Page 2 - IMPORTANT SAFETY INSTRUCTIONS
Eng-2 IMPORTANT SAFETY INSTRUCTIONS 1. Read these instructions. 2. Keep these Instructions. 3. Heed all warnings. 4. Follow all instructions. 5. Do not use this apparatus near water. 6. Clean only with dry cloth. 7. Do not block any ventilation openings. Install in accordance with the manufacturer’s...
Page 3 - CAUTION : TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT
Graphic Symbol Explanation The lightning flash with arrowhead symbol within an equilateral triangle is intended to alert the user to the presence of uninsulated ‘dangerous voltage’ within the product’s enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons. T...
Page 4 - IMPORTANT SAFEGUARDS; Caution
Eng-4 IMPORTANT SAFEGUARDS Caution Power source is indicated on the rear of the set. It contains high-voltage parts. If you remove the cover, it may cause fire or electric shock. Do not remove thecover by yourself. (Control switches are at the front of the monitor.) 1. Read Instructions : All the sa...
Page 7 - FCC & ICES Information; Warning
Eng-7 18. Replacement Parts : When replacement parts are required be sure the service technician has used replacement parts specified by Samsung or have the same characteristics as the original parts. Unauthorized substitutions may result in fire electric shock or other hazards. 19. Safety Check : U...
Page 8 - Information to user; the following two conditions: (1) this device may not cause harmful
Information to user Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. NOTE: This equipment has been tested and found to comply with the limits for a Class A digital device pursuant to Part 15 of the FCC R...
Page 9 - IC Compliance Notice
Eng-9 The party responsible for product compliance: SAMSUNG ELECTRONICS CO., LTD. America QA Lab of Samsung 3351 Michelson Drive, Suite #290, Irvine, CA92612 USA IC Compliance Notice This Class (A) digital apparatus meets all requirements of the Canadian Interference-Causing Equipment Regulations. C...
Page 10 - Contents; Chapter 1: System Components and Installation; STANDARD; CAMERA composition; Chapter 2: MONITOR FRONT PANEL KEY Function and
Eng-10 Contents IMPORTANT SAFETY INSTRUCTIONS .................................. 2 IMPORTANT SAFEGUARDS ..................................................... 4 FCC & ICES Information .............................................................. 7 Chapter 1: System Components and Installation 1-...
Page 12 - -1) Environmental requirements for installation and safety; malfunction and reduce system downs due to environmental causes.
Eng-12 Chapter 1: System Components and Installation 1-1) Environmental requirements for installation and safety This section describes the environmental requirements for safe installation and use. Install the product on a flat table or in a rack. It should be used only when level and should not be ...
Page 14 - composition and installation method; c. Camera fitting groove; the camera if necessary.
Eng-14 1-3) STANDARD CAMERA composition and installation method 1) Standard Camera composition (SOC-C120) a. Lens It has a focal length of 3.8mm and makes it possible for you to observe a relatively wide area. b. Microphone Capable of picking up all sound in the vicinity of the camera location and t...
Page 15 - It outputs the sound signal which was transfered from the monitor.
Eng-15 f. Speaker It outputs the sound signal which was transfered from the monitor. 2) INSTALLING STANDARD CAMERA (SOC-C120) SOC-C120 camera can be attached to the wall, ceiling or shelf using the camera mount bracket (SBR-110S). Choose an installation site that can sufficiently support the weight ...
Page 16 - Operating Temperature :; onto the CAMERA MOUNT BRACKET.
Eng-16 3) CAMERA MOUNT BRACKET(SBR-110) & STANDARD CAMERA(SOC-C120) (1) Overview CAMERA MOUNT BRACKET (SBR-110S) is used to attach the camera to a wall, ceiling or shelf. (2) Specifications Use : Indoor Installation : Wall or Ceiling Dimensions : 57 (W) X 47.2(H) X 100.5(L) Weight : 150g Operati...
Page 18 - Connection status checking method :; The initial screen mode of monitor is quad mode.
Eng-18 After positioning monitor and installing four cameras to a desired location, please connect CAMERA to MONITOR through CAMERA CABLE (MCB-60) as shown in the below figure. Please check whether or not it is properly connected. Connection status checking method : • Turn on the monitor after conne...
Page 19 - NIGHT VISION CAMERA; ) Before Installation; used not only indoors, but also outdoors.; ) Precautions for Installation and Operation; * Install SOC-N120 in a cool place where there is no direct sunlight.
Eng-19 1-4) NIGHT VISION CAMERA 1) Before Installation SOC-N120 INTRODUCTION SOC-N120 Nightvision camera is intended to be used exclusively with those sold by this company for DIY. With the built-in IR LED and light sensor in the camera, both day monitoring and night monitoring are possible. Also, s...
Page 20 - SOC-N120 Pin Configuration
Eng-20 3) Installation 1. Make sure the installation location is a place where 5 times (about 2.2lbs) of the total weight of the camera can be tolerated before installing the camera. 2. Connect the cable below the camera after attaching the provided Mount Bracket to the desired place. 3. Use the han...
Page 21 - ) Nom des composantes; - Detects incoming light to control the IR LED.
Eng-21 4) Nom des composantes a). Lens - It has a focal length of 3.8mm and makes it possiblefor you to observe a relatively wide area. b). Illumination Sensor - Detects incoming light to control the IR LED. c). IR LED - This is an infrared LED that is controlled by the illumination sensor. d). Came...
Page 22 - ) External terminal connecting method for CAMERA
Eng-22 Eng-22 1-5) External terminal connecting method for CAMERA and MONITOR 1) External terminal connecting method for CAMERA • An additional PIR sensor or external sensor can also be connected. • The additional PIR sensor can be connected as shown in the above graphic. • Sensor’s trigger signal i...
Page 23 - -6) Whole System connection and configuration
Eng-23 Eng-23 f) Not Used g) Connect the A/O (HOT) terminal on the rear panel to the Alarm IN terminal of the VCR. h) Connect the A/O (COLD) terminal on the rear panel to the Ground terminal of the VCR. i) Connect the A/R terminal on the rear panel to the Alarm Reset terminal of the VCR. j) Connect ...
Page 24 - Total System Configuration
Page 25 - Local System Configuration; Local PC to use during setup.
Eng-25 Local System Configuration 1. Connect LAN cable of Cable/ADSL modem or Direct Fixed/Static IP LAN Line to WAN port of IP Router. 2. Connect LAN ports of IP Router(1~4 or 1~8) to Ethernet port SMO-151QN to be set up and to Ethernet port of Local PC to use during setup. 3. Connect Video cable o...
Page 26 - Front Panel; key on the; KEY
Eng-26 Eng-26 Chapter 2: MONITOR FRONT PANEL KEY Function and Using Method Front Panel 2-1) TALK KEY TALK KEY allows users to transmit voice signal to intended camera by inputting voice with built-in MIC in the front of the monitor. For this function, select a target camera with the ▲ / ▼ key on the...
Page 28 - ENTER
Eng-28 Eng-28 Eng-28 2-8) PIP- KEY Can be used to see the main screen while Single screen is displayed. The main screen can be changed and transfered to another channel while PIP is working. Please refer to "CHAPTER 4. DISPLAY MODE setting method(Eng-86)" for PIP function and details. 2-9) F...
Page 30 - -1) ADJUST MENU function and setting method
Eng-30 Eng-30 Chapter 3: Setting each item function at SETUP MENU Pressing the MENU BUTTON of the FRONT PANEL allows users to enter SETUP MENU and see the following menu OSD box. Setting method of each SETUP MENU function and operation is as follows. 3-1) ADJUST MENU function and setting method • Fu...
Page 35 - -7) NETWORK SETTING function and setting method; Static IP User; - Constituted by Static IP on the TCP/IP network; • Static
Eng-35 Eng-35 3-7) NETWORK SETTING function and setting method • Function: Allows users to select the STATIC (fixed) IP, DHCP, PPPoE of Setting. • Setting method: Move to #7, NETWORK SETUP MENU by using ▲ / ▼ KEY at SETUP MENU, then press the ENTER SWITCH to display the OSD as shown in the figure be...
Page 36 - CAUTION; A port number is reserved for TCP port and HTTP port setting.; IP Address of the Router and the HTTP port assigned to the SMO-151QN.
Eng-36 Eng-36 5) After setting, move to the main screen by using the MENU BOTTOM. 6) Set values will be stored shown below. It takes 2 or 3 seconds. On completion of setting to Static IP(Fixed IP)setup, the screen, [S] is displayed. If the network connection is cancelled or cut, [S] starts blinking....
Page 37 - DHCP User; - Constituted by Dynamic IP on the cable/xDSL modem network; DDNS to support the Dynamic IP.
DHCP User - Constituted by Dynamic IP on the cable/xDSL modem network You can use the SMO-151QN products through the network using Dynamic IP on cable/xDSL modem. In this case, it should be connected with DDNS to support the Dynamic IP. In case of a configuration using DHCP, as the connection to SMO...
Page 39 - At this time, you should add “s” in front of “mac address”.
Eng-39 8) Open your Internet Explorer web browser, type in the following in the URL window and press Enter. http://sff0000.websamsung.net Where ff0000 is the MAC address of your SMO-151QN in this example. If your SMO-151QN’s MAC address is ff0001, then type in ff0001 instead of ff0000 * Note : MAC A...
Page 40 - ) MOVE TO EACH item by using
Eng-40 ADSL User (PPPoE) - Constituted by IP on PPPoE (ADSL) SMO-151QN products can be used on the network using IP through PPPoE (ADSL). In case of a configuration using PPPoE, SMO-151QN connection is made through the domain names (EX : http://sff0000.websamsung.net) that are automatically register...
Page 41 - Password, you can not see the image transferred from SMO-151QN.; ID and PASSWORD can be inputted to 40 characters in the maximum.
Eng-41 4) When the PPPoE (ADSL) type in the User Name and Password (and Confirm Password) given to you by the ADSL Service Provider. CAUTION In case of using ADSL (ISP-internet service provider) you must type correct User Name and Password by ISP to connect to SMO-151QN. If you type incorrect User N...
Page 43 - nications, please reboot by turning off the power of ADSL Modem and; “Active X controls and plug-ins to run” screen.
Eng-43 CAUTION The connection to SMO-151QN is unavailable for about 2~5 minutes after ADSL Modem’s power ON. Since the connection would not be available, as IP is not received from ADSL commu- nications, please reboot by turning off the power of ADSL Modem and SMO-151QN for more than 5 seconds and t...
Page 45 - - Remote Viewer Function Buttons
KEY Type Function Choose a camera by channel Ch 1 ~ Ch 8 CHANNEL NEXT SINGLE MODE (ch1 Default selected) 320 X 240 Size 720 X 480 QUAD MODE (QUAD Default selected) SEQUENCE MODE SAVE CAPTURE REC Eng-45 3-8-1) “LIVE” MENU - CAMERA SELECT Initial display mode of monitor if QUAD A. - Remote Viewer Func...
Page 46 - - SINGLE SCREEN DISPLAY
Eng-46 PLAY STOP LIVE MODE change ADMIN MODE change - SINGLE SCREEN DISPLAY In case users want to see the camera image at full mode, Select a target camera by turning camera select key. After camera selection, camera image will be displayed at full screen. * AT SINGLE DISPLAY - QUAD MODE DISPLAY A u...
Page 50 - Player will be installed together when it is connected to
Eng-50 3. PLAYER - Player installation/execution/deletion - Installation Player will be installed together when it is connected to SMO-151QN. - Execution (Follow the instruction to execute it separately.) Click Start Program —> SSC WEB Control —> Player. (Fig. 3) FIG.3 - Deletion Click Start —...
Page 51 - - Program screen configuration
Eng-51 - Program screen configuration - How to play 1. Playback File - Open... Selecting this, you can choose one between fjp and jpg on a window as shown below.
Page 53 - Type in the file name and press ‘Save’ to store it as a jpeg file.
Eng-53 - Snap shot It is a function to save the present image as a form of a jpeg file. Select in the toolbar. The result will be as follows. Type in the file name and press ‘Save’ to store it as a jpeg file. - Print It is a function to print the present image. Select in the toolbar. The result will...
Page 54 - Select Print and press ‘OK’.
Eng-54 Type in the phrase you added in ‘Description’. Then press the ‘OK’ button. Select Print and press ‘OK’.
Page 55 - Admin Menu; To use this menu, you need the administrator’s ID and Password.; Admin Menu Entering; ) Click the Admin menu and a login window will appear.
Eng-55 Admin Menu It is an administrator’s menu to set the general items on SMO-151QN Server. To use this menu, you need the administrator’s ID and Password. On delivery, they are “root” (administrator’s ID) / “root” (administrator’s Password). The password can be changed on Admin Menu. Admin Menu E...
Page 57 - Admin Menu Structure; Category
Eng-57 • Admin Menu Structure Category Main Menu System Configuration System Information Admin. Password Access Limitation User Registration Video Alarm Notification Network Configuration Network Configuration PPPoE (ADSL) Network Ports View Network Status Network Status Notification DDNS Configurat...
Page 58 - System Information
Eng-58 3-8-2) System Configuration Menu. 1. System Information In this menu, you can check the information on the system including the name of the SMO-151QN Server. Server name can be changed as a user wants. - Menu Configuration After completing setting, click Apply button. If you click the back bu...
Page 59 - root
Eng-59 2. Admin Password In this menu, the password of the administrator (root) can be changed. - Menu Configuration After completing setting, click Apply button. If you click the back button, initial values are typed in all fields.. After clicking the apply button, the new password will be applied....
Page 60 - Access Configuration
Eng-60 3. Access Configuration This menu is to set the targets the SMO-151QN Server can have an access to. - Menu Configuration After completing setting, click Apply button. If you click the back button, initial values are typed in all fields. Access Limitation This is to limit the maximum frame spe...
Page 63 - After completing setting, click Apply button.
Eng-63 5. Video Configuration This is to set the data to be added in the video data and set an environment for each channel. - Menu Configuration After completing setting, click Apply button. If you click the default button, initial values are typed in all fields. Image Size This is to choose the si...
Page 65 - image transfer in your mail account.
Eng-65 EX) When user who has an e-mail address ([email protected]) and password(123456) in YAHOO sets “Alarm Notification” in order to send a mail to [email protected]... After completing setting, click Apply button. If you click the back button, initial values are typed in all fields. In the event of ...
Page 66 - Network Configuration
Eng-66 3-8-3) Network Configuration Menu. 1. Network Configuration On this menu, you can fix the general environment related to the network of the SMO-151QN Server and check the present status of it. - Menu Configuration 1) Fix the IP address of the SMO-151QN Server, NetMask, GateWay, DNS1, DNS2, et...
Page 67 - ) Type in the addresses of DNS 1 and DNS 2.
Eng-67 1-1. Network Configuration : Static IP / DHCP Client 1) If the IP of the SMO-151QN Server is Static : Choose “Static IP”. 2) Type in the IP Address you want to assign to the SMO-151QN Server, NetMask, GateWay, DNS1, and DNS2 addresses. 1-2. Network Configuration : Static IP / DHCP Client 1) I...
Page 68 - At this time, you should add “s” in front of “MAC address”.
Eng-68 3) Click Apply button to apply the settings. If you click Reset button, the latest setting will be applied again. Click Back button if you don’t want to apply the setting. 4) If the mac address of an user is XX:XX:XX:FF:00:00, an user who uses DDNS but do not know IP can connect the Viewer by...
Page 70 - Network Ports Configuration; ) The fault values is 80 and it can be assigned up to 65535 maximum.; where firewall constitutes or a particular port Etc.
Eng-70 3. Network Ports Configuration It sets the HTTP Port number to use when the SMO-151QN Server communicates with a Client PC. The present SMO-151QN Server uses HTTP Port (80). - HTTP Port 1) This is the port the Client PC uses to connect to the web page of the SMO-151QN Server. Depending on the...
Page 73 - delivers it to the receiver.
Eng-73 Network Status Notify Configuration click “Network Status Notify” in the Network Configuration group. Choose to use the Mail Notification function or not. Choose “Enable” if you want to notify the network status of the SMO-151QN Server to the people who want through e-mails. Type the address ...
Page 77 - Save Configuration; This menu is to save all of the present setting in the Flash Memory.
Eng-77 1. Save Configuration This menu is to save all of the present setting in the Flash Memory. If you changed any of the setting for the SMO-151QN, it is recommended that you save it in the Flash Memory in this menu.
Page 80 - Click “Cancel” to stop updating.
Eng-80 3-2. All (kernel, RAM disk, System, Web) Update When you click the start button located, a window will appear to ask if you want to update. Click “Cancel” to stop updating. 1. “OK” to proceed updating. 2. A pop-up window will appear. Choose “Zimage” in the browse.
Page 81 - Click “Next” button to move to the next stage.
Eng-81 3. Click “Next” button to move to the next stage. Click “Skip” button to move to the next stage without Kernel Image’s update. Click “Next” button and a window will appear to check the name and size of the file.
Page 84 - Click “Next” button to move to the next stage.
Eng-84 6. In the next stage, a pop-up window will appear for the file searching process for the System Image Update. Choose “Fw_2pq.tar.gz” in the browse. 7. Click “Next” button to move to the next stage.
Page 88 - -9) VIEW EVENT LOG MENU function and setting method; Displays the time and date of camera event and type of event.; the next page by using; SWITCH. A Total of 64 events can be listed.
Eng-88 06/01/03 13:14:00 NO CH MM/DD/YY HH:MM:SS EVT 01 07 02/10/03 10:00:30 A 02 01 02/11/03 11:22:00 L 03 01 06/01/03 12:33:01 - 04 02 06/01/03 13:01:03 - 05 01 --/--/-- --:--:-- - 06 01 --/--/-- --:--:-- - 07 01 --/--/-- --:--:-- - 08 01 --/--/-- --:--:-- - 3-9) VIEW EVENT LOG MENU function and s...
Page 89 - Chapter 4: DISPLAY MODE setting method; full mode, select a target camera by using
Eng-89 Chapter 4: DISPLAY MODE setting method 4-1) SINGLE SCREEN DISPLAY Initial display mode of monitor is QUAD A. In case users want to see the camera image at full mode, select a target camera by using ▲ / ▼ KEY. After that, press the ENTER SWITCH and selected camera image will be displayed at fu...
Page 90 - * At QUAD MODE display from SINGLE MODE or SEQUENCE MODE,
Eng-90 4-2) QUAD MODE DISPLAY Users can switch SINGLE DISPLAY MODE and SEQUENTIAL DISPLAY MODE to QUAD DISPLAY MODE, or QUAD - A (QUAD - B) to QUAD - B (QUAD - A), or PIP MODE to QUAD MODE, press the QUAD/PAGE KEY. * At QUAD MODE display from SINGLE MODE or SEQUENCE MODE, CH3 CH3 DISPLAY QUAD MODE D...
Page 92 - on PIP screen ,the main screen will change. If you press the; and
Eng-92 4-4) PIP MODE DISPLAY Can be used to see PIP screen in Single screen mode. If you press the ENTER on PIP screen ,the main screen will change. If you press the ▲ / ▼ KEY,the main screen can be transferred to another channel. Sub-screen location can be selected on DISPLAY MENU in SETUP MENU. CH...
Page 94 - Chapter 5 : Each product feature; Product Specification
Chapter 5 : Each product feature Product Specification SOC-C120 : Standard Camera Eng-94 Model Name Broadcasting System Imaging Device Effective Pixels S Synchronization Resolution Signal Output S/N Ratio Minimum Scene Illumination Gamma Correction Lens Auto Exposure Audio I/O Connectors Operating T...
Page 96 - OBSERVATION MONITOR
Eng-96 Video Input Video Output Audio Input Audio Output Alarm/Motion Features: Connected to Alarm Box/Camera Sequence Event List Display mode Horizontal Resolution Operation Temperature CRT Dimension (W x D x H (mm)) Weight Power consumption Video system Operation Humidity Range AC Input Ranges Aud...
Page 97 - NETWORK
Eng-97 NETWORK • 32bit Embedded Processor • Flash Memory : 8Mbytes • SDRAM : 32Mbytes • HTTP, TCP/IP, FTP, Telnet, ARP, PPP, DHCP, PPPoE • Compression Algorithm : Real-time M-JPEG • Rate : 30 fps for each channel • Quality : 3 levels • NTSC • NTSC, 352x240, 704x240 • Max 30 Frame Per Second (NTSC) •...
Page 98 - A unique MAC address is registered to this device.
Eng-98 The system performance may decrease if the computer has lower specification than the recom-mecdations, is not installed with the latest service pack, or has an illegally installed operationsystem(OS). A unique MAC address is registered to this device. If the administrator setting and monitori...
Page 99 - Appendix A) Software up data; The initial screen of Samsung Electronics’ web site is as follows.
Eng-99 Appendix A) Software up data The initial screen of Samsung Electronics’ web site is as follows. 1. http://www.securitysamsung.com http://www.samsung.com/Products/CCTV.htm 2. Network Security in Homepage 3. Download the following items from SMO-151QN. ! Owner’s manual - SMO-151QN Owner’s manua...
Page 100 - Appendix B) IP Router Setup Guide; List of Routers compatible with SMO-151QN.; Total System Configuration; Other routers may be incompatible with SMO-151QN.
Eng-100 Appendix B) IP Router Setup Guide List of Routers compatible with SMO-151QN. Refer to Router User’s Manual for the detailed router setup. 1. Total System Configuration 2. Local System Configuration 3. Step-by-Step Examples : Linksys (Model : WRT54G) Netgear (Model : WGR614v4) D-Link (Model :...
Page 101 - Linksys model WRT54G
Eng-101 Step-by-Step Setup Example of IP Router Linksys model WRT54G 1. Click the “Application and Gaming” tab. 2. Click “Port Range Forward”. 3. Port forwarding Row #1 : Application : Set this to “HTTP” Start and End : Set both to “From 10000 to 65535” Protocol : Select “TCP” IP Address : SETUP MEN...
Page 105 - Printed in China
Part No.: AA68-03867E-00 Printed in China HEADQUARTERS105 Challenger RoadRidgefield Park, NJ 07660-0511TEL:1-800-SAMSUNGSERVICE DIVISION400 Valley Road,Suite 201Mount Arlington, NJ 078561-800-SAMSUNG(1-800-726-7864)www.samsung.com