Page 3 - PRECAUTIONS FOR SAFE OPERATION; WARNING
2 PRECAUTIONS FOR SAFE OPERATION It is imperative that the user complies with this manual as it contains important safety advice. Items and procedures are described so that you can use this unit correctly and safely. If the precautions advised are followed, this will prevent possible injury to the u...
Page 6 - CAUTION
5 PRECAUTIONS FOR SAFE OPERATION Select a level and sturdy floor for installation. This precaution will prevent the unit from tipping. Improper installation may result in water spillage or injury from the unit tipping over. Do not install the unit at a place with the possibility of something falling...
Page 8 - CAUTIONS FOR USAGE
7 CAUTIONS FOR USAGE 1. Adequate space should be provided between the items inside the unit to allow air circulation. 2. Never store corrosive materials such as acid or alkali unless the container is completely sealed up. Corrosion may lead to failure of the unit in time. 3. In case condensation for...
Page 9 - ENVIRONMENTAL CONDITIONS
8 ENVIRONMENTAL CONDITIONS This equipment is designed to be safe at least under the following conditions (based on the IEC 1010-1): 1. Indoor use; 2. Altitude up to 2000 m; 3. Ambient temperature 5 o C to 40 o C 4. Maximum relative humidity 80% for temperature up to 31 o C decreasing linearly to 50%...
Page 10 - REFRIGERATOR COMPONENTS
9 REFRIGERATOR COMPONENTS MBR-1404GR 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17
Page 12 - Inside of front cover
11 REFRIGERATOR COMPONENTS Inside of front cover 1. Condenser filter: This filter is to prevent dust from plugging the condenser. Please clean the filter once a month. 2. Glow starter: This is for fluorescent light. Use “FG-4P” for replacement. 3. Remote alarm terminal: Refer to page 15. 4. Spacer (...
Page 13 - Control panel
12 REFRIGERATOR COMPONENTS Control panel 1. Alarm buzzer stop key (BUZZER): Press this key to temporarily silence the buzzer in the event that the alarm operates and buzzer sounds. 2. Temperature display (UPPER/LOWER): By pressing this key, the displayed temperature is changed; upper monitor bottle ...
Page 14 - INSTALLATION; Installation site
13 INSTALLATION Installation site To operate this unit properly and to obtain maximum performance, install the unit in a location with the following conditions: 1. A location not subjected to direct sunlight Installation in a location subjected to direct sunlight may lead to inadequate cooling. 2. A...
Page 15 - Installation
14 INSTALLATION Installation 1. Remove the packaging materials and tapes Remove all transportation packaging materials and tapes. Open the doors and ventilate the unit. If the outside panels are dirty, clean them with a neutral detergent and wipe it up with a wet cloth. 2. Adjust the leveling foot E...
Page 16 - BEFORE COMMENCING OPERATION; Preparation of monitor bottle; REMOTE ALARM TERMINAL
15 BEFORE COMMENCING OPERATION Preparation of monitor bottle Prior to the operation of the unit, fill the monitor bottles (upper and lower) with 10% glycerol (or other solution such as ethylene glycol) by the following procedure: 1. Remove the top and bottom drawer (or shelf). 2. Remove the monitor ...
Page 17 - Handling of containers
16 START-UP OF UNIT Follow the procedures for the initial and consequent operations of the unit. 1. Connect unit to dedicated power supply. Do not put any product in the unit at this time. 2. When the power is initially applied, the audible alarm may sound. This is normal. Press the BUZZER key...
Page 18 - OPERATING INSTRUCTIONS; Temperature display; Defrost cycles
17 OPERATING INSTRUCTIONS Temperature display The unit is set at the factory to obtain the proper temperature automatically (4 o C±1.5 o C). The high temperature alarm is preset at 6 o C. The low temperature alarm is preset at 2 o C. Table 1. Temperature display ● : Lamp ON ○ : Lamp OFF Operation Ke...
Page 19 - Alarm, safety function, and self diagnostic function
18 OPERATING INSTRUCTIONS Alarm, safety function, and self diagnostic function This unit has the alarm and safety functions shown in Table 2, and also self diagnostic function. Table 2 Alarm and safety functions Kind of alarm or safety Situation Indication Buzzer Safety operation High temperature al...
Page 20 - ROUTINE MAINTENANCE; Cleaning of cabinet
19 ROUTINE MAINTENANCE WARNING Always disconnect the power supply to the unit prior to any repair or maintenance of the unit in order to prevent electric shock or injury. Ensure you do not inhale or consume medication or aerosols from around the unit at the time of maintenance. These may be harmful ...
Page 21 - Cleaning of evaporating tray
20 ROUTINE MAINTENANCE Cleaning of evaporating tray 1. Remove the evaporating tray installed on the back of the frame by lifting the tray. 2. Wash away any accumulated dirt in the evaporating tray. 3. After cleaning of the evaporating tray, return it to the original position. Replacement of...
Page 22 - Calibration of temperature sensor
21 ROUTINE MAINTENANCE Calibration of temperature sensor The temperature sensors are attached to the monitor bottles. Follow the following instructions for proper calibration (zero adjustment): 1. Remove the monitor bottle cover as shown in the figure. 2. Remove the sensor to be calibrated from th...
Page 24 - SPECIFICATIONS; PERFORMANCE
23 SPECIFICATIONS Name Blood Bank Refrigerator Model MBR-1404G MBR-1404GR External dimensions W1440 x D830 x H1950 (mm) Internal dimensions W1320 x D697 x H1500 (mm) Effective capacity 1287 L Exterior Painted steel Interior Painted steel Door Double layer pair glass/steel p...
Page 25 - Safety check sheet
24 CAUTION Please fill in this form before servicing. Hand over this form to the service engineer to keep for his and your safety. Safety check sheet 1. Refrigerator contents : Risk of infection: Risk of toxicity: Risk from radioactive sources: (List all potentially hazardous materials that have bee...
