Ryobi RT102- User Manual

7 eXteNSION COrDS When using a power tool at a considerable distance from a power source, be sure to use an extension cord that has the capacity to handle the current the product will draw. An undersized cord will cause a drop in line voltage, resulting in overheating and loss of power. Use the char...

8 FeatUreS prODUCt SpeCIFICatIONS Table Dimensions ...........................................13 in. x 18 in.Maximum Cutter Diameter .................................1-15/16 in.Fence Length.............................................................. 18 in. Fig. 1 VACUUM ATTACHMENT MITER GAUGE SWIT...

9 UNpaCKING This product requires assembly.  Carefully remove the product and any accessories from the box. Make sure that all items listed in the packing list are included.  Inspect the product carefully to make sure no breakage or damage occurred during shipping.  Do not discard the packing mat...

10 Fig. 5 aSSeMBLY Fig. 3 WarNING: The router table should never be connected to a power supply when you are assembling parts, making adjust-ments, installing or removing cutters, cleaning, or when not in use. Disconnecting the router table will prevent accidental starting that could cause serious p...

11 MITER GAUGE SLoT BAR aSSeMBLY Fig. 6 attaCHING tHe UNDer taBLe GUarD See Figure 5.  Place the router table upside down on a flat surface.  Position the under table guard around the throat of the table.  Align the three holes of the guard with the threaded holes in the table.  Use the hex key ...

1 1 rev=1/8” aSSeMBLY attaCHING tHe rOUter GUarD tO tHe rOUter See Figure 9.  Place the router guard on the back of the router.  Align the slots in the guard with the holes in the router.  Secure the router guard to the router with the two guard screws. attaCHING tHe rOUter tO tHe taBLe See Figur...

14 OperatION WarNING: Failure to unplug the router and router table could result in accidental starting causing serious injury. WarNING: To prevent damage to the spindle or spindle lock, always allow the motor to come to a complete stop before en-gaging the spindle lock. WarNING: Use this router tab...

15 To LooSEN SPINDLE LoCK To TIGHTEN CoLLET NUT Fig. 17 INSertING/reMOVING CUtterS See Figure 17.  Unplug the router table.  Remove the screws from the router guard.  Remove the router guard from the router. to install the bit:  Push the spindle lock in and hold into place. NOte: To make sure th...

16 OperatION perFOrMING a rOUtING OperatION See Figure 19. Observe the following rules when using the router.  Read the entire Operator’s Manual for the R163 router.  Adjust the infeed fence to support the uncut workpiece and adjust the outfeed fence to support the workpiece after the cut. The “0”...

17 aDJUStING tHe MIter GaUGe See Figure 21.  Loosen the miter gauge knob.  Rotate the miter gauge to the desired angle.  Tighten the miter gauge knob. INSertING tHe StartING pIN See Figure 22. Place the starting pin on the router table and use it as a pivot point when cutting small, odd-shaped pi...

18 OperatOr’S MaNUaL rOUter taBLe rt102 983000-9854-4-08 (REV:03) RT10 • PARTS AND SERVICE Prior to requesting service or purchasing replacement parts, please obtain your model and serial number from the product data plate. • MODEL NUMBER • SERIAL NUMBER • HOW TO OBTAIN REPLACEMENT PARTS: Replacemen...