Sanyo 42LM5RTC - Manual - manualsarea.com

Page 4 - ABOUT THIS MANUAL; Interactive Touchscreen; running under; CONTACT INFORMATION

4 ABOUT THIS MANUAL This manual is intended as a reference guide for the Interactive Touchscreen running under Windows XP™ or Windows Vista™. This User Manual provides the information needed to set up the touchscreen. In addition, this manual describes basic technical information about the touchscre...

Page 5 - INTRODUCTION; Ma7 Driver; COMPATIBILITY

5 INTRODUCTION This manual will explain the workings and setup of the touchscreen fitted to your display. An explanation of the monitor and its workings is covered in the Monitor Manual that came with this product. The following pages will tell you how to install the software needed by the touchscre...

Page 6 - INSTALLATION

6 INSTALLATION LOADING THE TOUCH DRIVER SOFTWARE ONTO PC 1. Switch on monitor Do not plug the touchscreen interface cable into your computer . 2. Insert the ‘ Information & Touch Software installation CD’ into the PC and follow the automatic installation instructions. If the installation does no...

Page 9 - The; Reset

9 The mouse pointer will not respond to a touch until it has been enabled in the Output section of the Control Program. Details of this will follow later in this manual. The Reset button loads fresh data from the touchscreen. This is used as a reference for detecting any new touches. This may be nec...

Page 10 - ADJUSTING THE TOUCH SENSITIVITY LEVEL; to approximately two thirds by dragging the bar with your

10 ADJUSTING THE TOUCH SENSITIVITY LEVEL Automatic Setup When you receive your unit, the sensitivity settings will have been optimised when the unit was manufactured. These settings should only be altered if you are experiencing problems such as an electrically noisy environment. Contact your suppli...

Page 12 - CALIBRATION; Calib; When each of these targets is displayed, touch and hold; You must touch all three targets in turn

12 CALIBRATION 1. Select the Calib tab as shown below (Fig 5), click the 'Start Calibration' box. Fig 5 2. You will see the following screen (Fig 6); there are three targets to touch in total, like the one shown below: Fig 6 3. When each of these targets is displayed, touch and hold your finger on t...

Page 13 - enables mouse pointer movement but no button movement when

13 SETTING THE TOUCH OUTPUT TO SUIT THE APPLICATION PROGRAM 1. Select the Output tab. Fig 7 2. Select the mouse control required for your application (Fig 7). To enable the touch function on the screen, tick the Enable check box. 3. No action selects no mouse pointer movement or button pressing when...

Page 14 - You must now save the settings

14 You must now save the settings Fig 8 1. (Fig 8) Click on file. 2. Click on save to save the current settings. When the touchscreen driver has been set up and there is no requirement to change it.

Page 15 - DIAGNOSTICS AND FREQUENTLY ASKED QUESTIONS; setup. Contact your supplier for more information.

15 DIAGNOSTICS AND FREQUENTLY ASKED QUESTIONS Testing the Hardware with ‘Graph’ 1. Select the Graph tab. Fig 9 2. Run a finger around the sensor, the effect of the finger on nearby wires can be seen by a visible movement on the indicators (Fig 9), each representing one wire. The algorithm in the dri...

Page 16 - MONITOR MODE; Enable Selection Control; in the output section. When the finger is removed for a few; Advanced; box is ticked the; Fig 11 Fig 12

16 MONITOR MODE Fig 10 1. This section is used to check the output of the touchscreen over the whole display area represented by the white box in the centre. It is useful in checking for any dead areas on the touchscreen and the performance of the touchscreen being able to follow the finger accurate...

Page 17 - USING EDGE ENHANCEMENT; Edge Gain; DELAYED STARTING OF THE DRIVER OUTPUT; file. This is found in the same directory as the

17 USING EDGE ENHANCEMENT 1. To allow easy access to the sliders and buttons at the edge of the display, the cursor can be positioned nearer the edge of the screen. The amount of enhancement can be adjusted via the screen shown. Fig 13 2. Each of the sliders represents one edge of the sensor; the de...

Page 18 - FAULT FINDING GUIDE

18 FAULT FINDING GUIDE The following are some possible reasons why the touch screen might not work. If they do not solve your problem or you have a situation not covered please contact your supplier. DRIVER DOES NOT SEE THE TOUCHSCREEN Touchscreen on a different comm port than the one selected. The ...

Sanyo 42LM5RTC - Manual

Table of Contents:

Summary

Other Sanyo Models