk, dirt blade or plow. Using Front Weights NOTE: Before installing wheel weights on your machine...
Page 30 - Installing the Chains
Operating Machine - Page 24 OPERATING MACHINE Installing the Chains NOTE: Tire chains are recommended for use with snowthrower and, under certain conditions, the front blade. 1. Park vehicle safely. 2. Remove chains from bag and lay out flat with the cross chain hook ends facing upward. Remove any t...
Page 31 - Transporting; Use a heavy-duty trailer to transport your machine.; Maintain proper air pressure in tires.
Operating Machine - Page 25 OPERATING MACHINE 8. Tie excess rim chain links (G) back to the rim chain. 9. The chain should be as tight as possible by hand. Unhook the fastener and repeat Step 5 if the chain is loose. 10.Drive forward on chains 30’-40’ and recheck for tightness. Adjust as necessary. ...
Page 32 - OPERATING MOWER; Operating Mower Safely; Before you dismount to unplug or adjust mower:
Operating Mower - Page 26 OPERATING MOWER Operating Mower Safely • In addition to reading your Operator’s Manual, view your Mowing Safety Video. Check Ground Conditions • Clear mowing area of objects that might be thrown. Keep people and pets out of mowing area. • Study mowing area. Set up safe mowi...
Page 33 - Using Lift Lever to Raise and Lower Mower; • Push lever forward until it latches down.; Adjusting Cutting Height
Operating Mower - Page 27 OPERATING MOWER Using Lift Lever to Raise and Lower Mower Check out the two different lift lever positions before operation: • TRANSPORT (UPPER) POSITION: Raises mower for transport. • MOWING (LOWER) POSITION: Maintains cutting height set by mower height control yet allows ...
Page 34 - Adjusting Mower Gage Wheels; Check distance from gage wheel to ground.
Operating Mower - Page 28 OPERATING MOWER Adjusting Mower Gage Wheels 1. Check tractor tire pressure. Inflate tires to the correct pressure. (See Checking Tire Pressure in Service - Miscellaneous section.) 2. Raise mower lift lever to TRANSPORT (upper) position and adjust cutting height. (See Adjust...
Page 36 - Turn left blade so blade tip points straight forward.
Operating Mower - Page 30 OPERATING MOWER Adjusting Mower Level (Front-to-Rear) NOTE: Mower gage wheels should not contact the ground during leveling. 1. Park tractor on a hard, level surface. 2. Stop engine and remove key. 3. CHECK: Tire pressure must be correct. (See Checking Tire Pressure in Serv...
Page 37 - Engaging Mower; Disengage PTO before shifting to REVERSE.; Disengaging Mower; Push PTO switch down to DISENGAGE mower.; ) when mowing or after mower blades
Operating Mower - Page 31 OPERATING MOWER Engaging Mower 1. START engine. Picture Note: Model S2554 shown for photo purposes. 2. Move throttle lever (A) to the FAST ( r ) position. 3. Lower mower to cutting height. 4. Pull PTO switch (B) up to ENGAGE mower. NOTE: Any operating attachment and the eng...
Page 38 - REPLACEMENT PARTS; Parts for Tractor and Mower Deck; ITEM
Replacement Parts - Page 32 REPLACEMENT PARTS WE RECOMMEND quality parts and lubricants, available at your Authorized Service Center. PART NUMBERS MAY CHANGE, use part numbers listed below when you order. If a number changes, your dealer will have the latest number. WHEN YOU ORDER PARTS, your Author...
Page 39 - SERVICE MACHINE SAFELY; Practice Safe Maintenance; Before you unplug or adjust machine:
Service Machine Safely - Page 33 SERVICE MACHINE SAFELY Practice Safe Maintenance • Understand service procedure before doing work. Keep area clean and dry. • Never lubricate, service, or adjust machine while it is moving. Keep safety devices in place and in working condition. Keep hardware tight. •...
Page 40 - Handling Waste Product and Chemicals
Service Machine Safely - Page 34 SERVICE MACHINE SAFELY Handling Waste Product and Chemicals • Waste products such as used oil, fuel, coolant, brake fluid, and batteries, can harm the environment and people. • DO NOT use beverage containers for waste fluids - someone may drink from them. • See your ...
Page 41 - SERVICE INTERVAL CHART; Service Intervals
Service Interval Chart - Page 35 SERVICE INTERVAL CHART Service Intervals Please use the following timetables to perform routine maintenance on your machine. Service procedures included in this manual but not on this chart are to be performed on an as needed basis. IMPORTANT: To extend engine life, ...
Page 42 - Service Record; Before Storage
Service Interval Chart - Page 36 SERVICE INTERVAL CHART Service Record Before Storage Check/tighten loose hardware.Lubricate front axle and mower spindles.Clean battery terminals.Change engine oil.Inspect muffler.Check transaxle cooling. DATE SERVICE PERFORMED Downloaded from www.Manualslib.com manu...
Page 43 - SERVICE ENGINE; Engine Warranty Maintenance Statement
Service Engine - Page 37 SERVICE ENGINE Engine Warranty Maintenance Statement Maintenance, repair, or replacement of the emission control devices and systems on this engine, which are being done at the customers expense, may be performed by any nonroad engine repair establishment or individual. Warr...
Page 44 - Avoid Fumes; Use a high quality detergent oil classified as:
Service Engine - Page 38 SERVICE ENGINE Avoid Fumes Engine Oil NOTE: Air cooled engines run hotter than automobile engines. The use of multi-viscosity oil such as (10W-30) in ambient temperatures above 4 ° C (40° F) will result in higher than normal oil consumption. If multi-viscosity oil is used, c...
Page 45 - Checking Engine Oil Level; Remove dipstick and check the oil level.; Changing Engine Oil; Wipe debris and dirt from around dipstick.
Service Engine - Page 39 SERVICE ENGINE Checking Engine Oil Level 1. Park tractor on a level surface. STOP engine. Let engine cool. 2. Lift hood. 3. Clean area around dipstick to prevent debris from falling into crankcase. Picture Note: Model S2048 used for photo purposes. 4. Remove dipstick (A). Wi...
Page 46 - Changing Engine Oil Filter; Wipe debris and dirt from around oil filter.
Service Engine - Page 40 SERVICE ENGINE 8. Install dipstick and then remove to check oil level. (See Checking Engine Oil in this section.) Oil level must be between ADD and FULL marks. Do not overfill. 9. Install and tighten dipstick. 10.Start engine and check for oil leaks. Correct any leaks before...
Page 47 - Cleaning Air Intake Screen and Engine Fins; Keep cooling fins free of dust.
Service Engine - Page 41 SERVICE ENGINE Cleaning Air Intake Screen and Engine Fins 1. STOP engine. LOCK park brake and remove key. 2. Lift hood. Picture Note: Model S2554 shown for photo purposes. 3. Clean air intake screen (A), oil cooler fins (B) on Model S2554, and external surfaces, with rag, br...
Page 49 - Checking Spark Plugs; Clean spark plugs carefully with a wire brush.; Replacing Fuel Filter; NOTE: Change filter when fuel is low in fuel tank.
Service Engine - Page 43 SERVICE ENGINE Checking Spark Plugs 1. Stop engine. Remove key. Lift hood. 2. Disconnect spark plug wires (A), one on each side, and remove spark plugs. Picture Note: Model S2048 used for photo purposes. 3. Clean spark plugs carefully with a wire brush. 4. Check plug gap wit...
Page 50 - SERVICE TRANSMISSION; Transmission Oil; NOTE: Your tractor is filled with 5W30 at the factory; When adding transmission fluid:; Check Transmission Fluid Level; Allow oil in transmission to cool before checking.; Adding Transmission Fluid
Service Transmission - Page 44 SERVICE TRANSMISSION Transmission Oil NOTE: Your tractor is filled with 5W30 at the factory When adding transmission fluid: • S2048 use 5W30 or 10W30. • S2554 use 5W50 Synthetic. Check Transmission Fluid Level 1. Park machine on level surface. 2. Allow oil in transmiss...
Page 51 - SERVICE MOWER; Avoid Injury From Contacting Blades; The following greases may be used:; Lubricating Mower Spindles; Disconnect spark plug wire from spark plug.
Service Mower - Page 45 SERVICE MOWER Avoid Injury From Contacting Blades Grease Use grease based on the expected air temperature range during the service interval. The following greases may be used: • SAE Multipurpose EP Grease with 3 to 5 percent molybdenum disulfide. • SAE Multipurpose EP Grease....
Page 52 - Replacing Mower Drive Belt
Service Mower - Page 46 SERVICE MOWER Replacing Mower Drive Belt 1. Park vehicle safely. 2. Remove mower deck. (See Removing Mower in Removing Mower section.) 3. Remove three cap screws and belt shields (A). 4. Put drive belt tension rod (B) in the released position as shown and disconnect idler spr...
Page 53 - Servicing Mower Blades; REMOVING MOWER BLADES
Service Mower - Page 47 SERVICE MOWER Servicing Mower Blades REMOVING MOWER BLADES 1. Raise mower deck to gain access to mower blades. If necessary, remove mower deck. 2. Use a wooden block to prevent mower blades from spinning. 3. Remove cap screw (A), round blade washer (B), blade (C) and deflecto...
Page 54 - Sharpening Blades
Service Mower - Page 48 SERVICE MOWER Sharpening Blades 1. Sharpen blades with grinder, hand file or electric blade sharpener. 2. Keep original bevel (A) when you grind. 3. Blade should have 0.40 mm (1/64 in.) cutting edge (B). Balancing Blades 1. Clean blade. 2. Put blade on nail in vise or on vert...
Page 55 - SERVICE ELECTRICAL; Checking the Battery; • Keep battery and terminals clean.; Removing and Installing the Battery
Service Electrical - Page 49 SERVICE ELECTRICAL Checking the Battery NOTE: This is a maintenance free battery, do not attempt to open or service battery in any way. • Keep battery and terminals clean. • Keep battery bolts tight. • Keep small vent holes open. • Recharge, if necessary, at 6–10 amperes...
Page 56 - Clean Battery and Terminals; blue
Service Electrical - Page 50 SERVICE ELECTRICAL Clean Battery and Terminals 1. Turn ignition key off and lift hood. 2. Remove rubber hold-down strap (A). 3. Disconnect BLACK (–) battery cable (B) first. 4. Disconnect RED (+) battery cable (C) and blue harness wire (D) and remove battery from mower. ...
Page 57 - Charging the Battery
Service Electrical - Page 51 SERVICE ELECTRICAL Charging the Battery Before you charge a battery: • Wait until the battery has warmed to room temperature. Do not charge a frozen battery. Turn OFF and unplug the charger before you con-nect cables to the battery or disconnect cables fromthe battery. I...
Page 58 - Using Booster Battery; Battery gas is explosive:
Service Electrical - Page 52 SERVICE ELECTRICAL 1. Remove battery from mower. (See Removing and Installing Battery in this section.) 2. Connect positive (+) charger cable to positive (+) battery terminal. 3. Connect negative (–) charger cable to negative (–) battery terminal. 4. Plug in charger cord...
Page 59 - Replacing Fuse
Service Electrical - Page 53 SERVICE ELECTRICAL Replacing Fuse 1. Lift hood. 2. Pull defective fuse (A) out of socket. 3. Check metal clip in fuse window and discard fuse if clip is broken. 4. Push new fuse into socket. 5. Lower hood. Replacing Headlight Bulb 1. Lift hood. 2. Push in and turn bulb s...
Page 60 - SERVICE MISCELLANEOUS; Checking Tire Pressure
Service Miscellaneous - Page 54 SERVICE MISCELLANEOUS Checking Tire Pressure 1. Check tires for damage. 2. Check tire pressure with an accurate gauge. 3. Add or remove air, if necessary: c CAUTION: Explosive separation of a tire and rim parts can cause serious injury or death: - Do not attempt to mo...
Page 61 - Fuel; Using Clean Fuels
Service Miscellaneous - Page 55 SERVICE MISCELLANEOUS Fuel Using Clean Fuels Dirt in the fuel system is a major cause of performance problems. Be sure to clean any grass or trash from the top of the tank before removing lid. Use of a PLASTIC funnel with a plastic mesh strainer when filling the tank ...
Page 62 - Octane Rating
Service Miscellaneous - Page 56 SERVICE MISCELLANEOUS Octane Rating Regular grade 87 octane unleaded fuel is recommended for use in your tractor. Higher octane fuels will seldom make your tractor perform better. If your tractor develops a starting or performance problem immediately after use of new ...
Page 63 - Using Fresh Fuel and Stabilizers; Filling Fuel Tank; Fill tank with fresh fuel only to bottom of filler neck.
Service Miscellaneous - Page 57 SERVICE MISCELLANEOUS Using Fresh Fuel and Stabilizers The best thing you can do to ensure peak performance of your engine is to use “fresh” fuel. Your tractor’s engine will perform well with most good-quality fresh fuels regardless of additives. Any fuel will begin t...
Page 64 - Grease
Service Miscellaneous - Page 58 SERVICE MISCELLANEOUS Grease Use grease based on the expected air temperature range during the service interval. The following greases may be used: • SAE Multipurpose EP Grease with 3 to 5 percent molybdenum disulfide. • SAE Multipurpose EP Grease. • Greases meeting M...
Page 65 - Care for Plastic and Painted Surfaces; PLASTIC SURFACES
Service Miscellaneous - Page 59 SERVICE MISCELLANEOUS Care for Plastic and Painted Surfaces PLASTIC SURFACES The plastic parts on your tractor are made of a blend of polycarbonate and polyester materials. These parts are extremely strong and durable. Unlike painted metal, the plastic parts will neve...
Page 66 - • DO NOT use solvents or commercial cleaners.
Service Miscellaneous - Page 60 SERVICE MISCELLANEOUS Avoid Damage: • “Dry wiping” or wiping the plastic surface when it is dry is a major source of minor surface scratches. • DO NOT wipe hood or other plastic parts unless wetted first. • DO NOT apply wax unless plastic surface has been thoroughly c...
Page 67 - PAINTED METAL SURFACES
Service Miscellaneous - Page 61 SERVICE MISCELLANEOUS PAINTED METAL SURFACES Correct Cleaning Care: Follow automotive practices to care for your tractor painted metal surfaces. Use a high-quality automotive wax regularly to maintain the factory look of your tractor’s painted surfaces. Repair: Minor ...
Page 68 - REMOVING MOWER; Removing Mower; Put wood blocks under each side of mower.
Removing Mower - Page 62 REMOVING MOWER Removing Mower 1. STOP engine, LOCK park brake, push PTO switch down to DISENGAGE, turn key to the OFF position, and remove key. 2. Raise mower lift lever to TRANSPORT (upper) position. 3. Set cutting height knob (A) to 25 mm (1 in.). 4. Put wood blocks under ...
Page 69 - Slide mower out from under the tractor.
Removing Mower - Page 63 REMOVING MOWER 9. Disconnect draft arms, one on each side, by pulling spring loaded J-pins (G) out. Picture Note: 48-Inch Deck used for photo purposes. 10.Put mower lift lever in the TRANSPORT (upper) position. 11.Slide mower out from under the tractor. M97162 G Downloaded f...
Page 70 - INSTALLING MOWER; Installing Mower
Installing Mower - Page 64 INSTALLING MOWER Installing Mower 1. STOP engine, LOCK park brake, push PTO switch down to DISENGAGE, turn key to the OFF position, and remove key. 2. Raise mower lift lever to TRANSPORT (upper) position. 3. Slide mower under the tractor and line up mower lift brackets wit...
Page 71 - TROUBLESHOOTING; Using Troubleshooting Chart; IF
Troubleshooting - Page 65 TROUBLESHOOTING Using Troubleshooting Chart If you are experiencing a problem that is not listed in this chart, see your Authorized Service Center for service. When you have checked all the possible causes listed and you are still experiencing the problem, see your Authoriz...
Page 73 - Tractor
Troubleshooting - Page 67 TROUBLESHOOTING Tractor Electrical IF CHECK Tractor Vibrates Too Much Attachment drive belts worn or damaged. Dirt on drive sheaves. Tractor Will Not Move With Engine Running Transmission hydraulic oil level low. Parking brake locked. Tractor Moves With Engine Running And H...
Page 74 - Mower
Troubleshooting - Page 68 TROUBLESHOOTING Mower IF CHECK Discharge Chute Plugging Belt installed incorrectly. Grass too wet. Grass too long. Restricted air flow. Check mower front-to-rear level. Engine rpm too low. Travel speed too fast. Patches Of Grass Uncut Travel speed too fast. Engine rpm too l...
Page 75 - Mower Loads Down Tractor
Troubleshooting - Page 69 TROUBLESHOOTING Requires High Effort To Lift And Latch Lift Handle Front draft arm on mower is adjusted too short, causing lift system to bind up. Mower Loads Down Tractor Engine rpm too low. Travel speed too fast. Debris wrapped around mower spindles. Bagging blades on mow...
Page 76 - STORING MACHINE; Storing Safely; Run machine for five minutes to dry belts and pulleys.
Storing Machine - Page 70 STORING MACHINE Storing Safely Preparing Machine for Storage 1. Repair any worn or damaged parts. Replace parts if necessary. Tighten loose hardware. 2. Clean under the deck. 3. Paint scratched or chipped metal surfaces to prevent rust. 4. Wash the machine and apply wax to ...
Page 77 - Preparing Engine For Storage; Running engine dry of fuel:; Start engine and allow to run until it runs out of fuel.; Add fuel and stabilizer mixture to tank:; Change engine oil and filter while engine is warm.
Storing Machine - Page 71 STORING MACHINE Preparing Engine For Storage NOTE: Properly preparing your tractor engine for storage will make it easier to start the following season. Engine storage procedure should be used if vehicle is not used for longer than 60 days. There are two satisfactory method...
Page 78 - engine oil in cylinders.; Removing Machine From Storage; Be sure all shields and guards are in place.
Storing Machine - Page 72 STORING MACHINE engine oil in cylinders. 5. Install spark plugs, but DO NOT connect spark plug wires. 6. Crank the engine for approximately five seconds to allow oil to be distributed. 7. Clean the engine and engine compartment. 8. Remove battery. 9. Clean the battery and b...
Page 79 - SPECIFICATIONS; Engine Manufacturer
Specifications - Page 73 SPECIFICATIONS Engine (Automatic-S2048) Engine Manufacturer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Kohler Engine Model Number . . . . . . . . . . . . . . . . . . . . . . . . . . . ...
Page 80 - Fuel System; Tires
Specifications - Page 74 SPECIFICATIONS Fuel System Fuel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . See Fuel in the Service Miscellaneous section Fuel Filter. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ...
Page 81 - Recommended Lubricants; (Specifications and design subject to change without notice.)
Specifications - Page 75 SPECIFICATIONS Mower Deck (48-inch) Blades-Rotary . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 Blade Bolt Torque . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ....
Page 82 - WARRANTY; LIMITED WARRANTY FOR NEW SCOTTS BRAND PRODUCTS
Warranty - Page 76 WARRANTY x LIMITED WARRANTY FOR NEW SCOTTS BRAND PRODUCTS Manufactured by John Deere (U.S. Only) A. GENERAL PROVISIONS - The warranties described below are provided by John Deere Company (“John Deere”) to the original purchasers of new Scotts Brand Products Manufactured by John De...
Page 84 - Tire Warranty
Warranty - Page 78 WARRANTY Tire Warranty John Deere warranty applies for tires available through the John Deere parts system. For tires not available through the John Deere parts system, the tire manufacturer’s warranty applicable to your machine may not apply outside the U.S. (See your John Deere ...
Page 87 - Limited Battery Warranty; Warranty Code
Warranty - Page 81 WARRANTY Limited Battery Warranty NOTE: Applicable in North America only. TO SECURE WARRANTY SERVICE The purchaser must request warranty service from a John Deere dealer authorized to sell John Deere batteries, and present the battery to the dealer with the top cover plate codes i...
Page 88 - INDEX
Index - Page 82 INDEX A Air Cleaner Elements, Checking and Cleaning .......................................................................................... 41 Air Intake Screen and Engine Fins, Cleaning .............................................................................................4...
Page 93 - SCOTTS SERVICE LITERATURE; Order Form; Title; Call
Scotts Service Literature - Page 87 SCOTTS SERVICE LITERATURE Order Form John Deere Distribution Center - Department S/P P.O. Box 186, Moline, IL 61266-0186 To order these publications, call 1-800-522-7448. If you want manuals or catalogs for equipment not shown on this list, provide the model numbe...
Page 95 - INVESTMENT IN QUALITY; Refer to your operator’s manual; • Your equipment model number.
Investment in Quality INVESTMENT IN QUALITY Please do not return this tractor to the store where you purchased it. Your Scotts tractor, designed and built by John Deere, is more than just a purchase, it’s an investment in quality. That quality goes beyond our equipment to your dealer’s parts and ser...