Samsung SK-5A - Installation Manual
Samsung SK-5A – Installation Manual, read for free online in PDF format. We hope this helps you resolve any issues you may have. If you have further questions, please contact us through the contact form.
CAUTION
: Two people are required to lift the dryer on to
the washer.
WARNING
: These washer and dryer are not suitable for
mobile home or RV installation.
Dryer
STEP 1
Have two persons place the dryer on a non-slippery
floor. Then, have one person tilt the dryer to the side.
Do not lay the dryer down. The dryer may be scratched.
STEP 2-1 SKK-7*, SKK-8*:
Check if the legs are tightened up,
and then insert the stacking support guides in the
rectangular holes of the dryer’s base until you hear a
clicking sound. You don’t need to remove the legs.
STEP 2-2
SKK-BB:
Disassemble legs, and Snap the stacking
support guides into the rectangular holes in the dryer
base and secure each with two(2) screws Phillips-pan
head (6006-001174)
STEP 3
Repeat the same step above on the other side.
STEP 4
Bottom view of the dryer after assembling the Stacking
Support Guides to the dryer base.
* Use a stacking-kit compatible with the purchased model.
Washer (Stacking kit: SKK-7*, SKK-8*, for 27” models)
CAUTION
: You need to use the proper rear bracket
depending on your washer model. (There are 2 different
rear brackets : DC61-04160A, DC61-04955A)
5-1)
DC61-04160A : WF5*K**, WF4*H**, WF4*K**, WF4*M**,
WF4*N**, WF18H**, WF20H**, WF20M**, WF22H**,
WF22K**, WF15K**, WF16J65**
Left
Right
DO NOT TIGHTEN SCREWS COMPLETELY
STEP 5-1
LOOSELY assemble the Rear Brackets
(DC61-04160A) to the washer as shown below. Use
two (2) Screws-Hex Head (6002-001431) with washers
(DC60-00044A) in each washing machine Top Cover tail,
per bracket.
* Before installing the rear bracket, loosen two screws
(Screw-Hex) on the Cover Top that is secured to the frame.
5-2)
DC61-04955A : WF5*R**, WF4*R**, WF5*T**, WF4*T**,
WF2*R**, WF1*R**, WF2*T**, WF1*T**
Left
Right
DO NOT TIGHTEN SCREWS COMPLETELY
STEP 5-2
LOOSELY assemble the Rear Brackets (DC61-04955A)
to the washer as shown below. Use two (2) Screws-Hex
Head (6002-001431) with washers (DC60-00044A) in
each washing machine Top Cover tail, per bracket.
* Before installing the rear bracket, loosen two screws
(Screw-Hex) on the Cover Top that is secured to the frame.
Washer (Stacking kit: SKK-BB, for 30” models)
WF56H**
STEP 5-3
Loosely assemble the Rear Bracket (DC61-03846A) to
the washer as shown above in either case A or Case B,
Use (2) Screws-Hex Head (6009-001476) with washers
(DC60-00044A) to the each hole of Cover Top and Frame.
* Case A only : Before installing the rear bracket, loosen two screws
(Screw-Hex) on the Cover Top that is secured to the frame.
Case A
Case B
Small Cap
Big Cap
STACKING KIT INSTALLATION INSTRUCTIONS
(WASHER & DRYER ONLY)
DC68-01052R-11
StakingKit_DC68-01052R-11_EN.indd 1
2020-10-14 5:38:37
"Loading the manual" means you need to wait until the file loads and becomes available for online reading. Some manuals are very large, and the time they take to appear depends on your internet speed.
