Sanyo LNS-W31A - Manual
Sanyo LNS-W31A – Manual, read for free online in PDF format. We hope this helps you resolve any issues you may have. If you have further questions, please contact us through the contact form.
Table of Contents:
- Page 5 – LENS LOCK LATCHES
- Page 7 – REMOVE THE LENS
- Page 8 – MOUNT THE LENS; Correcting the focus
Following checks and confirmations should be taken for safety.
C h e ck t h e fo l l ow i n g t h i n g s by t h e t i m e o f t h e c a b i n e t a s s e m bl y a f t e r t h e l e n s
replacement.
1. Check the lens is securely fixed.
2. Check the proper wiring and the wires are fixed properly.
3. Check each connector is connected properly.
4. Check no wiring is tangled on the gear of lens motor or the other mechanical parts.
5. Check no parts is missing, or no mounting part is loose.
LCD PROJECTOR LENS
MODEL LNS-T31A/W31A/T32
LENS REPLACEMENT PROCEDURE
NOTES ON LENS REPLACEMENT
Lens replacement should be performed by the qualified service personnel.
It should be followed by this procedure precisely.
Before attempt to replace the lens, confirm the model number (both the LCD
projector and the lens) and use the proper lens.
The lens cover is on the lens for protection. Be sure to remove the lens cover
before installation.
When installing or removing the lens, be careful not to stain, scratch or
damage the lens.
If you have any questions, contact the dealers.
Following parts are contained in the packing.
1AA6P1P3188A- (ICYDA-A)
PARTS LIST
●
LENS
●
LIGHT-BLOCK SHEET BASE
●
DRIVER (3 mm, Green)
●
DRIVER (4 mm, Yellow)
●
LIGHT-BLOCK SHEET For LNS-T31A
For LNS-W31A
For LNS-T32
1 piece
1 piece (Part No. 610 310 8001)
1 piece (Part No. 610 287 7328)
1 piece (Part No. 610 275 6029)
1 piece Type PB1 (Part No. 610 310 7950)
1 piece Type PC1 (Part No. 610 310 7967)
1 piece Type PF1 (Part No. 610 310 7974)
NOTE; Lens installation is different in cabinet design and lens attachment method
(Type A, B and C). Before installation the lens, check cabinet design and
proper installation should be made.
"Loading the manual" means you need to wait until the file loads and becomes available for online reading. Some manuals are very large, and the time they take to appear depends on your internet speed.
Summary
4 MOUNT THE LENS (See Figure-5) Remove protective caps (front and back) on the lens. Mount the lens on lens mounting bracket with Upper 2 screws. (locate motor on left side). Use the driver (4 mm, Yellow) included with the lens to fasten the screws. Remove the lower 2 screws on the Lens. (Lower 2 sc...
- 7 - Turn the lens cover to counter-clockwise and pull ittoward front and remove the Lens Cover.Remove 2 Screws-A.Remove the front cabinet R E M OV E T H E L E N S C OV E R A N DFRONT CABINET 1 1. 2. 2 REMOVE THE LIGHT-BLOCK SHEET BASEAND LIGHT-BLOCK SHEET Perform the steps to for lens replacement....
- 8 - LENSATTACHMENT Part No. (610 275 6029) 4 MOUNT THE LENS Remove protective caps (front and back) on the optional lens.Mount the lens on the lens attachment with 4 Screws.Connect the lens motor lead connector to the socket on the lens attachment. (Motor DrivenLens only.)Grasp the Lens Lock Lever...
