Page 3 - IMPORTANT SAFEGUARDS
2 IMPORTANT SAFEGUARDS Caution Power source is indicated on the rear of the set. It contains high-voltage parts. If you remove the cover, it may cause fire or electric shock. Do not remove the cover by yourself. (Control switches are at the front of the monitor). 1. Read Instructions : All the safet...
Page 6 - FCC & ICES Information; Warning; User-Installer Caution
FCC & ICES Information Warning This equipment has been tested and found to comply the limits for a class B digital device, pursuant to part 15 of the FCC Rules and ICES-003 of Industry Canada. These limits are designed to provide reasonable protection against harmful interference when the equipm...
Page 7 - Contents
6 Contents IMPORTANT SAFEGUARDS 2 1. System Components and Installation 7 1-1. SYSTEM Components 7 1-2. SYSTEM CONFIGURATION 8 1-3. Individual Component Installation 9 1-4. Basic System Installation 19 2. Connecting Peripheral Devices 20 2-1. To connect a PIR Sensor 20 2-2. To connect a VCR 20 3. Sy...
Page 8 - System Components and Installation; ACCESSORIES
7 1. System Components and Installation 1-1. System Components ✳ If you have purchased only a monitor, you should directly purchase every component exceptaccessories. STANDARD CAMERA CAMERA HOUSING MOUNTING BRACKET DOME CAMERA CAMERA CABLE CAMERA MOUNT BRACKET ALARM CABLE INSTALLATION MANUAL POWER C...
Page 21 - Connecting Peripheral Devices
20 2. Connecting Peripheral Devices 2-1. To Connect a PIR Sensor - An additional PIR sensor or external sensor can also be connected. - The additional PIR sensor can be connected as shown in the above graphic. - Sensor's trigger signal is NO (Normal Open). - Sensor is not supplied. (Sold separately)...
Page 23 - Part Names and Functions
22 4. Part Names and Functions 4-1. Camera Standard Camera Lens It has a focal length of 3.8mm and makes it possible for you to observe a relatively widearea. Microphone Capable of picking up all sound in the vicinity of the camera location and transmitting tothe monitor. Camera fitting groove Enabl...
Page 25 - Monitor ON/OFF and Alarm Reset; ALARM RESET; VOLUME
24 4-2. Monitor Monitor Controls - Front Panel ① Monitor ON/OFF and Alarm Reset MONITOR ON/OFF In the monitor screen OFF mode, the monitor switches to the power save mode outputtingonly the VCR OUT signal. ✳ When an alarm occurs, while in the power save mode, Monitor screen turns onautomatically. At...
Page 28 - AC IN
27 Monitor Controls- Back Panel ① AC IN Power input jack. ② CAMERA IN A 6 Pin Modular jack used for video input and camera power input. Pin Configuration of the 6 Pin Connector is as follows. PIN NUMBER SPEC 1 ALARM_IN 2 VIDEO_IN 3 GND 4 GND 5 AUDIO_IN 6 12V DC
Page 29 - CAMERA OUT; ALARM; ALARM OUT; MONITOR OUT
28 ③ CAMERA OUT CAMERA OUT: This jack means a video output signal of each camera. You can use it whenconnecting to an external device. ④ VCR IN/OUT VIDEO IN : VCR video input jack. VIDEO OUT : Video recording output jack. ⑤ AUDIO IN/OUT AUDIO IN : VCR audio input jack. AUDIO OUT : Audio recording ou...
Page 30 - Setting Up the System
29 Menu Setup • Use this to set data for System operation, such as Time,Date, Alarm, etc.Whenever the MENU key is pressed, the Main Menuwill be displayed (except when in the ALARM Mode).Move the cursor to the item to be set, ` ▲ a ` ▼ a then press the ENTER key to display the Sub Menu.In the Menu mo...
Page 31 - AUTO SWITCHER Setup
30 4.AUTO SWITCHER Setup • Use this to set Channel Switching time while in the Auto Switcher and PIP modes. • Select the desired channel, ` ▲ a ` ▼ a then use the ` ˇ a ` ˆ a keys to set the Switching time. • Switching time can be between 0 to 30seconds. • When the switching time is set to "0...
Page 32 - VIDEO ADJUSTMENT Setup
31 6. VIDEO ADJUSTMENT Setup • Use to set up items concerning video signals suchas CONTRAST, BRIGHT, etc. • Select the item to change, ` ▲ a ` ▼ a then use the ` ˇ a ` ˆ a keys to change the numerical value. A numerical value can range from 0 to 100. • "EXIT" will allow you to choose whether...
Page 35 - Technical Specifications
34 6.Technical Specifications SSC-21M : Monitor Specifications Model Name SSC-21M Broadcast System Standard NTSC Picture Tube 21 Inch CRT, 0.71mm stripe pitch, 90 ° deflection Visible screen size: 50.8 cm (20 inch) (measured diagonally) Horizontal Resolution 450 lines Video Input/Outputs 4 Channel I...
Page 38 - Memo