Page 2 - CONTENTS
CONTENTS 1. PRECAUTIONS 1-1. SAFE PRECAUTIONS .......................................................................................................................................... 1 1-2. PRECAUTIONS UPON INSTALLATION .................................................................................
Page 3 - PCB CIRCUIT DIAGRAM
CONTENTS 8. BLOCK DIAGRAM ................................................................................................................................... 47 9. WIRING DIAGRAM 9-1. PCB ASSY’ LAYOUT ......................................................................................................
Page 7 - ■ How to Level the Unit; Install the unit with 10cm or more
4 Cauti ution on Tighten the lock nut after the leveling. If not, it could generate vibrations & noises. Lock Nut Leveling Bolt Spanner Flat Head Screwdriver ■ How to Level the Unit 1.Select an installation place. Install the unit with 10cm or more clearance from its surrounding walls. 2.Check i...
Page 8 - THE FEATURE OF PRODUCT
5 2. THE FEATURE OF PRODUCT 2-1. SPECIFICATIONS WASH TYPE FRONT LOADING TYPE DIMENSION NET W 598mm X D 450mm X H 844mm GROSS W 668mm X D 576mm X H 890mm WATER PRESSURE 50 kPa ~ 800 kPa WEIGHT NET 66 kg GROSS 69 kg WASH and SPIN CAPACITY 5.2 kg (DRY LAUNDRY) POWER CONSUMPTION WASHING 220V 180W 240V 1...
Page 11 - PRODUCT SPECIFICATIONS
8 3. PRODUCT SPECIFICATIONS 3-1. OVERVIEW OF THE CONTROL PANEL
Page 14 - Bubble-detecting function operating process
11 8) Fuzzy washing function (weight-sensing) ● After fi nishing initial water supply, when the fall of the water level needs supplementary water supply, Sensing function perceives the weight with the supplementary water supply numbers and starts to work. Under the course of Cotton, or Coloureds, if ...
Page 15 - Unbalance detecting & laundry balance positioning system
12 10) Unbalance detecting & laundry balance positioning system ķ Just before the hydrating process and just after reversal rotation for balancing laundry position, this function is carried out ĸ The initial 6 sec is the period of reversal rotation for balancing laundry position , Drum rotates 5...
Page 17 - ) The water supply control at each process cycle; ) The water level data at each course
14 3) The water supply control at each process cycle Model Process cycle WF-R1061,WF-R861 Pre Washing Cold water 5L/min Washing Cold water 10L/min + (Hot water 10L/min) Rinse Cold water 10L/min Final rinse Cold water 10L/min + Cold water 5L/min 4) The water level data at each course unit:Khz Model C...
Page 18 - ) The other water level data
15 5) The other water level data unit:Khz The water data unter each conditon WF-R1061,WF-R861 1st water supply (only preparation) 25.50 1st water supply level to washing tub Overfl ow error 21.50 The water supplied reach 2/3 of door Bubble detectingatwashing/rinse/dehydrating 24.50 Bubble -detecting ...
Page 21 - ALIGNMENT AND ADJUSTMENTS; Water Level
18 4. ALIGNMENT AND ADJUSTMENTS 4-1. GENERAL ERROR FUNCTION 1. An occurrence of an Error will make a sound of error melody for 5sec and continuously show one of the Error Displays from the following errors. (But, Fault Check Led will fl ash for 0.5sec.) 2. All of the steering parts will be off at tha...
Page 24 - ASSEMBLY AND DISASSEMBLY
21 5. ASSEMBLY AND DISASSEMBLY 5-1. TOOLS FOR DISASSEMBLY AND ASSEMBLY NO. TOOL 1 Box driver 10mm 13mm 19mm Motor (1), Balance (5), 2 holes of each left and right of the shock absorber 1 Pulley hole 2 Double-ended spanner 10, 13,19mm Replaceable for the box driver.Since the bolt runs idle when the b...
Page 25 - sensor pressure
22 Part Name Descriptive Picture How To Do ASS’Y- COVER TOP ķ Remove the two screws holding the Top Cover at the back of the unit. ĸ Remove the top-cover through push ing and pulling. Ĺ Then, the Water (Pressure) Sensor, Noise Filter and Water Valve can be replaced. 5-2. ASSEMBLY AND DISASSEMBLY War...
Page 26 - FRAME
23 Part Name Descriptive Picture How To Do FRAME FRONT ķ Remove the Top Cover and the Ass’y Drawer. ĸ Remove the two screws on the front of the control panel. Ĺ Remove the two screws on the plate(u). ĺ Remove the control panel by disconnect ing the connector that connects PCB to the wire-harness.
Page 28 - BEL T
25 Part Name Descript ive Picture How To Do BEL T MO TOR Before removing the belt, should be opened the Cover Bottom. ¤ Remove the belt before the re-assembly. ¤Ł Ensure the belt is placed on the center of the motor pulley. <Belt Assembly> Hang the belt on the motor pulley( ¤ ) before placing ...
Page 30 - Hinge
27 Part Name Descriptive Picture How To Do Door- Hinge ķ Remove the fi xing screws holding the Door-Glass. ĸ Separate the glass. Ĺ After removing the two screws holding the Holder Glass, replace the Door Hinge. ĺ After putting them back together, check if the screws holding the Door Hinge is fastened...
Page 32 - Heater
29 Part Name Descriptive Picture How To Do Door S/W ķ Open the Door. ĸ Remove the Spring Diaphragm and separate the Diaphragm from the Frame Front. - Insert the fl at head screwdriver and pry up the spring to remove the Spring Diaphragm. - The Diaphragm could get damaged when taking it out. So, unsea...
Page 34 - Caution for the Repair and Replacement; work contacting to PCB is executed.
31 6. TROUBLE DIAGNOSIS 6-1. TROUBLE DIAGNOSIS - As the micom wash machine is confi gured of the complicate structure, there might be the service call. Below information is prepared for exact trouble diagnosis and suitable repair guide. Caution for the Repair and Replacement Please follow below instr...
Page 39 - Micom Number 31 Is; YES; Check The IC6
36 6-2-6. Driving Part Checking ƹ Confi rm The Output Of DC5V, When The Every Part Of Micom Number Check, According To The Some Problem Condition ex) When The Drain Is Not Operating But Pump Motor Is Operating, Check The 5Voltage Of Micom Ć Check The Micom 18th In The Above Method When The Cold Water...
Page 43 - EXPLODED VIEWS AND PARTS LIST
40 F0064 D0004 D0112 D0061 D0075 C0103 R0065 C0058 C0115 R0019 F0065 P0036 R0036 R0025 C0002 C0043 C0044 7. EXPLODED VIEWS AND PARTS LIST 7-1. EXPLODED VIEWS OF TOP(FRONT)
Page 49 - VAL; UNIVERSAL; MAIN; CPU
46 8. BLOCK DIAGRAM MAIN PBA COLD-VALVE PRE- VAL VE DRAIN PUMP DOOR-LOCK DOOR-LOCK SIG UNIVERSAL MOTOR MO TO R CW/CC W CONTR O L RELA Y ML MR MAIN MICOM DR IVE CONTR O L TR IAC DR IVE CONTR O L RELA Y WATER LEVE L SENSO R WA TER T HERMI S TO R HEAT SINK THERMI STOR O S CI LLA TI O N C IRC UI T RE SE...
Page 54 - CIRCUIT DESCRIPTION
Page 60 - REFERENCE INFORMATION; WF
57 13. REFERENCE INFORMATION 13-1. MODEL NAME Buyer Drum machine classification according to type: WF(Washer Front Loading) WD(Washer&Drier) RPM Notation 800RPM: 8 1000RPM:10 1200RPM:12 1400RPM:14 INTRO YR 2006 Service Code Actual Model Name in the Market BOM Model Code WF R 10 6 1 1 YLP / A lph...
Page 70 - Printed in Korea
© Samsung Electronics Co., Ltd. April. 2006 Printed in Korea This Service Manual is a property of Samaung Electronic Co.,Ltd.Any unauthorized use of Manual can be punished under applicable inter-national and/or domestic law.