Page 2 - Network Video Recorder; User Manual
Copyright ©2014 Samsung Techwin Co., Ltd. All rights reserved. Trademark is the registered logo of Samsung Techwin Co., Ltd. The name of this product is the registered trademark of Samsung Techwin Co., Ltd. Other trademarks mentioned in this manual are the registered trademark of their respective co...
Page 3 - English; IMPORTANT SAFETY INSTRUCTIONS; Standards Approvals; overview
English _3 ● OVER VIEW IMPORTANT SAFETY INSTRUCTIONS Read these operating instructions carefully before using the unit. Follow all the safety instructions listed below. Keep these operating instructions handy for future reference. 1) Read these instructions. 2) Keep these instructions. 3) Heed all w...
Page 4 - BEFORE START; Warning; Battery
4_ overview overview BEFORE START This manual provides operational information necessary for using the product and contains a description about each component part and its function as well as menu or network settings.You have to keep in mind the following notices : • SAMSUNG retains the copyright on...
Page 5 - Operating Temperature
English _5 ● OVER VIEW Operating Temperature The guaranteed operating temperature range of this product is 0°C ~ 40°C (32°F ~ 104°F).This product may not work properly if you run right after a long period of storage at a temperature below the guaranteed one.Prior to using a device that has been stor...
Page 6 - CONTENTS; OVERVIEW
6_ overview overview CONTENTS OVERVIEW 3 3 Important Safety Instructions 4 Before Start 6 Contents 8 Features 10 Part Names and Functions (Front) 11 Part Names and Functions (Rear) 12 Remote Control INSTALLATION 13 13 Checking the installation environment 14 Rack Installation 14 HDD Addition CONNECT...
Page 8 - FEATURES
8_ overview overview FEATURES The product records video and audio from network cameras to a hard disk, and enables playback from the hard disk.It also provides remote monitoring environment for video and audio over the network using a remote computer. • User-friendly UI • VGA, 4CIF, record in a max ...
Page 9 - Package Contents
English _9 ● OVER VIEW Package Contents Please unwrap the product, and place the product on a flat place or in the place to be installed. Please check the following contents are included in addition to the main unit. '9 6516 1(7:25.9,'(25(&25'(5 REC HDD ALARM NETWORK BACKUP POWER NVR Remote Cont...
Page 10 - c b
10_ overview overview PART NAMES AND FUNCTIONS (FRONT) Part Names Functions LED Indicator REC : Lights on when recording is in progress. HDD : Displays the normal access to HDD. LED turns on when accessing the hard disk. ALARM : Lights on when an event occurs. NETWORK : Displays both network connect...
Page 12 - REMOTE CONTROL; Using the Numeric buttons; Changing the Remote Control ID
12_ overview overview REMOTE CONTROL Using the Numeric buttons 1. Select a number between 1 and 4. 2. Move to the selected channel number. Changing the Remote Control ID Remote control’s ID and NVR’s ID should be matched for proper operation. 1. Press the [ ID ] button of the remote control and chec...
Page 13 - installation; Please take note of the followings before using this product.; CHECKING THE INSTALLATION ENVIRONMENT
English _13 ● INST ALLA TION installation Please take note of the followings before using this product. • Do not use the product outdoor. • Do not spill water or liquid in the connection part of the product. • Do not impose the system to excessive shock or force. • Do not pull out the power plug for...
Page 14 - RACK INSTALLATION; HDD ADDITION; Cautions when installing a HDD
14_ installation installation RACK INSTALLATION Install the Bracket-Rack as shown in the figure, and then fasten the screws on both sides (2 screws on each side). ` Fix the screws not to be loosened by vibrations. HDD ADDITION Make sure to unplug the power cord from the wall outlet to prevent possib...
Page 15 - When you mount an HDD
English _15 ● INST ALLA TION When you mount an HDD 1. Unfasten the screws on the side and in the rear and remove the cover. 2. Unfasten the screws on the HDD bracket and remove the bracket. ` Press the handle on both sides of the bracket and pull it forward. The main body and the bracket will separa...
Page 17 - connecting with other device; CONNECTING TO AN EXTERNAL DEVICE
English _17 ● CONNECTING WITH OTHER DEVICE connecting with other device CONNECTING TO AN EXTERNAL DEVICE J ` Unrated or improper power source may cause damage to the system. Ensure that you use only the rated power source before pressing the POWER button. G 1& 12 12 12 &20 &20 &20 AL...
Page 18 - CONNECTING THE USB
18_ connecting with other device connecting with other device CONNECTING THE USB 1. On the front of the product, there is a USB port. 2. You can connect a USB HDD, USB CD/DVD player, USB memory or mouse to the USB port. 3. If a USB HDD is connected to the system, recognition and settings are availab...
Page 19 - CONNECTING THE ALARM INPUT/OUTPUT
English _19 ● CONNECTING WITH OTHER DEVICE CONNECTING THE ALARM INPUT/OUTPUT The Alarm In/Out port at the back is composed of the following. • ALARM IN 1 ~ 4 : Alarm Input Port • ALARM OUT 1 ~ 3 : Alarm Output Port Open collector output device Mechanical switch I/O 1.2KΩ GND VDD GND or G 1& 12 1...
Page 20 - CONNECTING THE NETWORK; Network connection via router; NETWORK
20_ connecting with other device connecting with other device CONNECTING THE NETWORK M ` For more information about network connection, refer to " Network Configuration ". (Page 76) Network connection via Ethernet (10/100BaseT) Network connection via router G 1& 12 12 12 &20 &20 ...
Page 21 - Connecting to Internet through PPPoE; PnP mode
English _21 ● CONNECTING WITH OTHER DEVICE Connecting to Internet through PPPoE Connecting the network camera PnP mode G 1& 12 12 12 &20 &20 &20 ALARM OUT ALARM IN Network Camera ex) IP : 192.168.231.20 Network Camera ex) IP : 192.168.231.40 Network Camera ex) IP : 192.168.231.30 Net...
Page 22 - Manual mode
22_ connecting with other device connecting with other device Manual mode G 1& 12 12 12 &20 &20 &20 ALARM OUT ALARM IN Switch Switch Network Camera Network Camera ex) IP : 192.168.1.20 Network Camera ex) IP : 192.168.1.10 Network Camera Network Camera Network Camera ex ex)) IP IP :: ...
Page 23 - GETTING STARTED; Starting the system; Easy Setup; live
English _23 ● LIVE GETTING STARTED Starting the system 1. Connect the power cable of the NVR to the wall outlet. 2. You will see the initialization screen.The initialization process will last about 2 minute. If a new HDD is installed, the initialization process may take longer. Easy Setup This setti...
Page 24 - Shutting Down the System
24_ live live Shutting Down the System 1. Press the [ POWER ] button for your remote controller or select < Shutdown > in the live screen menu. 2. The “ Shutdown ” confirmation pop-up window will appear. 3. Using the directional button on your remote control, select < OK > and press the ...
Page 25 - LIVE SCREEN CONFIGURATION; Icons on the Live Screen
English _25 ● LIVE LIVE SCREEN CONFIGURATION Icons on the Live Screen You can check the status or operation of the NVR with the icons on the live screen. Name Description Current Date, Time Displays the current time and date. b Login Information When you are logged in, the " LOG ON " icon wi...
Page 27 - Error Information; Live Screen Menu
English _27 ● LIVE Error Information • If the built-in HDD is not connected, the “NO HDD” icon ( ) will be displayed in the top left corner. In this case, make sure you contact the service center for assistance as this may cause a failure of recording, playback or backup. • If the cooling fan does n...
Page 28 - Single Mode Menu
28_ live live Single Mode Menu The single mode menu is available only in Single Mode.If the menu is displayed as < Screen Mode > in the single screen, it is displayed as a < Full Screen > in the menu where only one channel is selected in the split screen. Menu Description Full Screen Sel...
Page 29 - Split Mode Menu
English _29 ● LIVE Split Mode Menu In Live split mode, right-click to display this context menu as shown.The context sensitive menu in split mode differs, depending on the login/logout status. Menu Description Screen Mode Select a screen mode for the Live screen.Refer to “ Live screen mode ”. (Page ...
Page 31 - View the Launcher Menu; b c
English _31 ● LIVE View the Launcher Menu The Launcher menu appears on the bottom of the live screen. 1. Select < Show Launcher > in the context menu of the Live screen. 2. Move the cursor to the bottom and click a desired item in the Launcher menu. M ` If no input is entered for 10 seconds, t...
Page 32 - LIVE SCREEN MODE; Method for displaying screen mode; Auto screen switching
32_ live live LIVE SCREEN MODE Four live videos are displayed in the three split screens. Method for displaying screen mode If you want to change the split mode, select a screen mode suggested in the launcher menu or right click with the mouse button and select a split mode in the screen mode menu.P...
Page 33 - Channel information; Channel Setting; Switching to Single Mode
English _33 ● LIVE Channel information Select the < CH Info > in the live screen menu to check the status of camera connection to each channel. Channel Setting You can display the channel in a desired area of a split screen. 1. Place the cursor over the camera name of each channel to display t...
Page 34 - Record Status
34_ live live Live Status Select < Live Status > from the live screen menu to display status and transfer information of connected camera to each channel. • Model : Displays the camera model name connected to each channel. • Status : Displays the status of camera connection set to each channel...
Page 36 - POE STATUS; AUDIO ON/OFF in Single mode
36_ live live POE STATUS In the live screen, you can see the PoE status of each port. 1. Select the < PoE Status >. PoE status view window is displayed. • Consumption(W) : Displays the power consumption in PoE. - 0 : No device is connected to the port or a device is using its own power supply....
Page 37 - EVENT MONITORING
English _37 ● LIVE FREEZE This is available only in Live mode, this pauses playing the Live image temporarily. 1. Press the [ FREEZE ] button on your remote control or click < > in launcher mode. Video playing is paused. 2. Press the [ FREEZE ] button on your remote control or click < > ...
Page 38 - PTZ CONTROL; PTZ device; Getting started with PTZ operations
38_ live live M ` Press the [ ALARM ] button or select < Stop Alarm > to initialize the alarm output status and cancel the event function. ` If an alarm is output with the pre-event and post-event times specified together with the event recording settings, the event recording will perform acco...
Page 39 - Using the PTZ camera
English _39 ● LIVE Using the PTZ camera You can use a single PTZ camera to perform the Pan, Tilt and Zoom operations to monitor multiple places, and configure the custom settings of the presets in a desired mode. 1. Open the < PTZ Control > menu. The < > icon in the left bottom of the sc...
Page 40 - Preset; To add a preset; If you want to change or delete the preset name
40_ live live Preset Preset is a specific position remembered by the PTZ camera. You can use the Preset function to define up to 255 presets for a single PTZ camera. To add a preset 1. Check the preset checkbox. 2. Select < >. The virtual keyboard will appear on the screen. Use it to provide t...
Page 41 - SYSTEM SETUP; menu setup
You can setup the system, devices, and options for recording, event and network. SYSTEM SETUP You can setup Date/Time/Language, User, System Properties and Log. Date/Time/Language Setting the Date/Time/Language You can check and setup the current Date/Time and time related properties, as well as the...
Page 43 - User; Setting the Administrator
User You can set permissions of each user over the NVR's specific function and settings. Setting the Administrator You can set and change Administrator's ID and password.The administrator can use and set all menu items and functions. [ MENU ] Ö [ ENTER ] Ö ▼ Ö < Menu > Ö [ ENTER ] Ö < Syste...
Page 44 - User setting
User setting You can create a group or set permissions for each group.You can add a user and edit the registered user information. [ MENU ] Ö [ ENTER ] Ö ▼ Ö < Menu > Ö [ ENTER ] Ö ►▼ Ö < System > Ö < User > Ö [ ENTER ] Ö ▼► Ö < User > Ö ▲▼◄► Ö [ ENTER ] If you want to add a ...
Page 45 - Setting Permissions
If you want to register a user 1. Click on the [ ] button to launch the user addition popup window. To add a user, click on < OK >. 2. Select a group.When registering a user, the selected group will be automatically registered. ` A group can be changed after inputting all required information....
Page 46 - If the user has restricted access; To change the user password
• Restriction on Network Access : Restricts remote access from a < Restricted Access > network. - All Network : Restricts all access instances via Network Viewer and Web Viewer. - Web Viewer : Restricts access via the Web Viewer. • Auto Log out : A user will be automatically logged out if ther...
Page 47 - System Management; Checking the System Information
System Management You can check the system version, update to a newer version, as well as data backup and initialization. Checking the System Information You can check the current software version and MAC address before proceeding with the upgrade. [ MENU ] Ö [ ENTER ] Ö ▼ Ö < Menu > Ö [ ENTER...
Page 49 - Settings
Settings You can copy and import the NVR settings by using a storage media. [ MENU ] Ö [ ENTER ] Ö ▼ Ö < Menu > Ö [ ENTER ] Ö < System > Ö ►▼ Ö < System Management > Ö [ ENTER ] Ö ▼► Ö < Settings > Ö [ ENTER ] Ö ▲▼◄► Ö [ ENTER ] • Storage Device : Shows the connected storage ...
Page 50 - Log Information; Checking the system log
Log Information You can browse logs on the system and events. Checking the system log System Log shows log and timestamp on every system start up, system shutdown, and changes on system settings. [ MENU ] Ö [ ENTER ] Ö ▼ Ö < Menu > Ö [ ENTER ] Ö < System > Ö ►▼ Ö < Log Information >...
Page 51 - Checking the event log; Checking the backup log
Checking the event log You can search recorded events including alarms, camera events and video loss.It also shows the log and its timestamp. [ MENU ] Ö [ ENTER ] Ö ▼ Ö < Menu > Ö [ ENTER ] Ö < System > Ö ►▼ Ö < Log Information > Ö [ ENTER ] Ö ▼► Ö < Event Log > Ö [ ENTER ] Ö...
Page 52 - SETTING THE DEVICE; Camera; To register a camera
SETTING THE DEVICE You can setup Camera, Storage Device and Monitor. Camera To register a camera You can register a network camera for each channel and make connection between. [ MENU ] Ö [ ENTER ] Ö ▼ Ö < Menu > Ö [ ENTER ] Ö ▼ Ö < Device > Ö ► Ö < Camera > Ö [ ENTER ] Ö ▼ Ö < ...
Page 59 - Camera Setting
Event You can set details of the event. • Available events (camera) : It shows the list of all the events supported by a camera by using the ONVIF protocol. • NVR supported events : You can map the list of events supported by a camera to events that the NVR can detect. There is no default value. It ...
Page 60 - Setup
M ` If you change the settings of a specific profile for each model, the effective range of the baud rate may be changed accordingly.Ex) if you set the baud rate of the first profile to 30fps, the send rate of the second profile will be changed to 15fps. ` Menu items except Codec, Resolution, Transf...
Page 63 - Live Setting
Live Setting You can change the live transfer settings of the network camera. [ MENU ] Ö [ ENTER ] Ö ▼ Ö < Menu > Ö [ ENTER ] Ö ▼ Ö < Device > Ö ► Ö < Camera > Ö [ ENTER ] Ö ▼► Ö < Live Setup > Ö [ ENTER ] Ö ▲▼◄► Ö [ ENTER ] • Live Replacement : You can select the live profil...
Page 65 - Storage Device
Storage Device You can check information on storage devices. Device/Format You can check storage devices and their capacity, usage as well as status.Devices available are HDD, and USB devices (Memory, HDD). [ MENU ] Ö [ ENTER ] Ö ▼ Ö < Menu > Ö [ ENTER ] Ö ▼ Ö < Device > Ö ►▼ Ö < Stor...
Page 66 - HDD Alarm Setting
• Format : Select a device and click on format after which a format confirmation window appears.Click on the < OK > button to format the selected storage device. J ` Formatting will delete all the recording data that has been saved. Be careful. ` While formatting is ongoing, you cannot record ...
Page 67 - Remote Devices; Monitor settings
Remote Devices You can adjust the ID for a remote control to be used in connection with NVR. [ MENU ] Ö [ ENTER ] Ö ▼ Ö < Menu > Ö [ ENTER ] Ö ▼ Ö < Device > Ö ►▼ Ö < Remote Device > Ö [ ENTER ] Ö ▲▼◄► Ö [ ENTER ] • Remote control: Select whether to use a remote control. • ID: Sele...
Page 69 - SETTING THE RECORDING; Recording Schedule
SETTING THE RECORDING You can setup scheduled recording, event recording and other recording related settings. Recording Schedule Make your reservation on a date and time to schedule the recording on specified time. [ MENU ] Ö [ ENTER ] Ö ▼ Ö < Menu > Ö [ ENTER ] Ö ▼ Ö < Record > Ö ► Ö &...
Page 70 - Record Setting
Record Setting You can set resolution, IPS, and quality of recordings by channel, and by recording type of standard / event. You can check frame rates and data transfer amount of Full Frame and Key Frame recordings for each channel, and set the transfer limit for recordings. [ MENU ] Ö [ ENTER ] Ö ▼...
Page 71 - Setting the camera recording profile
Setting the camera recording profile You can set the video profile to perform recording on your camera connected to each channel. [ MENU ] Ö [ ENTER ] Ö ▼ Ö < Menu > Ö [ ENTER ] Ö ▼ Ö < Record > Ö ►▼ Ö < Record Setup > Ö [ ENTER ] Ö ▼► Ö < Camera > Ö [ ENTER ] Ö ▲▼◄► Ö [ ENTE...
Page 72 - Record Option
Record Option When the HDD capacity is full, you can set whether to stop recording or start overwriting. [ MENU ] Ö [ ENTER ] Ö ▼ Ö < Menu > Ö [ ENTER ] Ö ▼ Ö < Record > Ö ►▼ Ö < Record Option > Ö [ ENTER ] Ö ▲▼◄► Ö [ ENTER ] • Disk End Mode : Select a HDD repetitive recording type...
Page 73 - SETTING THE EVENT; Sensor Detection
SETTING THE EVENT You can make the setup for record in case of sensor detection, camera event or video loss detection. Sensor Detection You can set the sensor's operating condition and connected camera, as well as alarm output and its duration. [ MENU ] Ö [ ENTER ] Ö ▼ Ö < Menu > Ö [ ENTER ] Ö...
Page 74 - Camera Event
Camera Event You can specify operation of events sent from your camera (motion detection, video analysis events, audio events), alarm display methods, and alarm time. [ MENU ] Ö [ ENTER ] Ö ▼ Ö < Menu > Ö [ ENTER ] Ö ▼ Ö < Event > Ö ►▼ Ö < Camera Event > Ö [ ENTER ] Ö ▲▼◄► Ö [ ENTE...
Page 75 - Video Loss Detection; Alarm Out Schedule
Video Loss Detection You can set the camera so that the camera can trigger the alarm if it is disconnected or the video is lost due to unstable network connection. [ MENU ] Ö [ ENTER ] Ö ▼ Ö < Menu > Ö [ ENTER ] Ö ▼ Ö < Event > Ö ►▼ Ö < Video Loss Detection > Ö [ ENTER ] Ö ▲▼◄► Ö [...
Page 76 - NETWORK CONFIGURATION; Interface; Setting a network connection
NETWORK CONFIGURATION It provides networked monitoring of Live screen from a remote place, and supports mail forwarding function with events. You can configure the network environment which enables such functions. Interface You can set the network connection route and protocol. Setting a network con...
Page 77 - Connecting and Setting the Network; When no router is used
Connecting and Setting the Network Networking may differ from the connection method, check your environment before setting the connection mode. When no router is used • Static IP mode - Internet connection : Static IP, leased line, and LAN environments allows connection between the NVR and remote us...
Page 79 - Port Setting
Port Setting [ MENU ] Ö [ ENTER ] Ö ▼ Ö < Menu > Ö [ ENTER ] Ö ▼ Ö < Network > Ö ► Ö < Interface > Ö [ ENTER ] Ö ▼► Ö < Port > Ö [ ENTER ] Ö ▲▼◄► Ö [ ENTER ] • Protocol Type : Select the protocol type among TCP, UDP - Unicast and UDP - Multicast. • Device Port : Enter the con...
Page 80 - DDNS
DDNS If a remote user accesses the network, you can set whether or not to use DDNS and the site to be connected. [ MENU ] Ö [ ENTER ] Ö ▼ Ö < Menu > Ö [ ENTER ] Ö ▼ Ö < Network > Ö ►▼ Ö < DDNS > Ö [ ENTER ] Ö ▼ Ö < Network 2 > Ö ▲▼◄► Ö [ ENTER ] • DDNS Site : Specify the use ...
Page 81 - DDNS Setting; IP Filtering
DDNS Setting DDNS is a short form of Dynamic Domain Naming System.DNS (Domain Name System) is a service that routes a domain name consisting of user friendly characters (ex : www.google.com) to an IP address consisting of numbers (64.233.189.104).DDNS (Dynamic DNS) is a service that registers a doma...
Page 82 - SSL
SSL You can select a security connection system or install public certificates. [ MENU ] Ö [ ENTER ] Ö ▼ Ö < Menu > Ö [ ENTER ] Ö ▼ Ö < Network > Ö ►▼ Ö < SSL > Ö [ ENTER ] Ö ▲▼◄► Ö [ ENTER ] • Secured Connection System : You can select a type of security connection system. - HTTP ...
Page 83 - Live Streaming Setting
• ID : Enter the ID provided by the RADIUS server administrator. ` If the entered ID does not match the ID of the client's certificate, it won't be processed properly. • Password : Enter the password provided by the RADIUS server administrator. ` If the password you entered does not match that of th...
Page 84 - SMTP Setting
E-mail You can send an e-mail to a NVR-registered user at a specific time interval, or if an event occurs. M ` If the camera is set to < OFF > or the channel's event is Video Loss, a notification is sent to the designated email address only in text. SMTP Setting Sets the SMTP mail server. [ ME...
Page 85 - Event Setting; Recipient Setting
Event Setting You can set the interval and type of the event that will be sent to the user. [ MENU ] Ö [ ENTER ] Ö ▼ Ö < Menu > Ö [ ENTER ] Ö ▼ Ö < Network > Ö ►▼ Ö < E-mail > Ö [ ENTER ] Ö ▼► Ö < Event > Ö [ ENTER ] Ö ▲▼◄► Ö [ ENTER ] • Event Interval : Set the event interva...
Page 86 - SNMP
SNMP Using the SNMP protocol, the system or network administrator can monitor the network devices remotely as well as the operating environment. [ MENU ] Ö [ ENTER ] Ö ▼ Ö < Menu > Ö [ ENTER ] Ö ▼ Ö < Network > Ö ►▼ Ö < SNMP > Ö [ ENTER ] Ö ▲▼◄► Ö [ ENTER ] • Enable SNMP v1 : SNMP ...
Page 87 - DHCP Server; Network Setting; Check IP
DHCP Server You can set the internal DHCP server and assign an IP address to the network camera. [ MENU ] Ö [ ENTER ] Ö ▼ Ö < Menu > Ö [ ENTER ] Ö ▼ Ö < Network > Ö ►▼ Ö < DHCP Server > Ö [ ENTER ] Ö ▼ Ö < Network > Ö ▲▼◄► Ö [ ENTER ] Network Setting • Network 1 : Select <...
Page 88 - SEARCH; Time Search
SEARCH You can perform the search for recorded data by the time or by the search criteria such as an event.You can access the < Search > menu directly in Live mode. 1. In live mode, right click with the mouse button or press the [ MENU ] button on your remote control. The Live menu appears. 2....
Page 89 - Color indications depending on current recording status; Event Search
3. The record data on the specific date will be listed.The display bar is different according to the data type. So check the data type for the color in the left pane. M ` If DST (Daylight Saving Time) is configured, overlapping multiple recordings may be produced for a certain moment of time. Such a...
Page 91 - PLAYBACK
PLAYBACK Play You can play data stored in the HDD and backup a desired portion of the data. 1. In the live menu screen, select < Play > menu or click on < > in the launcher menu or press the [ + ] button on your remote control. 2. Using the up/down(▲▼) button, select the search menu. ` I...
Page 92 - Using the Playback Button
Using the Playback Button Name Description Play Timeline Indicates the current playback point, and can be used to move. b Skip Backward Moves backward by unit time. c Backward Fast Play Used for quick backward search while in Play. Backward Slow Play Used for backward frame-by-frame search while in ...
Page 93 - Product Features; System Requirements; starting web viewer
WHAT IS WEB VIEWER? WebViewer is a software program with which the operator can access a remote NVR (Network Video Recorder) for real-time monitoring, PTZ control (if configured) or search. Product Features • Remote connection using the browser • PTZ camera control enabled • Supports 1, 4 camera vie...
Page 94 - CONNECTING WEB VIEWER
CONNECTING WEB VIEWER 1. Open your web browser and type the IP address or URL of NVR into the URL address box. M ` You need to connect network 2 before you can access the web viewer. ` " 192.168.2.200 " is set to IP by default. ` You must have specified the IP address in " Network > I...
Page 95 - If you want to access the web viewer with multiple browsers
4. When a program installation wizard window appears, press the [ Install ] button to install the program. ` The version of the program installed may vary depending on the update version. 5. When program installation is complete, click on the [ Finish ] button. 6. When installation is finished, and ...
Page 96 - LIVE VIEWER; Live Viewer Screen; live viewer
LIVE VIEWER You can check the video from camera registered in the NVR connected from a remote PC. Also, you can adjust the camera and check the network transfer status. Live Viewer Screen Menu Description System Stauts Indicator Displays icons to display the screen or system status. b Menu Selection...
Page 98 - System Status
LIVE SCREEN CONFIGURATION System Status You can check the status or operation of the NVR with the icons on the live screen. Item Description System Operation It is displayed when there is a problem with the fan. Displayed if the HDD is full and the NVR has an insufficient space torecord. Displayed i...
Page 99 - To capture a screen; To print a screen; Saving layout
To capture a screen 1. Click < > button. When a pop-up window appears, select the saving path for captured image. 2. Select the path and name the file. And then click the [ OK ] button. 3. Save current camera's video image as .bmp, .jpg or .png file. J ` If the viewer is running without the ad...
Page 100 - Changing Split Mode
Changing Split Mode If you want to maintain the current screen ratio When you change from a split screen, check < Keep Aspect ratio > to maintain the ratio and change to a different size. To go to your desired channel screen Press the < > button to move to the previous/next channel group...
Page 101 - Setting screen switching; To perform switching
Setting screen switching If you don't register the layout, the screen switching function will not operate. You can view the layouts one by one. Click on the < > button to launch the switching setting window. 1. Enter the desired screen switching time. 2. Click on the < OK > button to sav...
Page 103 - CONTROLLING A CONNECTED NETWORK CAMERA; Controlling PTZ
CONTROLLING A CONNECTED NETWORK CAMERA Controlling PTZ If PTZ camera is connected, the < > icon appears on screen. When selecting corresponding camera channel, the PTZ tab is provided to allow you to control the PTZ. Item Description Camera menu Displays the camera settings menu. b Direction A...
Page 104 - To set a preset; To activate the preset
Item Description Group Moves in the path specified by combining the preset. Trace Moves camera's framing in the predefined path. Tour Moves in the path specified by combining multiple groups. Focus Adjusts the focus of the camera. Zoom Zooms in/out the image by controling camera's zoom. m Sensitivit...
Page 105 - SEARCH VIEWER; Search Viewer Screen; search viewer
SEARCH VIEWER You can search and play the video record saved in NVR by accessing NVR remotely. Search Viewer Screen Item Description Menu Selection Switches to the corresponding menu screen by clicking each menu. b Calendar Displays the video-recorded date in blue and today in red. Click the date in...
Page 106 - To search by date
Item Description Sound Change the PC volume between 0 and 100. Capture Saves current video for selected channel in the designated path. Print Prints current video image for selected channel through the assigned printer. Section backup Backup the video for the selected section. Magnify/Shrink Magnify...
Page 108 - Names and Functions of Play Buttons
Names and Functions of Play Buttons Item Description Back Returns to the previous event. b Previous frame Move backward one sec. c Backward X times speed playing Used to rewind at X times the speed. Stop After finishing playing, move to the live mode. Play/Pause Video is played and paused. Forward X...
Page 109 - setup viewer; SETUP VIEWER; Settings Screen
setup viewer SETUP VIEWER You can configure the NVR settings remotely on the network. To configure the NVR settings, click < Setup >. Settings Screen Item Description Menu Selection Click each menu to switch into corresponding menu screen. b Parent Menu Configure the settings or select a paren...
Page 110 - System
System You can configure the various settings of the NVR system. Date/Time/Language For more information, refer to " Date/Time/Language " in the " System " menu. (Page 41) Date/Time Set the date and time. Time Synchronization Setup Set the time synchronization. DST (Daylight Saving T...
Page 111 - Permission Management
Permission Management For more information, refer to " User " in the " System Setup " menu. (Page 43) Admin You can change the admin ID or the password. ID allows alphanumeric characters only. ` If the admin ID is not used for access, you cannot change the ID. ` If the ID being use...
Page 112 - Log information
System Management For more information, refer to " System Management " in the " System " menu. (Page 47) System Information You can see information of the current system.Check the software version and MAC address. Settings Using a storage device, you can apply the current configurati...
Page 117 - Record
Record For more information, refer to " Setting the Recording ". (Page 69) Recording Schedule If you set a recording schedule for a specific date and time, the recording will start at that specific time. Record Setup NVR Select a type of the normal/event recording frame rate for each channel...
Page 119 - Event
Event For more information, refer to " Setting the Event ". (Page 73) Sensor Detection NVR / Camera You can set the sensor operation mode and the synchronized camera as well as the alarm output type and the duration. ` If the connected network camera that has configured the alarm in/out sett...
Page 122 - Live Streaming
802.1x When connecting to a network, you can select whether to use the 802.1x protocol and install corresponding certificate. Live Streaming You can configure the network transfer settings of the network camera. E-mail You can specify the SMTP server that sends a mail if an event occurs and set the ...
Page 125 - Using the setting icons
Using the setting icons • : Display the ID of user connected. • : You can register a network camera for each channel and easily set the resolution and the number of shots in case of event occurrence or manaual recording. ` For more on how to register a camera, refer to " To register a camera ...
Page 127 - SEC BACKUP VIEWER; Recommended System Requirements; backup viewer
SEC BACKUP VIEWER You can play a file that is backed up in the format of SEC. Backup in SEC format produces backup data file, library file and self-executable viewer file. If you run the backup file viewer, the backup data file will be played. Recommended System Requirements PCs with a lower specifi...
Page 129 - PRODUCT SPECIFICATION; appendix
PRODUCT SPECIFICATION Item Details Display Network Camera Inputs Max. 4CH Resolution CIF ~ 5MP Protocols Samsung(SVNP), ONVIF supporting version(1.0 ~ 2.22) Live Local Display HDMI/VGA Multi-Channel Display [Local Monitor] 1 / 4 / Auto Sequence[Web] 1 / 4 / Auto Sequence Performance [Local Monitor] ...
Page 134 - PRODUCT OVERVIEW
PRODUCT OVERVIEW unit : mm (inches) 320 [12.6] 323.9 [12.75] 370 [14.57] 44 [1.73] 50.7 [2] 134_ appendix appendix
Page 135 - DEFAULT SETTING
DEFAULT SETTING To reset the system, move to " System Management > Settings > Load Factory Default " and press the < Initialization > button. This returns the factory default settings. M ` When you initialize the system without changing the < Authority Setting >, you must e...
Page 138 - TROUBLESHOOTING
TROUBLESHOOTING Problem Action The system does not turn on and the indicator on the front panel does not work at all. y Check if the power supply system is properly connected. y Check the system for the input voltage from the power source. y If the problem persists even after you have taken the abov...
Page 142 - OPEN SOURCE LICENSE REPORT ON THE PRODUCT; GNU GENERAL PUBLIC LICENSE
OPEN SOURCE LICENSE REPORT ON THE PRODUCT The software included in this product contains copyrighted software that is licensed under the GPL/LGPL. You may obtain the complete Corresponding Source code from us for a period of three years after our last shipment of this product by sending email to hel...
Page 143 - NO WARRANTY
c) If the modified program normally reads commands interactively when run, you must cause it, when started running for such interactive use in the most ordinary way, to print or display an announcement including an appropriate copyright notice and a notice that there is no warranty (or else, saying ...
Page 144 - END OF TERMS AND CONDITIONS; GNU LESSER GENERAL PUBLIC LICENSE
LOSS OF DATA OR DATA BEING RENDERED INACCURATE OR LOSSES SUSTAINED BY YOU OR THIRD PARTIES OR A FAILURE OF THE PROGRAM TO OPERATE WITH ANY OTHER PROGRAMS), EVEN IF SUCH HOLDER OR OTHER PARTY HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES. END OF TERMS AND CONDITIONS How to Apply These Terms to ...
Page 151 - PCRE LICENCE
To do so, attach the following notices to the program. It is safest to attach them to the start of each source file to most effectively state the exclusion of warranty; and each file should have at least the "copyright" line and a pointer to where the full notice is found. <one line to gi...
Page 152 - OpenSSL License
- Redistributions of source code must retain the above copyright notice, this list of conditions and the following disclaimer. - Redistributions in binary form must reproduce the above copyright notice, this list of conditions and the following disclaimer in the documentation and/or other materials ...
Page 158 - SALES NETWORK
SALES NETWORK SAMSUNG TECHWIN CO., LTD. Samsung Techwin R&D Center, 6, Pangyo-ro 319beon-gil, Bundang-gu, Songnam-si, Gyeonggi-do 463-400, KoreaTEL : +82-70-7147-8740~60 FAX : +82-31-8018-3745 SAMSUNG TECHWIN AMERICA Inc. 100 Challenger Rd. Suite 700 Ridgefield Park, NJ 07660 Toll Free : +1-877-...
