Samsung AM036FBFDEH/EU - Installation Manual

E- 6 Concrete Hole for anchor or plug Fixing bolt (Φ9.52 or M10) Indoor Unit installation Refrigerant pipe work must be done before installing the indoor unit. Check the product and the location where it will be installed. Check the required installation conditions. Drill a hole on a floor or a wall...

E- 7 Purging the Unit On delivery, the indoor unit is loaded with inert gas. All this gas must therefore be purged before connecting the assembly piping. To purge the inert gas, proceed as follows. To prevent dirt or foreign objects from getting into the pipes during installation, do NOT remove the ...

E- 8 Cutting/Flaring the Pipes 1 M a k e s u r e t h a t y o u p r e p a r e d t h e r e q u i r e d t o o l s . (pipe cutter, reamer, flaring tool and pipe holder) 2 If you want to shorten the pipe, cut it using a pipe cutter ensuring that the cut edge remains at 90° with the side of the pipe. Ther...

E- 9 Performing Leak Test & Insulation No gap NBR(T13.0 or thicker) Insulation cover pipe Indoor unit Be sure to overlap the insulation Must fit tightly against body without any gap. Insulation pipe Check for leakage LEAK TEST WITH NITROGEN (before opening valves) In order to detect basic refrig...

E- 11 Drain pipe and Drain hose Installation Drain pan Internal water pipe (within the product) (Outer diameter Ø19) External water pipe (outside the product) (Outer diameter Ø19) 50cm or more Sewage 5cm or below Distance between the drain hose and the ground is too close End of the drain hose is in...

E- 12 Wiring Work  You must insulate refrigerant pipes, branch joints, distribution header and the pipe connection part.  Make sure to prevent any gap between the insulation on the bent part of the pipes.  Make sure that insulation is overlapped when fixing it. Indoor unit Fix securely without an...

E- 13 Wiring Work(Continued) 1 Before wiring work, you must turn off all power source. 2 Indoor unit power should be supplied through the breaker ( ELCB or MCCB+ELB ) separated by the outdoor power. ELCB: Earth Leakage Circuit Breaker MCCB: Molded Case Circuit Breaker ELB: Earth Leakage Breaker 3 Th...

E- 14 Specification of electronic wire Power supply MCCB ELB or ELCB Power cable Earth cable Communication cable Max : 242V Min : 198V X A X A, 30mmA 0.1 s 2.5mm 2 2.5mm 2 0.75~1.5mm 2  Run transmission wiring between the indoor and outdoor units through a con- duit to protect against external forc...

E- 15 Wiring Work (Continued) Example of Installation - Total power cable length L = 100(m), Running current of each units 1[A]- Total 10 indoor units were installed. 10[A] Indoor unit10 20[m] 10[m] 0[m] 9[A] 1[A] 100[m] Indoor unit2 Indoor unit1  Apply following equation. ∑ ( Coef×35.6×L k ×i k ) ...

E- 17 1 Prepare a compressor and the following tools. Tools Crimping pliers Connection sleeve (mm) Insulation tape Contraction tube (mm) Spec MH-14 20xØ6.5(HxOD) Width 19mm 70xØ8.0(LxOD) Shape 2 As shown in the figure, peel off the shields from the rubber or wire of the power cable. - Peel off 20 mm...

E- 18 Wiring Work (Continued) 5 Wrap it with the insulation tape twice or more and position your contrac- tion tube in the middle of the insulation tape. A total of three or more layers of insulation is required.  Method 1  Method 2 Insulation tape 35 mm 6 Apply heat to the contraction tube to con...

E- 19 The procedure of option setting Step 1. Entering mode to set option 1. Remove batteries from the remote controller.2. Insert batteries and enter the option setting mode while pressing High Temp button and Low Temp button. 3. Check if you have entered the option setting status. Step 2. The proc...

E- 23 1. Check whether power is supplied or not. - When the indoor unit is not plugged in, there should be additional power supply in the indoor unit. 2. The panel(display) should be connected to an indoor unit to receive option. 3. Set the installation option according to the installation condition...

E- 26 Option No. : 05XXXX-1XXXXX-2XXXXX-3XXXXX  05 series installation option(Detailed) Setting an indoor unit address and installation option(Continued) Option SEG1 SEG2 SEG3 SEG4 SEG5 SEG6 Explanation PAGE MODE Use of Auto Change Over for HR only in Auto mode (When setting SEG3) Standard heating ...

E- 28 Setting an indoor unit address and installation option(Continued) Changing a particular option Option SEG1 SEG2 SEG3 SEG4 SEG5 SEG6 Explanation PAGE MODE The option mode you want to change The tens’ digit of an option SEG you will change The unit digit of an option SEG you will change The chan...

E- 29 Setting an indoor unit address and installation option(Continued)  AM  FBFDEH  Series ※ The designs and shape are subject to change according to the model. 1 Before installing the indoor unit, assign an address to the indoor unit accord- ing to the air conditioning system plan. 2 The addr...

E- 30 Setting the function switch Switch No. Function ON OFF SW05 K1 - - - K2 Centralized control Do not use Use K3 RPM compensation - - K4 Drain pump - - SW06 K5 Revised room temperature in heat mode - - K6 Filter clean indicator 1000 hours 2000 hours K7 Hot water coil - - K8 Electric heater - - SW...

To complete the installation, perform the following checks and tests to ensure that the air conditioner operates correctly. 1 Check the followings.  Strength of the installation site  Tightness of pipe connection to detect a gas leak  Electric wiring connections  Heat-resistant insulation of the...

E- 32 Troubleshooting  If an error occurs during the operation, an LED flickers and the operation is stopped except the LED.  If you re-operate the air conditioner, it operates normally at first, then detect an error again. Detection of errors LED Display on the receiver & display unit LED Dis...

E- 34 Memo NASA_Floor Stand_AM@@@FNFDEH@_IM_EN_03678A-05.indd 34 2016-05-09 오후 5:32:40

"AEEE Yönetmeligine Uygundur" This product is RoHS compliant NASA_Floor Stand_AM@@@FNFDEH@_IM_EN_03678A-05.indd 36 2016-05-09 오후 5:32:40