Page 2 - Features; overview
_ overview Features The SRD DVR (Digital Video Recorder) employs H.264 video encoding for 8 or 16 channel inputs and G.723 audio encoding for 4 or 16 channels while simultaneously supports hard disc recording and playback. These DVRs also supports network connectivity, providing remote monitoring fr...
Page 3 - English; important saFety instructions; Follow all the safety instructions listed below.
English _ ! overview important saFety instructions Read these operating instructions carefully before using the unit. Follow all the safety instructions listed below. Keep these operating instructions handy for future reference. Read these instructions. Keep these instructions.Heed all warnings.Foll...
Page 4 - BeFore start; warning; Battery; oK; operating temperature
_ overview overview BeFore start This user manual provides Information for using the DVR such as brief introduction, part names, functions, connection to other equipment, menu setup, etc. You have to keep in mind the following notices : SAMSUNG retains the copyright on this manual. This manual canno...
Page 5 - standards approvals
English _ ! overview standards approvals This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a ...
Page 6 - contents
_ overview overview contents overview 2 2 Features 3 Important Safety Instructions 4 Before Start 8 Part Names and Functions (Front) 10 Part Names and Functions (Rear) 13 Remote Control instaLLation 15 15 Checking the installation environment 16 Rack Installation 16 HDD Addition connecting with othe...
Page 7 - weB viewer
English _ ! overview search & pLay 70 70 Search 73 Playback weB viewer 74 74 Introducing Web Viewer 75 Connecting Web Viewer 77 Using Live Viewer 83 Using Search Viewer 87 Viewer Setup 97 About BacKup viewer 98 98 SEC Backup Viewer appendix 100 100 Product Specification (SRD-830/830D/1610/ 1610D...
Page 12 - Used to transfer a video signal to other video devices.
1_ overview overview Part Names Functions AUDIO IN Audio input signal port (RCA jack) and port for optional audio extension cable. SRD-1650/1650D/1670/1670D (Audio 5~16CH) SRD-850/850D/870/870D (Audio 5~8CH) AUDIO OUT Audio Signal Output Port (RCA jack). VIDEO IN Composite Video Signal Input Port (B...
Page 13 - remote controL; dvr; Available after switching to DVR mode by pressing the [; using the numeric buttons; Press each button between 1 to 9.
English _1 ! overview remote controL dvr Available after switching to DVR mode by pressing the [ dvr ] button on the remote control. using the numeric buttons CHANNEL 1–9 Press each button between 1 to 9. CHANNEL 10 Press the [ +10 ] button first, then press the 0 button again within 3 seconds. CHAN...
Page 14 - monitor; Available after switching to Monitor mode by pressing the [; Press any button among 1 to 9.; changing the remote control id; The factory default ID of the remote control is 00.
1_ overview overview monitor Available after switching to Monitor mode by pressing the [ monitor ] button on the remote control. using the numeric buttons CHANNEL 1–9 Press any button among 1 to 9. changing the remote control id Press the ID button of the remote control and check the ID displayed on...
Page 15 - insta; Please take note of the followings before using this product.; checKing the instaLLation environment; installation
English _1 ! insta LL ation Please take note of the followings before using this product. Do not use the product outdoor. Do not spill water or liquid in the connection part of the product. Do not impose the system to excessive shock or force. Do not pull out the power plug forcefully. Do not disass...
Page 16 - racK instaLLation; Install the Bracket-Rack as shown in the figure, and then fasten the; hdd addition; You can install additional HDDs.; cautions when adding a hdd; Please check the HDD compatibility before adding a HDD.
1_ installation installation racK instaLLation Install the Bracket-Rack as shown in the figure, and then fasten the screws on both sides (2 screws on each side). Fix the screws not to be loosened by vibrations. hdd addition You can install additional HDDs. Make sure to unplug the power cord from the...
Page 18 - You can check the HDD map directly on the DVR.
1_ installation installation When the installation of additional HDDs is done, connect the power cable and connect the HDD signal cables (SATA Cable) to connectors ~ on the main board. You can check the HDD map directly on the DVR. Refer to “ Storage Device > HDD Map ”. (Page 48) Note that th...
Page 20 - The following figures are based on Model SRD-1670D.; connecting the usB; menu; connecting with other device
0_ connecting with other device The following figures are based on Model SRD-1670D. connecting the video, audio, and monitor connecting the usB There are two USB ports at the front and one at the back of the product.You can connect a USB HDD, USB CD/DVD player, USB memory or mouse to the USB port.If...
Page 21 - connecting externaL sata hdd; The Alarm In/Out port at the back is composed of the following.
English _1 ! connecting with other device connecting externaL sata hdd SRD-830/830D/1610/1610D/1630/1630D does not support a port for SATA connection. There are two external SATA ports on the rear side of the product.If an external SATA HDD is connected to the system, recognition and settings are av...
Page 22 - connecting the rs-485 device; Connect the RS-485 device through the back port.; ALARM OUT
_ connecting with other device connecting with other device ALARM IN 1 ~ 8 (SRD-830/830D/850/850D/870/870D) : Alarm Input Port ALARM IN 1 ~ 16 (SRD-1610/1610D/1630/1630D/1650/1650D/1670/1670D) : Alarm Input Port ALARM RESET : On receiving an Alarm Reset signal, the system cancels the current Alarm I...
Page 23 - connecting the networK; connecting to the internet using the router; INTERNET
English _ ! connecting with other device connecting the networK connecting to internet through ethernet (10/100/1000Baset) connecting to the internet using the router Router xDSL or Cable Modem xDSL or Cable Modem External Remote PC DDNS Server (Data Center) INTERNET Windows Network Viewer Back Bone...
Page 24 - connecting to internet through adsL
_ connecting with other device connecting with other device connecting to internet through adsL Hub/Switcher Phone(ADSL) Line ADSL MODEM RJ-45 Ethernet Cable (Direct Cable) Windows Network Viewer INTERNET
Page 25 - Live; getting started; starting the system; For the permission management, refer to “; live
English _ ! Live getting started starting the system Connect the power cable of the DVR to the wall outlet.Press the Power button on the front panel. You will see the initialization screen. The initialization process will last about 1 minute. If a new HDD is installed, the initialization process may...
Page 26 - The login dialog will also appear if you press a menu button on; Locking all Buttons
_ live live Login To access a DVR or restricted menu, you should have logged in to the DVR. In live mode, right-click any area of the screen. You will see the context sensitive menu as in the right figure. Click < Login >. The login dialog appears. You can also see the login dialog to access a...
Page 27 - Live screen conFiguration; icons on the Live screen
English _ ! Live Live screen conFiguration icons on the Live screen You can check the status or operation of the DVR with the icons on the live screen. Name Description Current Date, Time Displays the current time and date. Login Information When you are logged in, the “ LOG ON ” icon will be displa...
Page 28 - error information; If the cooling fan does not work properly or has a problem, the <; Live screen menu; clicking the mouse any area in live mode.; split mode menu
_ live live error information If you turn on the system when the internal HDD is not connected or an error occurs, the “HDD FAIL” icon ( ) will be displayed on the top left corner. In this case, make sure you contact the service center for assistance as this may cause a failure of recording, playbac...
Page 29 - single mode menu; The single mode menu is available only in Single Mode.
English _9 ! Live Menu Description Scene Mode Refer to “ Live Mode ”. (Page 31) Spot Out Refer to “ Spot Out ”. (Page 33) Audio On/Off Refer to “ Audio ON/OFF ”. (Page 34) Freeze Refer to “ Freeze ”. (Page 34) Stop Alarm Stops the alarm output and the event monitoring. Refer to “ Event Monitoring ”....
Page 30 - view the Launcher menu; The Launcher menu appears on the bottom of the live screen.
0_ live live view the Launcher menu The Launcher menu appears on the bottom of the live screen. In Live mode, right-click to display the context menu and select < show Launcher >. Move the cursor to the bottom and click a desired item in the Launcher menu. If no input is entered for 10 seconds...
Page 31 - Live mode; layout of split screens.; switching the screen mode; mode; switching the split mode; auto sequence; Setting the Device
English _1 ! Live Live mode SRD-1610/1610D/1630/1630D/1650/1650D/1670/1670D display Live images from 16 channels in a total of 8 layout of split screens. switching the screen mode To switch the split mode, select a screen mode in the launcher menu, or right-click to select a screen mode in the conte...
Page 32 - manual switching; channel setting; Ex : if switching CH 1 to CH 7
_ live live manual switching Press the left/right button on the front panel or the remote control, or click the arrow < _ / + > key to move to the next split mode. If pressing the right [ + ] button in 9-split mode : 9-split (CH 1~9) mode 9-split (CH 10~16) mode Auto Sequence If pressing t...
Page 33 - switching to single mode; Refer to “; spot out; selecting a spot out mode; can select a output screen mode.
English _ ! Live switching to single mode When in split mode, select and double-click a desired channel to switch to its Single mode. Press the number corresponding to a desired channel on the front panel or the remote control to switch to its Single mode. Refer to “ remote control > using the nu...
Page 34 - Zoom; In the enlarged image, use the direction buttons (; audio on/oFF in single mode; Only the channel where <; FreeZe
_ live live Zoom This is available only in Single Live mode. In Single mode, select a desired area and use the Zoom function to enlarge it twice. Select < Zoom > in the right-click menu. Press the [ Zoom ] button on the front panel or the remote control, or simply click < > in the launch...
Page 35 - event monitoring
English _ ! Live event monitoring This will display the channel in sync with a specific event (Sensor/Motion/Video Loss) if it occurs. In “ monitor > event display ”, set the event monitoring to ON/OFF and specify the event display time. (Page 52) If multiple events occur simultaneously, the scre...
Page 36 - SyStem Setup; ] button on the remote control or on the; using the DVR
36_ using the DVR You can setup the system properties, devices, and options for recording, event, backup and network. SyStem Setup You can setup Date/Time/Language, Permission, System Properties and Log. Date/time/Language You can check and setup the current Date/Time and time related properties, as...
Page 37 - using the dvr; Use direction buttons (; using the Calendar; Select year and month.
English _37 ! using the dvr - Time Server : Enter an IP or URL address of the time server. - Last Sync Time : Displays the most recent synchronization time from the selected time server. - Activate as Server : Set to < use > to allow the DVR to act as a Time Server for other DVRs. DST : Set up...
Page 38 - permission management; Setting the Administrator; By default, initial ID and password are set to “; using Virtual Keyboard; Caps Lock
38_ using the DVR using the DVR permission management You can set permissions of each user over the DVR's specific function and settings. Setting the Administrator You can set and change Administrator’s ID and password. The administrator can use and set all menu items and functions. Using the mouse ...
Page 39 - Setting the Group; to set the group authority
English _39 ! using the dvr Setting the Group You can create user groups and setup permissions for those user groups. You can register a user for each group in < user >. Using the mouse may help make setup easier. Use the up/down buttons ( ▲▼ ) in < system > window to move to < permis...
Page 40 - to restrict the user permissions; to change the user password; user menu
40_ using the DVR using the DVR to restrict the user permissions If the admin restricts all permissions of an added group, the users belonging to that group can access only the default minimum menus and can change the user’s own password only. Start the DVR. If all permissions are restricted, only t...
Page 41 - Setting the user; Setting permissions; If it is not checked (
English _41 ! using the dvr Setting the user Users can be added only if a group was created in < group > menu. Using the mouse may help make setup easier. Use the up/down buttons ( ▲▼ ) in < system > window to move to < permission management >, and press [ enter ] button. Select &l...
Page 42 - Use the virtual keyboard to enter the user ID.; System management; Checking the System Information; system
42_ using the DVR using the DVR Manual Input of ID : Prompts you to enter the user ID manually for the login process. - Checked ( ) : Encloses the registered user IDs with the [ ] symbols. Use the virtual keyboard to enter the user ID. When the permission setup is done, press < oK >. System ...
Page 44 - Include Network Settings; Log Information
44_ using the DVR using the DVR Settings You can copy and import the DVR settings by using a storage media. Using the mouse may help make setup easier. Use the up/down buttons ( ▲▼ ) in < system > window to move to < system management >, and press [ enter ] button.Select < settings &g...
Page 45 - event Log; Use the four direction buttons (
English _45 ! using the dvr event Log Event log shows recorded events on alarms, motion detections and video loss. It also shows the log and its timestamp. Using the mouse may help make setup easier. Use the up/down buttons ( ▲▼ ) in < system > window to move to < Log information >, and ...
Page 46 - SettInG tHe DeVICe; Setting the Camera; > : Shows information other than the video of the selected channel.
46_ using the DVR using the DVR SettInG tHe DeVICe You can setup Camera, Storage Device, Remote Device, POS Device and Monitor. Camera Setting the Camera You can set Video, Audio, Channel Name and Dwell Time of a Camera. Using the mouse may help make setup easier. Press the [ menu ] button on the re...
Page 47 - Setting the ptZ; ) to move to a desired
English _47 ! using the dvr Progressive : You can set the progressive camera to ON/OFF. If you set it to < ON > for the progressive camera, screen flickering will be reduced. Screen Setup : The video appeared on the screen may vary depending on the channel’s camera, configure the DVR display t...
Page 48 - You can check information on storage devices.; Confirming Devices; HDD Map
48_ using the DVR using the DVR Storage Device You can check information on storage devices. Confirming Devices You can check storage devices and their free space, usage as well as status. Devices available are HDD, and USB devices (Memory, HDD, CD/DVD). Refer to “ product specifications > Backup...
Page 49 - Formatting; - Alarm signal will output through the alarm out port on the
English _49 ! using the dvr Formatting You can format a storage device. Using the mouse may help make setup easier. Use the up/down buttons ( ▲▼ ) in < device > window to move to < storage device >, and press [ enter ] button. Select < Format >. A window for selection of device for...
Page 50 - Check; Remote Devices; pOS Devices
50_ using the DVR using the DVR Duration : Sets the alarm duration for the alarm signal and beep sound. - Check Alarm, Replace Alarm signals will output through the selected alarm out ports (1, 2, 3, and 4).- If < Beep > was selected, a beep will sound. - If < all > was selected, both be...
Page 52 - Setting the monitor
52_ using the DVR using the DVR monitor You can configure information to be displayed and its format for Spot Out monitor. Setting the monitor Using the mouse may help make setup easier. Use the up/down buttons ( ▲▼ ) in < device > window to move to < monitor >, and press [ enter ] butto...
Page 53 - Setting the Spot Out; Setting the Screen mode
English _53 ! using the dvr Setting the Spot Out You can set the DVR to output information / video apart from the monitor out. Using the mouse may help make setup easier. Use the up/down buttons ( ▲▼ ) in < device > window to move to < monitor >, and press [ enter ] button. Select < s...
Page 54 - SettInG tHe ReCORDInG; Recording Schedule; ] button on the remote control or front
54_ using the DVR using the DVR SettInG tHe ReCORDInG You can setup scheduled recording, event recording and other recording related settings. Recording Schedule Make your reservation on a date and time to schedule the recording on specified time. Using the mouse may help make setup easier. Press th...
Page 55 - Recording Color tags; event Record Duration; ReC Quality / Resolution; Setting Standard Recording properties; Remaining count
English _55 ! using the dvr Recording Color tags color Function description White No Recording No schedule / event recording Orange Continuous Scheduled recording only Blue Event Event recording only Green Both(Cont&Evnt) Both scheduled / event recordings Each press of a selected cell will cycle...
Page 56 - Setting event Recording properties; If you set the resolution to <; Resolution; for the same channel on any other page.
56_ using the DVR using the DVR Setting event Recording properties You can set each channel’s resolution, quality and IPS for event recordings. Using the mouse may help make setup easier. Use the up/down buttons ( ▲▼ ) in < record > window to move to < rec Quality & resolution >, and...
Page 57 - SettInG tHe eVent; Sensor Detection; Preset setup can be done in PTZ mode.
English _57 ! using the dvr Disk End Mode : If selected < overwrite >, recording will continue despite the HDD full while overwriting the oldest. If selected < stop >, the recording will stop when the HDD is full. Disk End Beep : If selected < stop >, the button is activated. If yo...
Page 58 - motion Detection; For further information on alarm output, refer to “; Setting the motion Detection Area
58_ using the DVR using the DVR Alarm : Sets the alarm output method. For further information on alarm output, refer to “ HDD Alarm > Alarm ”. (Page 49) Duration : Sets the duration of alarm signal and alarm sound. When the sensor detection setup is done, press < oK >. motion Detection You ...
Page 59 - Video Loss Detection
English _59 ! using the dvr Video Loss Detection You can set the alarm to be generated on a camera disconnection, which causes a video loss. Using the mouse may help make setup easier. Use the up/down buttons ( ▲▼ ) in < event > window to move to < video Loss detection >, and press [ ent...
Page 60 - BACKup; Setting the Backup; You can backup the desired data to a connected device.
60_ using the DVR using the DVR BACKup You can check the backup device and set the backup schedule by channel or by time. The product only supports external HDD of USB memory/DVD and USB/SATA type. (Page 100) Setting the Backup You can backup the desired data to a connected device. Using the mouse m...
Page 61 - netwORK COnFIGuRAtIOn; Connection mode; You can set the network connection route and protocol.; Setting the Connection; Sets the protocol and environment of the network.
English _61 ! using the dvr When the backup setup is done, press < oK >. If no available device is recognized for backup, < OK > button is not activated. The application may slow down during the backup.You can switch to the menu screen during the backup in operation, but playback of data...
Page 62 - Dynamic IP; Setting the protocol
62_ using the DVR using the DVR IP, Gateway, Subnet Mask, and DNS - For < static ip > : You can directly input IP address, Gateway, Subnet Mask and DNS. - For < dynamic ip > : IP address, Gateway, and Subnet Mask are set automatically. - For < adsL > : IP address, Gateway, and Subn...
Page 63 - DDnS; You can set the DDNS site for a remote user’s network connection.; Use virtual keyboard to enter user inputs.; Connecting and Setting the network; when no router is used; Consult your network manager for IP, Gateway and Subnet Mask.
English _63 ! using the dvr DDnS You can set the DDNS site for a remote user’s network connection. Using the mouse may help make setup easier. Use the up/down buttons ( ▲▼ ) in < network > window to move to < ddns >, and press [ enter ] button. Use virtual keyboard to enter user inputs. ...
Page 64 - when a router is used; enter “
64_ using the DVR using the DVR when a router is used To avoid IP address conflict with the DVR's static IP, check followings : setting the dvr with a static ip - Internet connection : You can connect the DVR to a router which is connected to an ADSL/Cable modem or a router in a Local Area Network (...
Page 65 - DDnS Setting; > menu of the connected DVR to the following :; Live transfer
English _65 ! using the dvr DDnS Setting DDNS is a short form of Dynamic Domain Naming System. DNS (Domain Name System) is a service that routes a domain name consisting of user friendly characters (ex : www.google.com) to an IP address consisting of numbers (64.233.189.104). DDNS (Dynamic DNS) is a...
Page 66 - mailing Service; If an event occurs with a channel where the camera’s video is set to <; Smtp Setting; Sets the SMTP mail server.; ) to move to a desired item; event Setting
66_ using the DVR using the DVR mailing Service You can send an e-mail to a DVR-registered user at a specific time interval, or if an event occurs. If an event occurs with a channel where the camera’s video is set to < OFF > or the remaining recording count is set to < OFF >, only the te...
Page 67 - Group Setting; Recipient Setting
English _67 ! using the dvr Group Setting You can set the group to whom the e-mail is sent, and specify the permission for each group. You can add recipients for each group in the < recipient > menu item. The recipient is set separately from the DVR user group. Using the mouse may help make se...
Page 68 - COntROLLInG A ptZ DeVICe; ptZ Device; Getting started with ptZ; using the ptZ camera; ptZ control
68_ using the DVR using the DVR COntROLLInG A ptZ DeVICe The DVR enables you to adjust the settings of a PTZ camera as well as an ordinary one to your preference. ptZ Device The PTZ device can be activated only if a channel in connection with the PTZ camera is selected. Getting started with ptZ The ...
Page 69 - preset Setting; save; Camera Setting; In “; SAMSUNG PROTOCOL
English _69 ! using the dvr Focus : Enables you to adjust the focus manually.Auto Pan : The camera automatically runs between the two points that you selected.Scan : The camera moves to the preset points in the specified sequence. If multiple presets are specified, the PTZ camera will automatically ...
Page 70 - SeARCH; ] button on the remote control or; time Search; Select a date to search.
70_ search & play SeARCH You can perform the search for recorded data by the time or by the search criteria such as an event. You can access the < search > menu directly in Live mode. In Live mode, right-click any area of the screen. The Live menu appears.Select < search >. Or, press...
Page 71 - Lay; event Search
English _71 ! search & p Lay Zoom In : The map enlarges in detail. It will switch in the sequence of 24 hours - 4 hours - 1 hour - 5 minutes.Zoom Out : The map will switch in the reverse order of the detailed mode above. It will switch in the sequence of 5 minutes - 1 hour - 4 hours - 24 hours. ...
Page 72 - pOS Search; You can enter specific text to refine your search.; motion Search; If you set the motion area to <
72_ search & play search & play pOS Search You can search for data in the POS device that is connected to the DVR. You can use the mouse to select the related items. Select < pos search > in the < search > menu. Use direction buttons ( ▲▼_ + ) to set the search criteria and press...
Page 73 - pLAyBACK; play; Backup range
English _73 ! search & p Lay pLAyBACK play You can play data stored in the HDD and backup a desired portion of the data. Using the mouse may help make setup easier. In Live mode, click < play > in the right-click menu or < > in the launcher menu, or press the Play button on the remot...
Page 74 - IntRODuCInG weB VIeweR; pRODuCt FeAtuReS; Windows XP Professional; web viewer
74_ web viewer IntRODuCInG weB VIeweR what is web Viewer? Web Viewer allows remote access to your DVRs. You have access to live video, archived video, PTZ control (if configured), etc. pRODuCt FeAtuReS Remote access from a standard browserSupports PTZ camera controlsSupports 1, 4, 8, 16 camera viewi...
Page 75 - Iewe; COnneCtInG weB VIeweR
English _75 ! w e B V Iewe R COnneCtInG weB VIeweR Open your web browser and type the IP address or URL of DVR into the URL address box. The basic URL of the DVR is as following in case of MAC address : 00-00-F0-ab-cd-ef : nabcdef.websamsung.net00-16-6c-ab-cd-ef : mabcdef.websamsung.net00-68-36-ab-c...
Page 76 - You may have “
76_ web viewer web viewer You may have “ windows Security Alert ” that attempts to block this with the Windows Firewall. In that case, click < unblock > to start Web Viewer. Installation is complete. Now you can see the main screen of Live Viewer. 6. 7.
Page 77 - uSInG LIVe VIeweR; The Live Viewer screen consists of following :
English _77 ! w e B V Iewe R uSInG LIVe VIeweR The Live Viewer screen consists of following : This displays the IP address and the model name of the connected DVR. These menus consist of < LIVe >, < SeARCH >, < Setup >, < ABOut >. These buttons are used for the screen split a...
Page 78 - OSD InFORmAtIOn DISpLAy; If you have set PTZ cameras for the DVR, “
78_ web viewer web viewer OSD InFORmAtIOn DISpLAy The channel number, video size, and IP address of the connected DVR are displayed. The current date and time will be displayed according to the selected time information display setting < DVR time > or < pC time >. Alarm icon appears when...
Page 79 - COnneCteD DVR; No Response; Setting the display of the OSD time information; SEQUENCE
English _79 ! w e B V Iewe R COnneCteD DVR This displays the IP address and the status of the connecting DVR. Connection failure message No Response : Appears when the DVR does not respond. Access Denied : Appears when the maximum number of users is exceeded. The number of simultaneous connections a...
Page 80 - neXt; SAVInG tHe LIVe SCReen On tHe pC; CAptuRe
80_ web viewer web viewer neXt : When this button is clicked, the next screen appears. In SINGLE MODE, the channel numbers are sequentially switched from 1 to 16. In QUAD MODE, the screens are changed like 1st 4 channels (1~4) 2nd 4 channels (5~8) 3rd 4 channels (9~12) 4th 4 channels (13~16). ...
Page 81 - CHAnGInG tHe LIVe SCReen CHAnneL
English _81 ! w e B V Iewe R ReCORD : Saves the current image on the screen and saves it as a avi video file. To record it, it is required at least 1GB of available space.The default saving path is “C:\Program Files\Samsung\Dvr Web Viewer\VideoClip\Live”. To change the saving path, click < SAVE P...
Page 83 - uSInG SeARCH VIeweR; The Search Viewer screen consists of following :
English _83 ! w e B V Iewe R uSInG SeARCH VIeweR The Search Viewer screen consists of following : This displays the IP address and the model name of the connected DVR. These menus consist of < LIVe >, < SeARCH >, < Setup >, < ABOut >. These buttons are used for the screen spl...
Page 84 - You can change the split mode by clicking each number icon.; This displays the IP address and the status of the connecting DVR.
84_ web viewer web viewer SpLIt-SCReen You can change the split mode by clicking each number icon. Click < > button. The screen displays the selected camera connected to the DVR in “ SInGLe mODe ”. Click < > button. The screen displays the selected camera connected to the DVR in “ QuAD m...
Page 86 - SeARCHInG tHe ReCORDeD VIDeO In tHe CALenDAR; today; SeARCHInG tHe ReCORDeD VIDeO In tHe tImeLIne; The channels are ranging from CH01 to CH16.
86_ web viewer web viewer SeARCHInG tHe ReCORDeD VIDeO In tHe CALenDAR If the video data has been recorded on a date, the date is distinguished in green. If you click the date, the recorded video information is displayed in the time line. When you click < today >, it is changed to today’s date...
Page 87 - COntROLLInG pLAyBACK; VIeweR Setup
English _87 ! w e B V Iewe R COntROLLInG pLAyBACK Fast Backward : Reverse-plays faster(2x). Reverse play : Performs Reverse Play. play : Performs playback. Fast Forward : Plays faster(2x). Go to First : Moves the beginning time of recorded video in the time line. Step Backward : Performs one step re...
Page 88 - Set the time synchronization.; You can change the admin ID or the password.
88_ web viewer web viewer time Synchronization Setup Set the time synchronization. Display Date Format : Set the date type.Time : Select a time format to display on the screen. DSt (Daylight Saving time) DST is displayed an hour ahead of the standard time of the time zone. Language Select a preferre...
Page 90 - You can check and change the settings of the storage device.
90_ web viewer web viewer Device You can check a list of devices that are connected to the DVR and configure the necessary settings. Click < Device > in the menu screen. For more information, refer to “ Setting the Device ”. (Page 46) Camera Camera You can configure the settings of the camera ...
Page 91 - You cannot set to use the POS device remotely.
English _91 ! w e B V Iewe R HDD Alarm You can set the alarm output channel and the alarm duration for an error. Remote Device You can see a list of remote devices including PTZ cameras and system keyboards that are connected to the RS-485 port of the DVR and configure the necessary settings. pOS De...
Page 92 - Setting the Recording
92_ web viewer web viewer Spot Out The registered user can view the event screen for the duration set in < event Display > if an event occurs from the appropriate channel. The number of Spot Out terminals differs according to the model. mode You can switch between live mode and play mode. Reco...
Page 93 - You can set the Disk End Mode.; event; Setting the event
English _93 ! w e B V Iewe R event Record Duration You can set the start and end times of recording that will be activated if an event occurs. ReC Quality & Resolution Standard/event You can set the resolution, frame rate and recording quality for each channel. Record Option You can set the Disk...
Page 94 - motion Region; You can set the alarm output time if a video loss occurs.
94_ web viewer web viewer motion Detection You can set the motion detection mode and the sensitivity as well as the alarm output type and the duration. motion Region Set the target motion detection area Video Loss Detection You can set the alarm output time if a video loss occurs. Alarm Schedule You...
Page 95 - network; network Configuration; You can check the DDNS settings.; A remote user can set the images of the DVR.
English _95 ! w e B V Iewe R network For more information, refer to < network Configuration >. (Page 61) Connection A remote user can access the DVR via the network to check the current mode and the IP address. Connection You can set the network connection route. protocol You can configure the...
Page 96 - Smtp
96_ web viewer web viewer mailing Service You can specify the SMTP server that sends a mail if an event occurs and set the recipient group and users. Smtp You can set the server that sends mails and specify if you use the authentication process. event You can set the event interval and specify which...
Page 97 - ABOut
English _97 ! w e B V Iewe R ABOut Click < ABOut >. Displays the model name of connected DVR and the version of Web Viewer.
Page 98 - SeC BACKup VIeweR; Recommended System Requirements; backup viewer
98_ backup viewer SeC BACKup VIeweR You can play a file that is backed up in the format of SEC.Backup in the format of SEC will involve in generating two files: one for the backup data and one for the viewer.If you run the backup file viewer, the backup data file will be automatically played. Recomm...
Page 99 - ACK
English _99 ! B ACK up V Iewe R Name Description Audio / A toggle button. Each time you press this button, the audio output will toggle between activated and deactivated. You can adjust the volume level from 0 to 100. Screen Printout Saves the current screen as an image file. Supported file formats ...
Page 100 - Item; appendix
100_ appendix pRODuCt SpeCIFICAtIOn (SRD-830/830D/1610/1610D/1630/1630D) Item Details Note Operating System Embedded OS Broadcast Format NTSC/PAL System Input Voltage AC 100~240V Power Consumption SRD-830/830D/1610/1610D/1630/1630D : 55W Video Video In Composite 16(8) Channel - 1.0Vp-p - 75 Ω Hi Z T...
Page 101 - ppen
English _101 ! A ppen DIX Item Details Note Record Compression Method Video : H.264 Audio : G.723 Resolution & Quality Resolution Spec. (Quality) Max Recording Rate CIF(S) 352X240(NTSC) /352X288(PAL) Level8 (high) ~ Level1 (low) 240(120)ips(NTSC)/ 200(100)ips(PAL) 2CIF(M) 704x240(NTSC) /704x288(...
Page 106 - pRODuCt OVeRVIew
106_ appendix appendix pRODuCt OVeRVIew SRD-1670D ~ USB
Page 107 - DeFAuLt SettInG; Use System/Load Factory Default in MENU
English _107 ! A ppen DIX DeFAuLt SettInG This returns the factory default settings.The settings are made as follows; Use System/Load Factory Default in MENU The default settings are based on SRD-1670D. Category Details Factory Default System Settings Date/Time/Language Date/Time/Language Date YYYY-...
Page 108 - Category
108_ appendix appendix Category Details Factory Default Device POS Device OFF Monitor Monitor Display All Switch to Split Screen 5 sec VGA 800x600 HDMI 480p Sharpness Level1(Low) Display Position Setup 30 Spot Out Spot Out 1 CH1 ~ CH4 Spot Out 2 CH5 ~ CH8 Spot Out 3 CH9 ~ CH12 Spot Out 4 CH13 ~ CH16...
Page 110 - tROuBLeSHOOtInG
110_ appendix appendix tROuBLeSHOOtInG Symptom Countermeasures The system does not turn on and the indicator on the front panel does not work at all. Check if the power supply system is properly connected. Check the system for the input voltage from the power source. If the problem persists even aft...
Page 112 - Symptom
112_ appendix appendix Symptom Countermeasures Recording does not work. If your player does not display a Live image at all, that indicates recording does not work so first check if you see an image on the screen. Recording does not work if the recording settings are not properly configured. Manual ...
Page 113 - Open SOuRCe LICenSe RepORt On tHe pRODuCt
Gnu GeneRAL puBLIC LICenSe Version 2, June 1991 Copyright (C) 1989, 1991 Free Software Foundation, Inc. 51 Franklin Street, Fifth Floor, Boston, MA 02110-1301, USAEveryone is permitted to copy and distribute verbatim copies of this license document, but changing it is not allowed. preamble The licen...
Page 117 - teRmS AnD COnDItIOnS
Some devices are designed to deny users access to install or run modified versions of the software inside them, although the manufacturer can do so. This is fundamentally incompatible with the aim of protecting users' freedom to change the software. The systematic pattern of such abuse occurs in the...
Page 121 - use with the Gnu Affero General public
litigation (including a cross-claim or counterclaim in a lawsuit) alleging that any patent claim is infringed by making, using, selling, offering for sale, or importing the Program or any portion of it. 11. patents. A “contributor” is a copyright holder who authorizes use under this License of the P...
Page 122 - Interpretation of Sections 15 and 16.; preamble
and conditions either of that numbered version or of any later version published by the Free Software Foundation. If the Program does not specify a version number of the GNU General Public License, you may choose any version ever published by the Free Software Foundation. If the Program specifies th...
Page 130 - SALES NETWORK; SAMSUNG TECHWIN AMERICA Inc.
SALES NETWORK SAMSUNG TECHWIN CO., LTD. Samsungtechwin R&D Center, 701, Sampyeong-dong, Bundang-gu, Seongnam-si, Gyeonggi-do, Korea, 463-400 TEL : +82-70-7147-8740~60 FAX : +82-31-8018-3745 SAMSUNG TECHWIN AMERICA Inc. 1480 Charles Willard St, Carson, CA 90746, UNITED STATES Tol Free : +1-877-21...