Page 2 - IMPORTANT SAFETY NOTICE; WARNING; and plastic peripherals such as baskets and lids.
IMPORTANT SAFETY NOTICE Following the repair by a non-authorized service provider self-repair or non-professional repair of the product Samsung is not liable for any damage to the product any injury or any other product safety issue caused by any attempt to repair the product which does not carefull...
Page 3 - Tools For Removal And Reassembly _ 3; TOOLS FOR REMOVAL AND REASSEMBLY; Tool image; Preparation for parts replacement; Pull out the unit from the sink and lay it on the floor.
Tools For Removal And Reassembly _ 3 1. TOOLS FOR REMOVAL AND REASSEMBLY Tool image No. Tool Type Remarks ① Adjustable Wrench ② Open-end Wrench 1-7/16” ③ Vice Pliers ④ Others (screwdriver, nipper, long nose pliers) Common tools for servicing Screwdriver – Phillip, Flat, Torx T15 ⑤ Ear clamping tool ...
Page 4 - _ Standard Disassembly Drawings; STANDARD DISASSEMBLY DRAWINGS; Caution; - Make sure to remove all items include baskets inside dishwasher.
4 _ Standard Disassembly Drawings 2. STANDARD DISASSEMBLY DRAWINGS 2-1. PRECAUTION Caution Before servicing, - Make sure to remove all items include baskets inside dishwasher. - Drain the water in the dishwasher and disconnect the power supply. - Lock the water faucet that is connected with inlet ho...
Page 5 - Standard Disassembly Drawings _ 5; Part; CAP CASE; Warning; Be sure to remove the power plug before servicing.; NOTE
Standard Disassembly Drawings _ 5 2-2. CAP CASE BRAKE / GASKET BRAKE - Cap Case Brake : DD81-02725A / SVC-CAP CASE BRAKE- Gasket Brake : DD81-02726A / SVC-GASKET-BRAKE Part Figure Description CAP CASE BRAKE / GASKET BRAKE A B [DISASSEMBLY] 1. Remove 3 screws that connect left SIDE PANEL to front sid...
Page 6 - _ Standard Disassembly Drawings
6 _ Standard Disassembly Drawings Part Figure Description CAP CASE BRAKE / GASKET BRAKE 4. Take off the left SIDE PANEL. Warning Do not this work without safety gloves. It can cause injury from sharp edge. 5. Take off the CAP CASE BRAKE by rotating to counter-clockwise direction with long-nose plier...
Page 7 - Standard Disassembly Drawings _ 7; Remove 8 screws fixing the ASSY CONTROL
Standard Disassembly Drawings _ 7 2-3. DOOR HINGE - Door Hinge : DD82-01675A, DD82-01676A / SVC ASSY-HINGE-RIGHT, SVC ASSY-HINGE-LEFT Part Figure Description DOOR HINGE B A [DISASSEMBLY] PREPARATION: Remove SIDE PANEL Left & Right refer to the section of ‘CAP CASE BRAKE / GASKET BRAKE’. 1. Remov...
Page 8 - _ Standard Disassembly Drawings; Remove 2 terminals that connected to; Pay attention to hook of terminals.; Pay attention to DOOR drop after remove the rope.; Push both ribs of GUIDE HINGE to pull out the DOOR.; Do not this work without safety gloves. It can cause
8 _ Standard Disassembly Drawings Part Figure Description DOOR HINGE Hook Hook 4. Remove 2 terminals that connected to DETERGENT DISPENSER, and 1 ground wire that connected to BRACKET DOOR FRAME. Warning Be sure to remove the power plug before servicing. Caution Pay attention to hook of terminals. 5...
Page 9 - Standard Disassembly Drawings _ 9; DOOR INNER assembly to the direction of about 15 ̊.
Standard Disassembly Drawings _ 9 Part Figure Description DOOR HINGE About 15˚ 7. Do same work at the opposite side, and pull out the DOOR INNER assembly to the direction of about 15˚. Warning Do not this work without safety gloves. It can cause injury from sharp edge. 8. Remove 2 screws to take off...
Page 10 - 0 _ Standard Disassembly Drawings; Make sure the Wire harness are not getting stuck in
10 _ Standard Disassembly Drawings Part Figure Description DOOR HINGE [ASSEMBLY] 1. Assemble the DOOR HINGE assembly and BRACKET DOOR FRAME with machine screws. - Screws for DOOR HINGE assembly: DD81-02764A / 4 pcs - Screws for BRACKET DOOR FRAME: DD81-02728A / 2 pcs Warning Do not this work without...
Page 11 - Standard Disassembly Drawings _ 11
Standard Disassembly Drawings _ 11 Part Figure Description DOOR HINGE DW50R40**F* DW50R40**BB 5. Connect the wire harness to Sub PBA. Caution Make sure the Wire harness are not getting stuck in other parts. B A 6. Fix 8 screws to assemble the ASSY CONTROL PANEL with Torx® T15 screwdriver. - Type A: ...
Page 12 - 2 _ Standard Disassembly Drawings; Fasten 6 screws to fix the DOOR OUTER.; Use the Torx® T15 screw driver.
12 _ Standard Disassembly Drawings Part Figure Description DOOR HINGE C 8. Fasten 6 screws to fix the DOOR OUTER. NOTE : Use the Torx® T15 screw driver. - Type C: DD81-02757A / 6 pcs
Page 13 - Standard Disassembly Drawings _ 13; Remove HOLDER ROPE DOOR from the DOOR; Be careful to avoid injury from the DOOR drop; Rotate the HOLDER HINGE to release from hook.
Standard Disassembly Drawings _ 13 2-4. HOLDER HINGE - Holder Hinge : DD81-02763A / SVC-HOLDER HINGE Part Figure Description HOLDER HINGE [DISASSEMBLY] * PREPARATION: Disassemble SIDE PANEL left & right. 1. Remove HOLDER ROPE DOOR from the DOOR HINGE left & right with the DOOR closed. Warnin...
Page 14 - 4 _ Standard Disassembly Drawings; Be careful to touch the BRACKET SEAL TUB after; Pay attention to the direction of seal. If it is
14 _ Standard Disassembly Drawings 2-5. SEAL TUB PACKING - Seal Tub Packing : DD81-02898A / SVC-SEAL TUB PACKING Part Figure Description SEAL TUB PACKING Seal tub packing Bracket seal tub [DISASSEMBLY] 1. Pull out the old seal from the BRACKET SEAL TUB. Warning Be sure to remove the power plug befor...
Page 15 - Standard Disassembly Drawings _ 15; Press the seal from the top corner toward remaining; Pay attention to assemble not to deform the seal
Standard Disassembly Drawings _ 15 Part Figure Description SEAL TUB PACKING About 3~4 cm 3. Put Seal in the left & right side of the bottom. NOTE : The folded seal is about 3~4 cm long. 4. Press the seal from the top corner toward remaining side. Caution Pay attention to assemble not to deform t...
Page 16 - 6 _ Standard Disassembly Drawings; Turn the COARSE FILTER counter-clockwise to
16 _ Standard Disassembly Drawings 2-6. ROTOR LOWER / ASSY DUCT NOZZLE - Rotor Lower : DD81-02874A / SVC-ROTOR LOWER- Assy Duct Nozzle : DD82-01713A / SVC ASSY-DUCT NOZZLE (DW50R4070**/DW50R4060**/DW50R4050**) DD82-01713B / SVC ASSY-DUCT NOZZLE (DW50R4040**) Part Figure Description ROTOR LOWER / ASS...
Page 17 - Standard Disassembly Drawings _ 17; Make sure to reassemble to correct location.
Standard Disassembly Drawings _ 17 Part Figure Description ROTOR LOWER / ASSY DUCT NOZZLE Duct Nozzle assembly (DW50R4070**/DW50R4060**/ DW50R4050**) Duct Nozzle assembly (DW50R4040**) 5. Release the hooks from tub holders. Warning Do not this work without safety gloves. It can cause injury from sha...
Page 18 - 8 _ Standard Disassembly Drawings; Put the HOLDER ROTOR LOWER on the SUMP.; Pay attention to assemble the HOLDER ROTOR
18 _ Standard Disassembly Drawings Part Figure Description ROTOR LOWER / ASSY DUCT NOZZLE Sump Guide of Holder Bottom of Holder Rib [ASSEMBLY] 1. Put the HOLDER ROTOR LOWER on the SUMP. Caution Pay attention to assemble the HOLDER ROTOR LOWER correctly. There’re risks of leakage or poor performance ...
Page 19 - Standard Disassembly Drawings _ 19; Assemble the ASSY DUCT NOZZLE to hooks and
Standard Disassembly Drawings _ 19 Part Figure Description ROTOR LOWER / ASSY DUCT NOZZLE 2. Assemble the ASSY DUCT NOZZLE to hooks and on the HOLDER ROTOR LOWER. Warning Do not this work without safety gloves. It can cause injury from sharp edge. Caution Make sure to reassemble to correct location....
Page 20 - 0 _ Standard Disassembly Drawings; Be careful not to break the hooks.; Make sure to fit the hook to the correct location of
20 _ Standard Disassembly Drawings 2-7. ASSY ROTOR MIDDLE - Assy Rotor Middle : DD82-01776A / SVC ASSY-ROTOR MIDDLE Part Figure Description ASSY ROTOR MIDDLE [DISASSEMBLY] 1. Open the dishwasher’s DOOR, and take off the BASKET MIDDLE. 2. Release 2 hooks to take off ASSY ROTOR MIDDLE from the BASKET ...
Page 21 - Standard Disassembly Drawings _ 21; Turn the COARSE FILTER counter-clockwise to; Reassembly is the reverse order of disassembly.; Make sure the COARSE FILTER is closed securely.
Standard Disassembly Drawings _ 21 2-8. COARSE FILTER / FINE FILTER / MICRO FILTER - Coarse Filter : DD81-02452A / SVC-FILTER COARSE- Fine Filter : DD81-02873A / SVC-FILTER FINE- Micro Filter : DD81-02453A / SVC-FILTER MICRO Part Figure Description COARSE FILTER / FINE FILTER / MICRO FILTER [DISASSE...
Page 22 - 2 _ Standard Disassembly Drawings
22 _ Standard Disassembly Drawings 2-9. BASKET MIDDLE / ASSY ADJUSTER / BRACKET ADJUSTER - Basket Middle : DD82-01729* / SVC ASSY-BASKET MIDDLE (DW50R4060**/DW50R4050**/DW50R4040**) DD82-01714B / SVC ASSY-BASKET MIDDLE (DW50R4070**) - Assy Adjuster : DD82-01719A, DD82-01720A / SVC ASSY-ADJUSTER-L, R...
Page 23 - Standard Disassembly Drawings _ 23; Open the dishwasher’s DOOR, and take off the
Standard Disassembly Drawings _ 23 2-10. BASKET LOWER - Basket Lower : DD82-01731A / SVC ASSY-BASKET LOWER Part Figure Description BASKET LOWER [DISASSEMBLY] 1. Open the dishwasher’s DOOR, and take off the BASKET LOWER. 2. Release 2 screws to take off HANDLE BASKET. - Screws: DD81-02901A 2 pcs 3. Re...
Page 24 - 4 _ Standard Disassembly Drawings; Do not force the removal of the basket.
24 _ Standard Disassembly Drawings 2-11. BASKET 3 rd - Basket 3 rd : DD82-01769A / SVC ASSY-BASKET 3RD (DW50R4070**/DW50R4050**) Part Figure Description BASKET 3 rd (DW50R4070**/ DW50R4050**) [DISASSEMBLY] 1. Open the dishwasher’s door, and take off the BASKET 3 rd from the RAIL BASKET. 2. When you ...
Page 25 - Standard Disassembly Drawings _ 25; Take off the HOLDER RAIL REAR by pulling back; Put the RAIL BASKET on the ROLLER RAIL.; Assemble the HOLDER RAIL REAR to RAIL
Standard Disassembly Drawings _ 25 2-12. RAIL BASKET / HOLDER RAIL REAR - Rail Basket : DD81-02766A, DD81-02767A / SVC-RAIL MID-LEFT, RIGHT (All models) DD81-02958A, DD81-02959A / SVC-RAIL 3RD-LEFT, RIGHT (DW50R4070**/DW50R4050**) - Holder Rail Rear : DD81-02768A / SVC-HOLDER-RAIL MIDDLE REAR (All m...
Page 26 - 6 _ Standard Disassembly Drawings; This part will be serviced by assembly part only.
26 _ Standard Disassembly Drawings 2-13. BASKET CUTLERY - Basket Cutlery : DD81-02924A / SVC-BASKET CUTLERY (DW50R4060BB/DW50R4040BB) Part Figure Description BASKET CUTLERY [DISASSEMBLY/ASSEMBLY] This part will be serviced by assembly part only.
Page 27 - Standard Disassembly Drawings _ 27; Release the cap of softener by rotating to counter-
Standard Disassembly Drawings _ 27 2-14. CAP SOFTENER - Cap Softener: DD81-02918A / SVC-TANK WATER-SOFTENER-CAP Part Figure Description CAP SOFTENER Cap Softener [DISASSEMBLY] 1. Release the cap of softener by rotating to counter- clockwise. [REASSEMBLY] 1. Reassembly is the reverse order of disasse...
Page 28 - 8 _ Checkpoints After Finishing A Service; CHECKPOINTS AFTER FINISHING A SERVICE; unlocked when the dishwasher stops.
28 _ Checkpoints After Finishing A Service 3. CHECKPOINTS AFTER FINISHING A SERVICE 1. Check the safety device Check the operation of the door lock switch. Make sure that it is locked while the dishwasher is running and that it is unlocked when the dishwasher stops. 2. Use authenticated parts only I...
Page 29 - Asia
© 2021 Samsung Electronics Co.,Ltd. All rights reserved. Printed in Korea GSPN (GLOBAL SERVICE PARTNER NETWORK) Area Web Site Eurpoe, CIS, Mideast & africa gspn1.samsungcsportal.com Asia gspn2.samsungcsportal.com North & Latin America gspn3.samsungcsportal.com China china.samsungportal.com T...