Ryobi CB120N- User Manual

English

12V nickel cadmium BaTTeRY Pack

cB120n

Use this battery pack for Ryobi 12 V cordless products only.

Refer to the Operator’s Manual provided with product. Always

mention the appropriate model number when communicating

with us regarding your battery pack.

WaRninG!

Read and undeRsTand all insTRucTions.

Failure to follow all instructions listed below, may result

in electric shock, fire and/or serious personal injury.



Battery tools do not have to be plugged into an elec-

trical outlet; therefore, they are always in operating

condition. Be aware of possible hazards when not

using your battery tool or when changing accesso-

ries.

Following this rule will reduce the risk of electric

shock, fire, or serious personal injury.



do not place battery tools or their batteries near

fire or heat.

This will reduce the risk of explosion and

possibly injury.



do not crush, drop or damage battery pack. do not

use a battery pack or charger that has been dropped

or received a sharp blow.

A damaged battery is subject

to explosion. Properly dispose of a dropped or damaged

battery immediately.



Batteries can explode in the presence of a source

of ignition, such as a pilot light.

To reduce the risk of

serious personal injury, never use any cordless product

in the presence of open flame. An exploded battery can

propel debris and chemicals. If exposed, flush with water

immediately.



do not charge battery tool in a damp or wet location.

Following this rule will reduce the risk of electric shock.



use battery only with charger listed.

For use with 12V

nickel cadmium battery packs, see tool/appliance/bat-

tery pack/charger correlation supplement 988000-449.



For best results, your battery tool should be charged

in a location where the temperature is more than

50°F but less than 100°F.

To reduce the risk of serious

personal injury, do not store outside or in vehicles.



under extreme usage or temperature conditions,

battery leakage may occur. if liquid comes in con-

tact with your skin, wash immediately with soap

and water. if liquid gets into your eyes, flush them

with clean water for at least 10 minutes, then seek

immediate medical attention.

Following this rule will

reduce the risk of serious personal injury.



When battery pack is not in use, keep it away from

other metal objects like: paper clips, coins, keys,

nails, screws, or other small metal objects that can

make a connection from one terminal to another.

Shorting the battery terminals together may cause

sparks, burns, or a fire.



always remove battery pack from your tool when you

are assembling parts, making adjustments, cleaning,

or when not in use.

Removing battery pack will prevent

accidental starting that could cause serious personal

injury.



always remove battery pack before storing the

device.



When battery becomes fully charged, unplug the

charger from the power supply and remove the bat-

tery pack from the charger.



always wear eye protection with side shields marked

to comply with ansi Z87.1.

Failure to do so could

result in objects being thrown into your eyes and other

possible serious injuries.



keep battery pack dry, clean, and free from oil and

grease.

Always use a clean cloth when cleaning. Never

use brake fluids, gasoline, petroleum-based products,

or any solvents to clean battery pack.



save these instructions.

Refer to them frequently and

use them to instruct others who may use this tool. If you

loan someone this tool, loan them these instructions

also.

NOTICE:

If at any point during the charging process none of the

LEDs on charger are lit, remove the battery pack from

the charger to avoid damaging the product. DO NOT

insert another battery. Return the charger and battery to

your nearest service center for service or replacement.

cHaRGinG THe BaTTeRY Pack

See Figures 1 - 2.

Battery packs are shipped in a low charge condition to

prevent possible problems. Therefore, you should charge

prior to first use. If the charger does not charge the battery

pack under normal circumstances, return both the battery

pack and charger to your nearest Authorized Service Center

for electrical check.



Charge the battery pack only with the recommended

charger.



Do not place the charger and battery pack in an area

of extreme heat or cold. They will work best at normal

room temperature.



The battery pack may become slightly warm to the

touch while charging. This is normal and does not

indicate a problem.

using c120n charger:



Insert charger plug into input jack making sure they are

properly connected.



Connect the charger to a power supply. For approved

power sources, refer to the operator’s manual for the

charger.



When batteries become fully charged, unplug the

charger from the power supply and disconnect from

the battery pack.

GeneRal saFeTY Rules

oPeRaTion